Rj45 Connectors And Twisted Pair Cables - Lightware MX-FR9 User Manual

   
3. Product Overview
Symmetrical Analog Stereo Audio
A 5-pole Phoenix connector is used for balanced analog audio (line in/out). Some I/O
boards use this connector as a configurable input or output. Always check if this
connector is configured as an output or input to prevent connecting two outputs
together.
Unbalanced audio signals can be connected as well. For asymmetrical output, connect only + and ground.
For asymmetrical input, connect + and ground to the source and connect – to the ground.
Compatible Plug Type
Phoenix® Combicon series (3.5mm pitch), type: MC 1.5/5-ST-3.5, order number: 1840395.
Please see the short guide about the audio cable wiring in the
3.14.4. RJ45 Connectors and Twisted Pair Cables
The Wiring of Twisted Pair Cables
Lightware recommends the termination of TP cables on the basis of TIA/EIA T 568 A or TIA/EIA T 568 B
standards.
Pin TIA/EIA T568A Wire color TIA/EIA T568B
1 white/green
2 green
3 white/orange
4 blue
5 white/blue
6 orange
7 white/brown
8 brown
MX-FR Series Modular Matrix Frames – User's Manual
Pin nr. Signal
1 Left +
2 Left -
3 Ground
4 Right -
5 Right +
Cable Wiring Guide section.
Wire color
Side
white/orange
orange
white/green
blue
Bottom
white/blue
green
white/brown
Top
brown
Applied CPU2 firmware: v3.5.7b8 | LDC software: v2.5.17b2
MX-TP Input and Output Ports
HDMI-TP and DVI-TP interface boards provide standard RJ-45 connectors for VIDEO IN
/ OUT and DDC IN / OUT. Please note that the DDC connector is not available on the MX-
DVI-TP-IB and MX-DVI-TP-OB, but available on the MX-DVI-TP-IB+ and MX-DVI-TP-OB+
boards.
Pin VIDEO IN/OUT
1 TMDS Data0+
2 TMDS Data0- Hot Plug Detect (in) Hot Plug Detect (out)
3 TMDS Clock+
4 TMDS Data1+
5 TMDS Data1-
6 TMDS Clock-
7 TMDS Data2+
8 TMDS Data2-
MX-TPS, MX-TPS2 Inputs and Outputs
MX-TPS boards provide standard RJ-45 connectors for TPS extenders or MX boards.

ATTENTION! The same RJ-45 connector is used for Ethernet. Avoid connecting
LAN cables to the TPS connectors. If the port of the TPS board was set to AUTO
mode, it is able to recognize the LAN cable and swap to Ethernet fallback mode
automatically. In this case, the port works as an Ethernet switch, but a TPS CAT
cable is not allowed to be connected to the Ethernet port.
LED1, Amber 
Remote power is
OFF
disabled
Blinking
1 flash / sec
Blinking
2 flashes / sec
Blinking
6 flashes / sec
Remote power is
ON
enabled
DDC IN DDC OUT
CEC (no conn.) CEC (no conn.)
RS-232 RX RS-232 RX
DDC CLK DDC CLK
+12V (out) +12V (out)
RS-232 TX RS-232 TX
DDC SDA DDC SDA
GND GND
LED2, Green
No TPS link
Low power mode,
N/A
RS-232 and Ethernet
Low power mode,
N/A
only RS-232
N/A Ethernet fallback mode
TPS link is active
32