Dvi-Opt Output Port; Ricod Related Commands; Setting The Ricod Master Command - Lightware MX-FR9 User Manual

   
7. Programmer's Reference
7.10.10. DVI-OPT Output Port
Query or set the DVI-OPT output port parameters.
Supported Boards
▪ MX-DVI-OPT-OB
7.10.10.1. Port Parameters and Settings
Querying the Parameters
Command and Response
ȩ {:TOSA#<out>@<S/C/A>O=?}
Ȩ (TOSA#<out>@SO=<laser>;<opt_cod>;)CrLf
Example
ȩ {:TOSA#9@SO=?}
Ȩ (TOSA#9@SO=1;C;4TCDP1081BT;LC;30;31;26;31;22;24;22;24;3;2;0)CrLf
The actual setting is in the response, see the legend.
Setting the Parameters
Command and Response
ȩ {:TOSA#<out>@<S/C/A>O=<laser>;}
Ȩ (TOSA#<out>@SO=<laser>;<opt_cod>;)CrLf
Example
ȩ {:TOSA#9@SO=?}
Ȩ (TOSA#9@SO=1;C;4TCDP1081BT;LC;30;31;26;31;22;24;22;24;3;2;0)CrLf
The Laser has been enabled, the others were left unchanged.
Parameters
Identifier Parameter Description
<laser> Laser beam setting
<opt_cod> Optical module-related parameters for internal use
MX-FR Series Modular Matrix Frames – User's Manual
Parameter Values
0 = disable laser
1 = enable laser
Applied CPU2 firmware: v3.5.7b8 | LDC software: v2.5.17b2
7.11. RICOD Related Commands
7.11.1. Setting the RICOD MASTER Command
Sets the RICOD command for the selected input port.
Command and Response
ȩ {:RICOD#<in>@<S/A>I=<A1><A2>;<B>;<C>;}
Ȩ (RICOD#<in>@SI=<A1><A2>;<B>;<C>;)CrLf
Parameters
Identifier Parameter Description
<in> Input port number
<S/A> Affected ports
RICOD enable parameter on
<A1>
the input
Remote lock enable parameter
<A2> (it takes effect only if RICOD is
enabled by <A1>)
<B> The selected video input
<C> The selected audio input

INFO: If the first character of <A1><A2>
on this input .
Example
ȩ {:ricod#1@SI=10;2;1;}
Ȩ (RICOD#1@SI=10;2;1;)CrLf
RICOD control is enabled on the first input port, which unlocks the remote device and selects the second
video input and the first audio input port on it.
Parameter Values
Input number in 1 or 2 digit ASCII format (01, 3, 04 etc.)
S = single selected input
A = all inputs
1: The RICOD function is enabled to this input port on the
local device (where the command was given).
0: The RICOD function is disabled to this input port on the
local device (where the command was given).
1: The front panel buttons (of a transmitter) or the output
(of a video matrix) is locked on the remote device.
0: The front panel buttons (of a transmitter) or the output
(of a video matrix) is unlocked on the remote device.
- (hyphen) = There is no video switch command.
A = Automatic input select must be performed on the
remote device if available. (i.e. Autoselect function)
0 (zero) = The output needs to be muted if available.(switch
to zero)
1 , 2 , ... , 80: Use the given input number if available.
- (hyphen) = There is no video switch command.
A = Automatic input select must be performed on the
remote device if available. (i.e. Autoselect function)
0 (zero) = The output needs to be muted if available.
1, 2, ... , 80: Use the given input number if available.
is zero, then no command is sent, the RICOD function is disabled
139