Hdmi Output Port - Lightware MX-FR9 User Manual

   
7. Programmer's Reference
<ext_info> block
Additional information about the 3D-capable ports is displayed in this block. The first character is E.
Format: E<addon><TPG_res><TPG_alert><FW_mode>
Identifier Parameter Description
The type of the installed
<addon>
audio add-on board
The resolution of the test
<TPG_res>
pattern
Test pattern alert
<TPG_alert>
information
The forwarded signal mode
<FW_mode>
from the board
Example: E1400
S/PDIF add-on board is installed at the given port; the Test pattern generator is active at 720x480p60
resolution running without errors. The forwarded signal is DVI.
<in_set> block
You are able to verify the actual settings on the selected input ports with this block, as this block is always
present. The first character is P, the second is X.
Format: PX<HDCP_mode><TPG_mode><TPG_clock><TPG_screen><Audio_mode>
Identifier Parameter Description
<HDCP_mode> HDCP mode setting
The mode of the Test
<TPG_mode>
pattern generator
The resolution of the test
<TPG_clock>
pattern
<TPG_screen> The type of the test pattern
Audio mode setting of the
<Audio_mode>
installed add-on board **
Parameter Values
0 = no add-on board is installed
1 = add-on type is S/PDIF
2 = add-on type is stereo (UDA)
3 = add-on type is stereo (ADAV)
F = add-on type is stereo but initialization is failed
0 = Test pattern generator is inactive
3 = active, the resolution is 720x576p@50Hz
4 = active, the resolution is 720x480p@60Hz
0 = no error
1 = unsupported resolution is detected
0 = DVI 3 = HDMI, 36 bit
1 = HDMI, 24 bit 4 = HDMI, 48 bit
2 = HDMI, 30 bit
#nosyncscreen #testpattern
Parameter Values
0 = HDCP is disabled 1 = HDCP is enabled
0 = off, test pattern is not sent (default)
1 = on, test pattern is always sent
2 = test pattern is sent if there is no incoming signal
0 = 720x480p60 2 = the same as the incoming
1 = 720x576p50 signal *
0 = solid red 6 = chessboard
1 = solid green 7 = color bar
2 = solid blue 8 = cycle (the patterns
3 = solid black are switched in every two
4 = solid white seconds)
5 = ramp
A = no audio D = Deembed to external
B = HDMI passthrough E = HDMI + deembed
C = Embed from external
Applied CPU2 firmware: v3.5.7b8 | LDC software: v2.5.17b2
MX-FR Series Modular Matrix Frames – User's Manual
* The supported resolutions in the case of the test pattern generator: 480p60, 576p50, 720p50, 720p60,
1080p50, 1080p60.
** See more information about the Audio modes in the
Example: PX1007B
HDCP is enabled; Test pattern generator is off; the original audio of the HDMI signal is embedded
(passthrough).
7.10.3.2. Timing Parameters
The system continuously measures the parameters of the incoming signals. The answer consists of 16
data bytes and every data byte is represented as a two-digit hexadecimal number. The parameters could be
useful for advanced debugging processes.
Supported Boards
▪ MX-HDMI-3D-IB, -A, -S
▪ MX-4TPS2-4HDMI-IB, -A, -S; MX-4TPS2-IB-P, -AP, -SP
Command and Response
ȩ {:TIMINGS#<in>@<S/C/A>I=?}
Ȩ (TIMINGS#<in>@<S/C/A>I=<Timing_codes>)CrLf
Example
ȩ {:TIMINGS#17@SI=?}
Ȩ (TIMINGS#17@SI=0360027102D002402C0501004008630C)CrLf
For more information about the measured values, please contact Lightware Support.
7.10.4. HDMI Output Port
7.10.4.1. Port Parameters and Settings
Query or set the HDMI output port related parameters.
Supported Boards
▪ MX-HDMI-OB; MX-DVI-HDCP-OB; MX-HDMI-TP-OB
Querying the Parameters
Command and Response
ȩ {:HDMI#<out>@<S/C/A>O=?}
Ȩ (HDMI#<out>@<S/C/A>O=<GEN_INFO>;<VIDEO>;<ADV_INFO>;<OUT_SET>;<SINK>;)CrLf
Example
ȩ {:HDMI#1@SO=?}
Ȩ (HDMI#1@SO=G11101;V720x576p51,313,00;I0011AA;OAAAAA;M110111077;)CrLf
The actual settings are in the response; see the Parameters of each block for the details.
127
Audio Settings section.