GE Multilin MM3 Motor Manager 3 Instruction Manual page 171

CHAPTER 8: COMMUNICATIONS
MM3 MOTOR MANAGER 3 – INSTRUCTION MANUAL
Table 8–2: Modbus Memory Map (Sheet 12 of 28)
Modicon Address
dec. hex
44242 4241 1091 Interlock 7 startup override
delay
44243 4242 1092 Interlock 7 running
override delay
44244 4243 1093 Interlock 7 operation
44245 4244 1094 Interlock 7 instantaneous
alarm
44246 4245 1095 ...Reserved...
44247 4246 1096 ...Reserved...
44248 4247 1097 ...Reserved...
44249 4248 1098 Interlock input 8 function
44250 4249 1099 Interlock 8 startup override
delay
44251 4250 109A Interlock 8 running
override delay
44252 4251 109B Interlock 8 operation
44253 4252 109C Interlock 8 instantaneous
alarm
44254 4253 109D ...Reserved...
44255 4254 109E ...Reserved...
44256 4255 109F ...Reserved...
44257 4256 10A0 Interlock input 9 function
44258 4257 10A1 Interlock 9 startup override
delay
44259 4258 10A2 Interlock 9 running
override delay
44260 4259 10A3 Interlock 9 operation
44261 4260 10A4 Interlock 9 instantaneous
alarm
44262 4261 10A5 ...Reserved...
44263 4262 10A6 ...Reserved...
44264 4263 10A7 ...Reserved...
44265 4264 10A8 Interlock input 10 function
44266 4265 10A9 Interlock 10 startup
override delay
44267 4266 10AA Interlock 10 running
override delay
44268 4267 10AB Interlock 10 operation
44269 4268 10AC Interlock 10 instantaneous
alarm
44270 4269 10AD Auto mode definition
* – Maximum setpoint value and 65535 represent OFF; ** – 1/phase current scale factor × A; *** – 101
represents unlimited;
† – Minimum setpoint value represents OFF; ~ – 0.1 × A when high resolution mode is disabled;
0.01 × A when enabled
Description Range
0 to
3601
0 to
3601
0 to 1
0 to 1
...
...
...
0 to 34
0 to
3601
0 to
3601
0 to 1
0 to 1
...
...
...
0 to 34
0 to
3601
0 to
3601
0 to 1
0 to 1
...
...
...
0 to 34
0 to
3601
0 to
3601
0 to 1
0 to 1
0 to 1
MODBUS MEMORY MAP
Step Units Format Default
1 s F1*
1 s F1*
1 --- F18 0 = IL
STOP
1 --- F14 0 =
DISABLE
... ... ...
... ... ...
... ... ...
1 --- F17 0 = NOT
USED
1 s F1*
1 s F1*
1 --- F18 0 = IL
STOP
1 --- F14 0 =
DISABLE
... ... ...
... ... ...
... ... ...
1 --- F17 0 = NOT
USED
1 s F1*
1 s F1*
1 --- F18 0 = IL
STOP
1 --- F14 0 =
DISABLE
... ... ...
... ... ...
... ... ...
1 --- F17 0 = NOT
USED
1 s F1*
1 s F1*
1 --- F18 0 = IL
STOP
1 --- F14 0 =
DISABLE
1 --- F27 0 =
SERIAL
0
0
...
...
...
0
0
...
...
...
0
0
...
...
...
0
0
8–27