Table of Contents
Advertisement
Master Programming Level
1=STANDARD ADJECTIVE
2=STANDARD NOUN
3=CUSTOM ADJECTIVE
4=CUSTOM NOUN
Noun/Adjective Screen
1=BASEMENT
2=BOILER RM
3=CLASSROOM
Noun Screen #1
1=KITCHEN
2=LOBBY
3=OFFICE
Noun Screen #5
Pressing 3 or 4 while viewing the Noun/Adjective Screen will display screens similar to the previous Adjective and Noun Screens. The
new screens will list Custom Adjectives and Nouns which have been programmed into the control panel using the FS-Tools utility.
Description
EDIT MONITOR
1=NOUN/ADJECTIVE
2=DESCRIPTION
Edit Monitor Screen #5
A flashing cursor will appear at the first asterisk to the left. The programmer can enter additional descriptive information about the
device being programmed. This information will appear on the LCD display along with the standard device label information.
A maximum of 20 characters (including spaces) can be entered. To enter alphanumeric characters from the keypad, repeatedly press the
appropriate key until the desired character is displayed in the first position. For example, to enter the letter B, press the 2 (ABC) key three
times to toggle through the characters 2, A and B. Press the right arrow key to move the cursor one position to the right and repeat the
process to enter the next character. To enter a space, press the * (QZ) key four times until a blank appears in the desired position. When
all characters have been entered, press the Enter key to store the information. The display will return to the Edit Monitor Screen #4, dis-
playing the new information at the bottom of the screen.
Recall/Increment Function
In addition, the user may use the Recall/Increment function at any time when the cursor is on the first letter of the Adjective or Noun
field as follows:
•
If the zero key is pressed, a 0 is placed in the first letter position
•
If the zero key is then pressed a second time with no intervening key actions, the entire Adjective field is replaced with the field
entered for the previous device programmed, and the cursor moves to the last character of the field (Recall function). The Recalled
Adjective or Noun field may now be changed letter-by-letter
•
If the zero key is pressed again with no other intervening key actions and the last character in the field is a number 0-9, the number
is incremented by one. If the last character is a letter, it changes to a 0. If the last character is 9 it goes to 0
•
The above increment function may be repeated with each press of the zero key
As an example, the user could quickly enter 'FLR_3_ROOM 305' as follows:
1.
The cursor is on the first letter of the Adjective field. Press the zero key twice to display FLR_3
2.
With the cursor on the first letter of the Noun field, press the zero key twice to recall the display ROOM_304. The cursor
automatically jumps from the first to the last letter of the Noun field
3.
With the cursor on the last letter of the Noun field, press the zero key again to increment the room number to 305
4.
Press the right arrow key to advance the zone field
5.
Select a zone number from 000 to 049. Z000 (default zone) is the general alarm zone. Z001 through Z049 may be selected to link
software zones
NFW-50X Manual — P/N LS10129-001NF-E:C 7/25/2018
Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed.
Note that the keyboard down arrow key must be pressed to see all the Noun screens. Press the number cor-
responding to the noun that is to be used as a descriptor for the location of the monitor module currently
being programmed.
1=CLOSET
2=CORRIDOR
3=ELECTRIC RM
Noun Screen #2
1=PATIENT
2=RESTROOM
3=ROOM
Noun Screen #6
The Description selection allows the programmer to enter additional information about the monitor module
currently being programmed. This information will be displayed as part of the device label on the LCD dis-
play. Pressing 2 while viewing Edit Monitor Screen #5 will cause the following screen to be displayed:
DESCRIPTION
NOUN/ADJECTIVE
Noun/Adjective Screen
1=ELEVATOR
2=ENTRANCE
3=FLOOR
Noun Screen #3
1=STAIRWAY
2=STOREROOM
3=WING
Noun Screen #7
1M012
Programming
1=GARAGE
2=HALLWAY
3=HVAC RM
Noun Screen #4
1=ZONE
Noun Screen #8
61
Advertisement
Table of Contents
