GE Multilin MM3 Motor Manager 3 Instruction Manual page 168

MODBUS MEMORY MAP
8–24
Table 8–2: Modbus Memory Map (Sheet 9 of 28)
Modicon Address
dec. hex
44157 4156 103C Overload pickup level
44158 4157 103D ...Reserved...
44159 4158 103E ...Reserved...
44160 4159 103F ...Reserved...
Motor protection: ground fault (read/write setpoints)
44161 4160 1040 Ground fault alarm level
(residual)
44162 4161 1041 Ground fault alarm level
(50:0.025 CT)
44163 4162 1042 Ground alarm delay on run
44164 4163 1043 Ground fault trip level
(residual)
44165 4164 1044 Ground fault trip level
(50:0.025 CT)
44166 4165 1045 Ground trip delay on run
44167 4166 1046 Delay contactor ground
fault trip (Aux. 1)
44168 4167 1047 Delay contactor ground
fault trip (Aux. 2)
44169 4168 1048 ...Reserved...
Motor protection: options (read/write setpoints)
44170 4169 1049 Minimize reset time
44171 4170 104A Stopped motor cooling
time
44172 4171 104B Overload trip reset
44173 4172 104C Phase unbalance alarm
44174 4173 104D Thermal capacity alarm
44175 4174 104E Open control circuit trip
44176 4175 104F Reset alarms using the
reset key
44177 4176 1050 Underpower alarm level
44178 4177 1051 Underpower alarm delay
44179 4178 1052 Underpower trip level
44180 4179 1053 Underpower trip delay
44181 4180 1054 Acceleration time alarm
delay
44182 4181 1055 Acceleration time trip delay
* – Maximum setpoint value and 65535 represent OFF; ** – 1/phase current scale factor × A; *** – 101
represents unlimited;
† – Minimum setpoint value represents OFF; ~ – 0.1 × A when high resolution mode is disabled;
0.01 × A when enabled
Description Range
100 to
125
...
...
...
10 to
101
1 to
151
1 to 60
10 to
101
0 to
151
0 to 50
0 to
1000
0 to
1000
...
0 to 1
5 to
1080
0 to 1
0 to 1
1 to
101
0 to 1
0 to 1
Load protection (read/write setpoints)
2 to
11001
1 to 60
2 to
11001
1 to 60
5 to
1255
5 to
1255
MM3 MOTOR MANAGER 3 – INSTRUCTION MANUAL
CHAPTER 8: COMMUNICATIONS
Step Units Format Default
1 0.01 × F1 100 = 1.00
× FLC
FLC
... ... ...
... ... ...
... ... ...
1 % of F1* 65535 =
FLC OFF
1 0.1 × F1* 65535 =
A OFF
1 s F1
1 % of F1* 65535 =
FLC OFF
1 0.1 × F1* 65535 =
A OFF
1 0.1 × F1 10 = 1.0
s
100 ms F1
100 ms F1
... ... ...
1 --- F14 1 =
ENABLE
1 minut F1
es
1 --- F16 0 =
MANUAL
1 --- F14 1 =
ENABLE
1 % F1* 101 =
OFF
1 --- F14 0 =
DISABLE
1 --- F14 0 =
Disable
1 0.1 × F1* 65535 =
kW OFF
1 s F1
0.1 ×
1 F1* 65535 =
kW OFF
1 s F1
5 0.1 × F1* 65535 =
s OFF
5 0.1 × F1* 65535 =
s OFF
...
...
...
10
0
0
...
30
10
10