7. Programmer's Reference
7.10.8.2. Input Port Parameters
Query or set the analog audio input port parameters (signal levels).
Supported Boards
▪
MX-TPS-IB-A, -AP; MX-TPS-OB-A, -AP
▪
MX-4TPS2-4HDMI-IB-A; MX-4TPS2-4HDMI-IB-AP
▪
MX-HDMI-3D-IB-A; MX-HDMI-3D-OB-A
▪
MXD-UMX-IB
Querying the Parameters
Command and Response
ȩ {:AUDIN#<in/out>@<S/C/A><I/O>=?}
Ȩ (AUDIN#<in/out>@S<I/O>=<vol>;<bal>;<gain>;<ph>;<res>;)CrLf
Example
ȩ {:AUDIN#9@SI=?}
Ȩ (AUDIN#9@SI=6300;50;0;0;0;)CrLf
The actual setting is in the response; see the legend for the details.
Setting the Parameters
Command and Response
#analogaudio
ȩ {:AUDIN#<in/out>@<S/C/A><I/O>=<vol>;<bal>;<gain>;<ph>;x}
Ȩ (AUDIN#<in/out>@S<I/O>=<vol>;<bal>;<gain>;<ph>;<res>;)CrLf
Example
ȩ {:AUDIN#9@SI=0}
Ȩ (AUDIN#9@SI=0;50;0;0;0;)CrLf
The 'Volume' is changed to 0 dB, the others are left unchanged.
Parameters
Identifier
Parameter Description
<vol>
Volume level
<bal>
Balance
<gain>
Gain (input volume level)
The phase invert of the
<ph>
outgoing signal
<res>
Reserved
#volume
#gain
Parameter Values
Values are accepted between -63 and 0 dB (step is 1
dB) and rounded. e.g. 6000 = -60 dB; 3625 = -36 dB
Values are accepted between 0 and 100 (step is 1):
e.g. 50 = center (default)
Accepted values: 0, 3, 6, 9, 12, 15, 18, 21, 24
0 = disabled
1 = enabled
Applied CPU2 firmware: v3.5.7b8 | LDC software: v2.5.17b2
MX-FR Series Modular Matrix Frames – User's Manual
7.10.9. DVI-DL Output Port
Query or set the dual-link DVI output port parameters.
Supported Boards
▪
MX-DVIDL-OB
7.10.9.1. Port Parameters and Settings
Querying the Parameters
Command and Response
ȩ {:ISL54105#<out>@<S/C/A>O=?}
Ȩ (ISL54105#<out>@SO=<curr>;<preemp>;<band>;<mode>;)CrLf
Example
ȩ {:ISL54105#9@SO=?}
Ȩ (ISL54105#9@SO=7;15;2;2;)CrLf
The actual setting is in the response.
Setting the Parameters
Command and Response
ȩ {:ISL54105#<out>@<S/C/A>O=x;x;x;<mode>}
Ȩ (ISL54105#<out>@SO=<curr>;<preemp>;<band>;<mode>;)CrLf
Example
ȩ {:ISL54105#9@SO=x;x;x;0}
Ȩ (ISL54105#9@SO=7;15;2;0;)CrLf
The DVI port mode is changed to Dual link mode, the are others left unchanged. Use the 'x' character to keep
the actual value of a parameter.
Parameters
Identifier
<curr>
<preemp>
<band>
<mode>
The first three parameters are for internal use, type 'x' character instead and set the desired DVI port mode
by the fourth parameter.
Parameter Description
Parameter Values
Output level
PreEmphasis
Port-related parameters (internal use)
PLL bandwidth
0 = Dual-link mode is active
1 = Sinlge-link mode is active
DVI port mode (DL/SL)
2 = Auto mode (the dual-link half controlled
automatically depending on the input signal)
138