Time-Date - Honeywell NOTIFIER NFW-50X Manual

Programming
These screens allow the programmer to enter a two line custom banner. A flashing cursor will appear in the bottom left corner of each
display. A maximum of 20 characters (including spaces) can be entered into each screen for a total of two lines with 40 characters. After
entering up to 20 characters in the first screen, press Enter to view the second screen. Enter up to 20 characters in the second screen in
the same manner or just press Enter if a second banner line is not being entered. To quickly clear the current banner, press the CLR key.
To enter alphanumeric characters from the keypad, repeatedly press the appropriate key until the desired character is displayed in the
first position. For example, to enter the letter B, press the 2 (ABC) key three times to toggle through the characters 1, A, and B. Press the
right arrow key to move the cursor one position to the right and repeat the process to enter the next character. To enter a space, press the
9 (YZ) key four times to place a blank in the desired position. When all characters have been entered, press the Enter key to store the
information. The display will return to the Banner Screen.

Time-Date

SYSTEM SETUP
1=TROUBLE REM
2=BANNER
3=TIME-DATE
System Setup Screen #1

Time
To change the time, press 1 while viewing the Time-Date Screen. The following screen will be displayed:
A flashing cursor is located toward the top left of the display. Below the cursor is the current time. To change the time, enter the two-digit
hours followed by the two-digit minutes. The cursor will move one position to the right each time a digit is entered. After the last min-
utes digit is entered, the cursor will again move one position to the right. At this point enter 1 for AM or 2 for PM. The display will then
return to the Time-Date Screen which will show the new time entry. If an error is made while entering a digit, press the CLR key to delete
the entire entry and beginning again.

Date
To change the date, press 2 while viewing the Time-Date Screen. The following screen will be displayed:
A flashing cursor is located toward the top left of the display. Below the cursor is the current date. To change the date, enter the two-digit
month followed by the two-digit day and then the two-digit year (17 for 2017, 18 for 2018, etc.). The cursor will move one position to
the right each time a digit is entered. After the last year digit is entered, the display will return to the Time-Date Screen which will show
the new date entry. If an error is made while entering a digit, press the CLR key to delete the entire entry and beginning again.

Clock Format
The clock can be configured to display 12 hour (AM & PM) or 24 hour (military) time. Pressing 3 while viewing the Time-Date screen
will cause the display to toggle between 12HR and 24HR. Select 12HR for 12 hour display or 24HR for 24 hour display.
NOTE: If the clock is changed to 24 hour (military) format, the date will change to the European standard of Day-Month-Year (for display
purposes only).

Daylight Savings Time
TIME AND DATE
1=DAYLIGHT SAVINGS
Time & Date Screen #2
Pressing 1 while viewing Daylight Savings Screen #1 will cause the display to toggle between Enabled Yes and Enabled No. The control
panel will automatically update the time for daylight savings time when Enabled Yes is selected.
Pressing 2 while viewing Daylight Savings Screen #1 will display another screen which allows the programmer to select the month that
daylight savings time will begin. In this sub-screen, pressing 1 will select March, 2 will select April, and 3 will select May.
70
The control panel time and date can be changed by pressing 3 while viewing the System Setup Screen #1.
The following screen will be displayed:
TIME AND DATE
1=TIME 10:00 AM
2=DATE 05-04-2017
3=CLOCK FORMAT
Time-Date Screen #1
ENTER TIME
10:00 AM
1=AM
ENTER DATE
MONTH DAY YEAR
05-04-17
Pressing 1 while viewing Time-Date Screen #2 will cause the following screens to be displayed:
DAYLIGHT SAVINGS
1=ENABLED YES
2=START MONTH
3=START WEEK WEEK-2
Daylight Savings Screen #1
TIME AND DATE
1=DAYLIGHT SAVINGS
12HR
Time-Date Screen #2
2=PM
Time Screen
Date Screen
DAYLIGHT SAVINGS
1=END MONTH
2=END WEEK
MAR
Daylight Savings Screen #2
NFW-50X Manual — P/N LS10129-001NF-E:C 7/25/2018
Master Programming Level
NOV
WEEK-1