I/O Port Commands; Tps And Tps2 Port - Lightware MX-FR9 User Manual

   
7. Programmer's Reference
7.10. I/O Port Commands
7.10.1. TPS and TPS2 Port
7.10.1.1. Port Parameters and Settings
Query or set the TPS port-related parameters. The format and the usage are the same in the case of the input
and output ports.
Supported Boards
▪ MX-TPS-IB, -A, -S; MX-TPS2-IB-P, -AP, -SP
▪ MX-4TPS2-4HDMI-IB, -A, S; MX-4TPS2-4HDMI-IB-P, -AP, -SP
▪ MX-4TPS2-4HDMI-OB, -A, S; MX-4TPS2-4HDMI-OB-P, -AP, -SP
▪ MX-TPS-OB, -A, -S; MX-TPS2-OB-P, -AP, -SP
Querying the Parameters
Command and Response
ȩ {:TPS#<in/out>@<S><I/O>=?}
Ȩ (TPS#<in/out>@<S><I/O>=<mod>;<eth>;<cmod>;<pwr>;<upl>;<qual>;<err>;<len>;<rid>;<tmp>)CrLf
Example
ȩ {:tps#1@so=?}
Ȩ (TPS#1@SO=H;1;H;0;0;17161617;23222020;0;0384;38;)CrLf
The state of the 1st output is: HDBaseT mode is selected, Ethernet is enabled.
Setting the Parameters
Command and Response
ȩ {:TPS#<in/out>@<S><I/O>=<mod>;<eth>}
Ȩ (TPS#<in/out>@<S/A><I/O>W=<mod>;<eth>;<cmod>;<pwr>;<upl>;<qual>;<err>;<len>;<rid>;<tmp>)CrLf
Example
ȩ {:tps#1@so=L;x}
Ȩ (TPS#1@SO=L;1;H;0;0;17161617;23222020;0;0384;38;)CrLf
The TPS mode of the selected port is set to Longreach, the Ethernet setting was not changed. The response
shows the new values. Use the 'x' character to keep the actual value of a parameter.
MX-FR Series Modular Matrix Frames – User's Manual
Parameters
Identifier
<in>/<out> Input or output port number
<I/O>
<mod>
<eth>
<tmp>
<cmod>
<pwr>
<upl>
<qual>
<err>
<len>
<rid>
<tmp>
Applied CPU2 firmware: v3.5.7b8 | LDC software: v2.5.17b2
Parameter Description
Read/write Parameters
Port number in 1- or 2-digit ASCII format (01, 3, 04, etc.)
I = input
Input or output port type
O= output
H = HDBaseT
L = Longreach
Mode of the selected TPS port A = Automatic
1 = Low power 1, RS-232 only
2 = Low power 2, RS-232 + Ethernet
0 = Ethernet is disabled
Ethernet status of the selected
1 = Ethernet is enabled (default)
port
2-15 = reserved for future use
Temperature [integer] Measured temperature of the board in Celsius.
Read-only Parameters
E: Ethernet fallback
1: Low power 1, RS-232 only
2: Low power 2, RS-232+ETH
The current mode of the L: Longreach
selected TPS port H: HDBaseT
0 (zero): Link is not present
- (hyphen): The chip is under external process
(e.g. during boot, fw update)
Remote power source presence 0 (zero): Not connected
(all ports carry the same state) 1: Connected
Ethernet uplink status 0 (zero): Ethernet is inactive
(all ports carry the same state) 1: Ethernet is active
Quality of the link Measured values give information about the quality of the
[HEXA number] link
Maximum measured error Measured values give information about the quality of the
[HEXA number] cable.
The measured length of the Measured length of the link cable. If the cable is shorter
cable (meters) – informative than 20m the response is 0. If the cable is longer than
only 110m the response is 1000. If there is no data the
Valid for CAT5e cable response is 0, as well.
Remote device identifier Lightware devices have a unique ID for identifying each
[HEXA number] other.
Temperature [integer] Measured temperature of the board in Celsius.
120
Parameter Values