Hdmi Input Port - Lightware MX-FR9 User Manual

   
7. Programmer's Reference
7.10.1.2. Remote Power Settings (PoE)
Query or set the PoE-compatible remote power state of the TPS2 port. The format and the usage are the
same in the case of the input and output ports.
Supported Boards
▪ MX-TPS2-IB-P, -AP, -SP
▪ MX-4TPS2-4HDMI-IB-P, -AP, -SP
▪ MX-4TPS2-4HDMI-OB-P, -AP, -SP
▪ MX-TPS2-OB-P, -AP, -SP
Querying the Parameters
Command and Response
ȩ {:POE#<in/out>@S<I/O>=?}
Ȩ (POE#<in/out>@S<I/O>=<mode>;<status>;)CrLf
Example
ȩ {:poe#1@so=?}
Ȩ (POE#1@SO=0;0;)CrLf
The PoE is disabled on the Output 1 (and inactive).
Setting the Parameters
Command and Response
ȩ {:POE#<in/out>@S<I/O>=<mode>;<status>}
Ȩ (POE#<in/out>@S<I/O>=<mode>;<status>;)CrLf
Example
ȩ {:poe#1@so=1;0}
Ȩ (POE#1@SO=1;0;)CrLf
The PoE is set to enabled on Output 1 but not active.
Parameters
Identifier Parameter description
Enable/disable the PoE
<mode>
feature
Remote power sending
<status>
(read-only parameter)
MX-FR Series Modular Matrix Frames – User's Manual
Parameter values
0 = PoE is disabled; 1 = PoE is enabled
0 = power sending is not in progress (inactive)
1 = power sending is in progress (active)
Applied CPU2 firmware: v3.5.7b8 | LDC software: v2.5.17b2
7.10.2. HDMI Input Port
7.10.2.1. Port Parameters and Settings
Query or set the HDMI port-related parameters (not the HDMI-3D port!).
Supported Boards
▪ MX-HDMI-IB; MX-DVI-HDCP-IB; MX-HDMI-TP-IB; CPU-IB (Test input)
Querying the Parameters
Command and Response
ȩ {:HDMI#<in>@<S/C/A>I=?}
Ȩ (HDMI#<in>@<S/C/A>I=<info>;<video>;<audio>;<adv_info>;<in_set>;)CrLf
Example
ȩ {:HDMI#17@SI=?}
Ȩ (HDMI#17@SI=S1131;V1920x1080p60,675,00;A1C010000;I1111IA;PA1;)CrLf
The actual settings are in the response; see the Parameters of each block for the details.
Setting the Parameters
Command and Response
ȩ {:HDMI#<in>@<S/C/A>I=<a><b>}
Ȩ (HDMI#<in>@<S/C/A>I=<info>;<video>;<audio>;<adv_info>;<in_set>;)CrLf
Example
ȩ {:HDMI#17@SI=x;0;}
Ȩ (HDMI#17@SI=S1131;V1920x1080p60,675,00;A1C010000;I1111IA;PA0;)CrLf
The HDCP setting is changed to 'disabled' (0). The legend of
<in_set> block section. Use the 'x' character to keep the actual value of a parameter. The response contains
the new settings in the <in_set> block.
121
<a> and <b> parameters are described in the