Honeywell Notifier NFW-100X Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Control Panel
  5. NOTIFIER NFW-100X
  6. Manual

Honeywell Notifier NFW-100X Manual

Addressable fire alarm control panel
Hide thumbs Also See for Notifier NFW-100X:
Table of Contents

Advertisement

Quick Links

Download this manual
Addressable Fire Alarm Control Panel
NFW-100X
Manual
Document LS10131-001NF-E Rev: C
7/25/2018 ECN: 18-323

Advertisement

Table of Contents
loading

Related Manuals for Honeywell Notifier NFW-100X

Summary of Contents for Honeywell Notifier NFW-100X

  • Page 1 Addressable Fire Alarm Control Panel NFW-100X Manual Document LS10131-001NF-E Rev: C 7/25/2018 ECN: 18-323...
  • Page 2 Fire Alarm & Emergency Communication System Limitations While a life safety system may lower insurance rates, it is not a substitute for life and property insurance! An automatic fire alarm system—typically made up of smoke Heat detectors do not sense particles of combustion and alarm detectors, heat detectors, manual pull stations, audible warning only when heat on their sensors increases at a predetermined rate devices, and a fire alarm control panel (FACP) with remote notifica-...
  • Page 3 HARSH™, NIS™, and NOTI•FIRE•NET™ are all trademarks; and Acclimate® Plus™, eVance®, FlashScan®, FAAST Fire Alarm Aspiration Sensing Technology®, Honeywell®, Intelligent FAAST®, NOTIFIER®, ONYX®, ONYXWorks®, SWIFT®, VeriFire®, and VIEW® are all registered trademarks of Honeywell International Inc. Microsoft® and Windows® are registered trademarks of the Microsoft Corporation. Chrome™ and Google™ are trademarks of Google Inc. Firefox® is a registered trademark of The Mozilla Foundation.
  • Page 4 Brief description of content you think should be improved or corrected • Your suggestion for how to correct/improve documentation Send email messages to: FireSystems.TechPubs@honeywell.com Please note this email address is for documentation feedback only. If you have any technical issues, please contact Technical Services. NFW-100X Manual — P/N LS10131-001NF-E:C 7/25/2018...

  • Page 5: Table Of Contents

    Table of Contents Section 1: Product Description ............................13 1.1: Features and Options .......................................13 1.2: Specifications........................................14 1.3: Controls and Indicators....................................16 1.4: Components ........................................16 1.4.1: Intelligent Addressable Detectors.................................17 1.4.2: Intelligent Addressable Modules ................................17 1.4.3: Addressable Device Accessories ................................17 End-of-Line Resistor Assembly................................17 Power Supervision Relay..................................17 EOL-C(R/W) Mounting Plate.................................17 1.5: Optional Modules ......................................17...
  • Page 6 Table of Contents ANN-BUS Device Addressing ................................36 N-ANN-80 Remote Fire Annunciator ..............................36 N-ANN-100 Remote Fire Annunciator ..............................38 N-ANN-S/PG Serial/Parallel Interface Module .............................39 N-ANN-I/O LED Driver Module ................................41 N-ANN-LED Annunciator Module ................................43 N-ANN-RLY Annunciator Module................................45 2.8.5: Printer ........................................46 Printer Configuration ....................................46 2.8.6: NFC-FFT Firefighter Telephone ................................47 2.8.7: FWSG Wireless Gateway ..................................47 2.9: Automatic Audio Panel Control..................................47...
  • Page 7 Table of Contents Trouble Report Limit (Dialer Runaway Prevention) ..........................86 Report Style ......................................87 Event Codes ......................................87 3.6.8: Annunciators......................................90 ANN-BUS Setup....................................90 ANN-BUS Options ....................................97 3.6.9: Password Change....................................99 Invalid Password.....................................99 3.6.10: Clear Program....................................100 3.6.11: Program Check ....................................100 3.7: Maintenance Programming Level..................................101 3.7.1: Disable Point.......................................101 3.7.2: History ........................................102 3.7.3: Program Check ....................................102 3.7.4: Walktest ......................................103...
  • Page 8 Table of Contents 4.24.9: Annunciators.....................................117 4.24.10: Communicator ....................................117 4.24.11: Print.........................................118 Chamber Value .....................................119 Drift Compensation....................................119 Maintenance Alert....................................119 4.24.12: Time-Date .......................................120 4.24.13: Battery Charger....................................120 4.24.14: 4XTM Supervision ..................................120 4.24.15: Remote Sync....................................120 Section 5: Central Station Communications - POTS Transmission ................. 121 5.1: Transmittal Priorities .....................................121 Section 6: FS-Tools Upload/Download........................
  • Page 9 Table of Contents Slide-in Labels ................................159 NFW-100X Series Fire Alarm Control Panel Operating Instructions ..............................161 NFW-100X Manual — P/N LS10131-001NF-E:C 7/25/2018...
  • Page 10 It is imperative that the installer understand the requirements of the Authority Having Jurisdiction (AHJ) and be familiar with the stan- dards set forth by the following regulatory agencies: • Underwriters Laboratories • National Fire Protection Association Before proceeding, the installer should be familiar with the following documents. NFPA Standards NFPA 72 National Fire Alarm Code NFPA 70 National Electrical Code...
  • Page 11 250V ES50- PCA REV ES200- PCA REV NFW-100X Manual — P/N LS10131-001NF-E:C 7/25/2018...
  • Page 12 Peripheral Devices and Their Documents: ANN Audio Control for NFC-50/100 Doc. #LS10001-001NF-E N-ANN-RLY N-ANN-S/PG N-ANN-100 N-ANN-I/O Relay Card N-ANN-80 Printer Driver LCD Text Annunciator N-ANN-(R)LED LED Driver Doc. #53318 LCD Text Annunciator Doc. #151424 Doc. #LS10205-001NF-E LED Display Doc. #151243 Doc.

  • Page 13: Section 1: Product Description

    Section 1: Product Description The NOTIFIER NFW-100X is an addressable FACP (Fire Alarm Control Panel) with a pre-installed communicator card that is compact, cost effective, intelligent, and has an extensive list of powerful features which offers the latest in fire protection technology. The power supply and all electronics are housed in a metal cabinet, providing a complete fire control system for most applications.

  • Page 14: Specifications

    Product Description Specifications  N-ANN-100 (FM only)  N-ANN-I/O LED Driver  N-ANN-S/PG Printer Module  N-ANN-RLY Form-C Relay Module  N-ANN-LED Annunciator Module annunciates alarm, trouble and supervisory (required for emergency signaling)  N-ANN-RLED Annunciator Module annunciates alarms only •...
  • Page 15 Specifications Product Description Remote Sync Output - TB8 Remote power supply synchronization output 24 VDC nominal special application power Maximum current is 350 mA End-of-Line Resistor: 4.7KΩ Output linked to NAC 1 control Supervised and power-limited circuit Programmable Class A or Class B wiring Secondary ANN-BUS - TB10 ANN-BUS annunciator connector, Terminal 1 (+/A) and Terminal 2 (-/B) Annunciators require non-resettable power...

  • Page 16: Controls And Indicators

    Product Description Controls and Indicators 1.3 Controls and Indicators LCD Display The FACP uses an 80-character (4 lines X 20 characters) high viewing angle LCD display. The display includes a long life LED backlight that remains illuminated. If AC power is lost and the system is not in alarm, SYSTEM NORMAL the LED backlight will turn off to conserve batteries.

  • Page 17: 1: Intelligent Addressable Detectors

    Optional Modules Product Description ® • Dialing the Central Station(s) number: default is Touch-Tone , programmable to rotary • For tone burst or touchtone type formats: discern proper Ack and Kissoff tone(s). The frequency and time duration of the tone(s) varies with the transmission format.

  • Page 18: Accessories

    Product Description Accessories 1.6 Accessories 1.6.1 FS-Tools Programming Utility The FS-Tools Programming Utility can be used to locally or remotely program the FACP from most Windows® compatible computers (PC), running Windows 7 or newer, 32 or 64 bit. The FACP program files can also be created and stored on the PC for future download to the control panel.

  • Page 19: 6: Nfc-50/100

    Accessories Product Description 1.6.6 NFC-50/100 The NFC-50/100 is a single channel, 50 watt, 25 V , emergency voice evacuation panel that may be used for fire applications, mass notification applications, or both. Automatic activation of the NFC-50/100 is possible via eight Command Input Circuits (CMD) or via the ANN BUS serial communications link from the NFW-100X FACP.

  • Page 20: N-Ann-Led Annunciator Module

    Before connecting the control panel to the public switched telephone network, the installation of two RJ31X jacks is necessary. If trouble is experienced with this equipment, for repair or warranty information, please contact: Manufacturer: Honeywell International, Inc. 12 Clintonville Road Northford, CT 06472...

  • Page 21: 2: Telephone Company Rights And Warnings

    Telephone Requirements and Warnings Product Description 1.8.2 Telephone Company Rights and Warnings The telephone company, under certain circumstances, may temporarily discontinue services and/or make changes in its facilities, ser- vices, equipment or procedures which may affect the operation of this control panel. However, the telephone company is required to give advance notice of such changes or interruptions.

  • Page 22: Section 2: Installation

    Section 2: Installation The cabinet may be either semi-flush or surface mounted. The cabinet mounts using two key slots and two 0.250” (6.35 mm) diameter holes located in the backbox. The key slots are located at the top of the backbox and the two securing holes at the bottom. Carefully unpack the system and check for shipping damage.
  • Page 23 Mounting the Backbox Installation Semi-Flush Mounting Do not recess box more Hinge Slot for optional than 3.875” into wall to Dress Panel avoid covering venting holes on top of box. Mounting slots for optional Trim Ring Semi-flush mounting hole Hinge Slot for optional Dress Panel Figure 2.2 NFW-100X Cabinet Mounting NFW-100X Manual —...
  • Page 24 Installation Mounting the Backbox 5.207” (13.23cm) 16.822” (42.73 cm) 6.537” (16.6cm) Width Depth Height 19.26” (48.92 cm) Right Side Left Side Bottom Figure 2.3 NFW-100X Cabinet Dimensions An optional Trim Ring (P/N TR-CE-B) is also available for semi-flush mount installations. NFW-100X Manual —...

  • Page 25: Power

    Power Installation 2.2 Power WARNING: RISK OF EQUIPMENT DAMAGE AND PERSONAL INJURY SEVERAL DIFFERENT SOURCES OF POWER CAN BE CONNECTED TO THIS PANEL. DISCONNECT ALL SOURCES OF POWER BEFORE SERVICING. THE PANEL AND ASSOCIATED EQUIPMENT MAY BE DAMAGED BY REMOVING AND/OR INSERTING CARDS, MODULES OR INTERCONNECTING CABLES WHILE THIS UNIT IS ENERGIZED.

  • Page 26: 3: Special Application Dc Power Output Connection

    Installation Relays 2.2.3 Special Application DC Power Output Connection All Special Application DC power outputs are power-limited (refer to “UL Power-limited Wiring Requirements” on page 29). Power-limited Resettable or Non-resettable Power Power-limited Non-resettable or Resettable Power 1.0 amperes max., 24 VDC nominal filtered, programmable 1.0 amperes max., 24 VDC nominal filtered, non- resettable or non-resettable power can be drawn from TB11 resettable or resettable power is programmable.

  • Page 27: 1: Class B Nac Wiring

    Notification Appliance Circuits Installation 2.4.1 Class B NAC Wiring 4 Class B Notification Appliance Circuits, supervised and power-limited - 4.7 kΩ, ½ watt P/N:71252 UL listed NAC 3 NAC 1 NAC 4 NAC 2 Polarized Bells Polarized Bells Polarized Strobes Polarized Strobes Polarized Horns Polarized Horns...

  • Page 28: Remote Synchronization Output

    Installation Remote Synchronization Output 2.5 Remote Synchronization Output Synchronization is a feature that controls the activation of notification appliances in such a way that all devices will turn on and off at exactly the same time. This is particularly critical when activating strobes which must be synchronized to avoid random activation and a potential hazard to individuals.

  • Page 29: Ul Power-Limited Wiring Requirements

    UL Power-limited Wiring Requirements Installation 2.6 UL Power-limited Wiring Requirements Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” (6.35 mm) away from any nonpower-limited circuit wiring and nonpower-limited circuit wiring must enter and exit the cabi- net through different knockouts and/or conduits.

  • Page 30: Ipots-Com Communicator

    Installation IPOTS-COM Communicator 2.7 IPOTS-COM Communicator Two independent telephone lines can be connected to the control panel via the IPOTS-COM Phone/IP Communication Module. Tele- phone line control/command is made possible via double line seizure as well as usage of an RJ31X style interconnection. Note that it is critical that the IPOTS-COM Digital Communicator be located as the first device on the incoming telephone circuit to properly function.

  • Page 31: Dip Switches

    SW2: 6-position dip switch- FUTURE USE- No configuration necessary. • SW3: 2-position dip switch- Factory Settings- Do not change unless instructed to do so by Honeywell. 2.8 Optional Module Installation WARNING: RISK OF ELECTRIC SHOCK AND EQUIPMENT DAMAGE DISCONNECT ALL SOURCES OF POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY MODULES OR WIRING.
  • Page 32 Installation Optional Module Installation Local Energy Municipal Box Service (NFPA 72 Auxiliary Fire Alarm Systems): Supervisory Current: 5.0 mA Trip Current: 350 mA (subtracted from notification appliance power) Coil Voltage: 3.65 VDC Maximum Coil Resistance: 14.6 ohms Maximum allowable wire resistance between panel and trip coil: 3 ohms Municipal Box wiring can leave the building Remote Station Service (NFPA 72 Remote Station Fire Alarm Systems) - Intended for connection to a polarity reversal circuit or a Remote Station receiving unit having compatible ratings:...

  • Page 33: 4: Ann-Bus Annunciators/Modules

    Optional Module Installation Installation Standoff ALRM TRBL SUPV RMT SYNC NAC1 OUT+ RTN+ RTN- OUT- J12 & J13 Connectors Jumper JS3 Standoff 4XTM FACP main circuit board Figure 2.16 4XTM Connectors to NFW-100X Connectors NOTE: When a 4XTM is installed, enable supervision in panel programming. Jumper JS3 on the FACP main circuit board can be used to configure the FACP supervisory relay for operation with the 4XTM module.
  • Page 34 Installation Optional Module Installation In general, the wire length is limited by resistance, but for heavier wire gauges, capacitance is the limiting factor. Maximum length can never be more than 6,000 feet (1,800 m), regardless of gauge used. The following formulas were used to generate the wire distances: 2.0 Volts Maximum Resistance (Ohms) Total Worst Case Current Draw (amps)
  • Page 35 Optional Module Installation Installation Figure 2.18 illustrates the wiring between the FACP’s Secondary ANN-BUS and ANN-BUS devices. ANN-BUS and power wiring are supervised and power-limited 4 3 2 1 ANN-BUS Device Secondary 24 VDC ANN-BUS nonresettable NFW-100X Figure 2.18 Secondary ANN-BUS wiring to ANN-BUS Device ...

  • Page 36: Ann-Bus Device Addressing

    Installation Optional Module Installation ANN-BUS Device Addressing Each ANN-BUS device requires a unique address (ID Number) in order to communicate with the FACP. A 5-position DIP switch on each device is used to set this address. The address set for these devices must also be programmed at the FACP for the specific device (refer to the programming section titled “ANN-BUS Setup”...
  • Page 37 Optional Module Installation Installation  Mounting The N-ANN-80 can be surface or semi-flush mounted to a single, double or 4” square electrical box. Select and remove the appropriate knockout(s), pull the necessary wires through the knockouts and mount the annunciator in or on the wall depending on the type of instal- lation desired.

  • Page 38: N-Ann-100 Remote Fire Annunciator

    Installation Optional Module Installation After all connections are made, remove extra wire from inside of annunciator by dressing it neatly through wire channel, with any excess wire pushed back through hole into electrical box ANN-BUS and power wiring are supervised and power-limited 4 3 2 1 ANN-BUS Device Primary...

  • Page 39: N-Ann-S/Pg Serial/Parallel Interface Module

    Optional Module Installation Installation  Programming Following installation and wiring of the N-ANN-100 LCD annunciator to the FACP, the annunciator must be added to the system via FACP programming. Refer to the programming section titled “ANN-BUS Setup” on page 90 in this manual for detailed programming information.
  • Page 40 Installation Optional Module Installation  Setting Printer Options Refer to the documentation supplied with the PRN-7 printer for instructions on using the printer menu controls. Set the printer options (under the menu area) as shown in the following table: Option Setting Option Setting...

  • Page 41: N-Ann-I/O Led Driver Module

    Optional Module Installation Installation ANN-I/O LED Driver Module  ANN-I/O Board Layout Figure 2.22 illustrates the N-ANN-I/O board showing locations of screw terminals for connection to the FACP, pin connectors for con- necting LEDs and the DIP switch for selecting the ANN-BUS ID number. LED Out LED Out LED Out...
  • Page 42 Installation Optional Module Installation  ANN-I/O Connection to FACP The N-ANN-I/O connects to the FACP via the ANN-BUS as illustrated in Figure 2.23. After the N-ANN-I/O is connected to the panel, it must be added to the system via FACP programming. Refer to the section titled “ANN-I/O Options” on page 91. 20 21 LED Out LED Out...

  • Page 43: N-Ann-Led Annunciator Module

    Optional Module Installation Installation Pin # LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Cathode LED9 LEDs LED10 LED Power Anode no connection Pin # LED11 LED12 LED13 LED14 LED15 LED16 LED17 LED18 Cathode LED19 LEDs LED20 Anode LED Power no connection Figure 2.24 ANN-I/O LED Wiring N-ANN-LED Annunciator Module...
  • Page 44 Installation Optional Module Installation  Specifications • Max. ANN-BUS Voltage: 24 VDC • Max. Current:  Alarm: 68 mA  Standby: 28 mA • Operating Temperature: 32°F to 120°F (0°C to 49°C) • For indoor use in a dry location only ...

  • Page 45: N-Ann-Rly Annunciator Module

    Optional Module Installation Installation ANN-RLY Annunciator Module  Specifications • Operating Voltage: 24 VDC • Max. Current:  Alarm: 75 mA  Standby: 15 mA • Operating Temperature: 32°F to 120°F (0°C to 49°C) • For indoor use in a dry location only ...

  • Page 46: 5: Printer

    Installation Optional Module Installation  N-ANN-RLY Board Layout and Connection to FACP Figure 2.29 illustrates the N-ANN-RLY board showing locations of screw terminals for connection to the FACP and the DIP switches for selecting the ANN-BUS ID number. ANN-BUS (ID#) Address DIP switch 1 2 3 4 5 6 7 8 ANN-BUS and power wiring are...

  • Page 47: 6: Nfc-Fft Firefighter Telephone

    Automatic Audio Panel Control Installation 2.8.6 NFC-FFT Firefighter Telephone The NFC-FFT connects from TB11 (non-resettable aux power) on the FACP to the DC Power input on the NFC-FFT board. NFC-FFT NFW-100X Figure 2.30 NFC-FFT Connections 2.8.7 FWSG Wireless Gateway The FWSG connects to the FACP’s SLC connection at TB10. The FWSG can be powered by either the SLC or an external 24 VDC power source.
  • Page 48 Installation Automatic Audio Panel Control (1 of 5 using the legacy NFV panel) can be generated over the selected speaker circuit. Any fault in the NFC-50/100 audio system is sent to the FACP via the FACP Data Bus and is indicated as an annunciator fault on the FACP display. A fault at the NFV-25/50ZS Series panel will cause the FACP to indicate a System Trouble and the display will indicate a Voice Evac Fault.

  • Page 49: Section 3: Programming

    Section 3: Programming NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTION AND OTHER INVOLVED PARTIES This product incorporates field-programmable software. In order for the product to comply with the requirements in the Standard for Control Units and Accessories for Fire Alarm Systems, UL 864, certain programming features or options must be limited to specific values or not used at all as indicated below: Program feature or Permitted in...

  • Page 50: User Programming

    Programming User Programming RECALL Insert A - Z A - Z 0 - 9 0 - 9 ■ (on YZ key) Space bar — — • •         ENTER Enter ACK/STEP SILENCE DRILL RESET 3.2 User Programming The NFW-100X is completely field programmable and requires no special software skills.

  • Page 51: Initial Power-Up

    Initial Power-up Programming Pressing 3 will select Upload/Download via FS-Tools which allows the user to enable the remote programming option. Refer to “FS- Tools Upload/Download” on page 123. Pressing 4 will select USB Up/Download which allows the user to upload or download FACP programming via the USB port. See “USB Upload/Download”...

  • Page 52: Master Programming Level

    Programming Master Programming Level To access user Programming mode, press the Enter or Mode key. The LCD will display the following. 1=READ STATUS MODE 2=PROGRAMMING MODE 3=FS-TOOL UP/DOWNLD 4=USB UP/DOWNLOAD To enter the user Programming mode, press 2. The display will read as follows: PROGRAMMING ENTER PASSWORD ...

  • Page 53: 2=Point Program

    Master Programming Level Programming When Autoprogramming is completed, the control panel will display the type and quantity of each device installed on the SLC loop sim- ilar to the following display: # OF DET LOOP1 055 # OF MON LOOP1 035 # OF CON LOOP1 030 Autoprogram Result Screen #1 In the preceding example, the display indicates that the SLC Loop has 55 addressable detectors, 35 monitor modules and 30 control...
  • Page 54 Programming Master Programming Level NOTE: The system must be monitored by a Supervising Station when using carbon monoxide detection per The Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 720. The programmer can continue adding detectors by pressing the ESC key which will return the display to the Add Detector Screen. ...
  • Page 55 Master Programming Level Programming  Normal - indicates that the detector with the selected address is physically installed on the SLC and communicating with the control panel (enabled)  <ADJ><NOUN> - represents the adjective and noun, which have been programmed, describing the location of the displayed device ...
  • Page 56 Programming Master Programming Level While viewing either Detector Type screen, select the type of detector being programmed by pressing the corresponding keyboard num- ber key. The display will return to Edit Detector Screen #2 and indicate the selection next to the Type option. NOTE: If a detector is selected to be a DUCT SUPERV type, it will function like a supervisory point not a fire alarm point.
  • Page 57 Master Programming Level Programming With the preceding program settings, when the detector with address 005 is activated, zone Z98 will cause its associated control module to activate immediately, sounding the connected signaling device to indicate the Pre-signal condition. Following the Pre-signal delay time, zone Z001 will cause its associated control module to activate and the control panel will initiate an alarm condition.
  • Page 58 Programming Master Programming Level The sounder base volume has two settings: Low or High. Press 1 while viewing Sounder Base Screen #2 SOUNDER BASE 1=ZONE ASSIGNMENT until the display reads Low or High as desired. Each press of the 1 key will cause the display to toggle 000 000 000 000 000 between Volume Low and Volume High.
  • Page 59 Master Programming Level Programming Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. 1=STANDARD ADJECTIVE 2=STANDARD NOUN Note that the keyboard down arrow key must be pressed to see all the Noun screens. Press the number corre- 3=CUSTOM ADJECTIVE sponding to the noun that is to be used as a descriptor for the location of the detector currently being pro- 4=CUSTOM NOUN...

  • Page 60: Module Programming

    Programming Master Programming Level Module Programming Pressing 2, while viewing Point Program Screen #2, will allow the programmer to add, delete or change the POINT PROGRAM SELECT TYPE programming of an addressable module. The following screen will be displayed by the control panel: 1=DETECTOR 2=MODULE MODULES...
  • Page 61 Master Programming Level Programming A flashing cursor will appear in the position of the first asterisk to the left. The programmer keys in the three digit module address, such as 012. When the last digit is keyed-in, if the selected address has not been added to programming, a screen showing information about a device that is installed with a lower address, closest to the selected address, will be displayed.
  • Page 62 Programming Master Programming Level Type Monitor Using the FS-Tools Upload/Download utility, unique user-defined monitor types can be created and loaded EDIT MONITOR 1=ENABLED into the FACP for later use. The FACP response to the activation of a user-defined type is the same as most 2=TYPE MONITOR previous standard types in the list, thus allowing a variety of user-defined types and responses.
  • Page 63 Master Programming Level Programming Ack Switch Acts like panel Acknowledge Key Sil Switch Acts like panel Silence Key Reset Switch Acts like panel Reset Key Drill Switch Acts like panel Drill Key PAS Bypass PAS Disable HVAC RESTART Switch (see note 2) Drill Switch AR Acts like panel Drill Key, nonlatching (tracking) Wireless Gateway...
  • Page 64 Programming Master Programming Level Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. 1=STANDARD ADJECTIVE 2=STANDARD NOUN Note that the keyboard down arrow key must be pressed to see all the Adjective screens. Press the number 3=CUSTOM ADJECTIVE corresponding to the adjective that is to be used as a descriptor for the location of the monitor module cur- 4=CUSTOM NOUN...
  • Page 65 Master Programming Level Programming As an example, the user could quickly enter ‘FLR_3_ROOM 305’ as follows: The cursor is on the first letter of the Adjective field. Press the zero key twice to display FLR_3 With the cursor on the first letter of the Noun field, press the zero key twice to recall the display ROOM_304. The cursor automatically jumps from the first to the last letter of the Noun field With the cursor on the last letter of the Noun field, press the zero key again to increment the room number to 305 Press the right arrow key to advance the zone field...
  • Page 66 Programming Master Programming Level While viewing one of the Control Type screens, select the type of control module being programmed by pressing the corresponding key- pad number key. The display will return to the Edit Control Screen #2 and indicate the new type selection. NOTE: A control relay module set to the Resettable Power type will follow the main circuit board 24 VDC resettable power unless the control relay module is disabled.
  • Page 67 Master Programming Level Programming Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. 1=STANDARD ADJECTIVE 2=STANDARD NOUN Note that the keyboard down arrow key must be pressed to see all the Adjective screens. Press the number 3=CUSTOM ADJECTIVE corresponding to the adjective that is to be used as a descriptor for the location of the control module cur- 4=CUSTOM NOUN...

  • Page 68: 3=Zone Setup

    Programming Master Programming Level • The above increment function may be repeated with each press of the zero key. As an example, the user could quickly enter ‘FLR_3_ROOM 305’ as follows: The cursor is on the first letter of the Adjective field. Press the zero key twice to display F.LR_3 With the cursor on the first letter of the Noun field, press the zero key twice to recall the display ROOM_304.

  • Page 69: Special Purpose Zone

    Master Programming Level Programming Special Purpose Zone Pressing 3 for Special Purpose, while viewing Zone Setup Screen #1, will display the following screens: SPECIAL PURPOSE SPECIAL PURPOSE 1=PAS 97 1=LOCAL ALM 96 2=PRESIGNAL 98 3=TWO STAGE 99 Special Purpose Zone Screen #1 Special Purpose Zone Screen #2 Zones 097, 098, 099, and 096 can be programmed for normal zone operation or for special purpose applications.

  • Page 70: Zone Type

    Programming Master Programming Level This display will show all of the zones that are disabled in the control panel. Note that an up and/or down arrow may appear in the upper right corner of the display, indicating that additional screens of zone information exists. Press the up or down arrow keys to view the additional zones.

  • Page 71: 4: Loop Setup

    Master Programming Level Programming Pressing the down arrow key will display additional screens for Zones up to Z99. Press the number key corresponding to the Zone to be programmed. Screens will be displayed allowing the programmer to select Audio Messages 1 through 14. When an audio message is selected, the display will return to the Zone Message screen, showing the message selected for that particular zone.

  • Page 72: Function Keys

    Programming Master Programming Level • Remote Sync Enable: This feature controls the activation of notification appliances in such a way that all devices will turn on and off at exactly the same time. Pressing 2 for System Setup, while viewing Programming Screen #2, will cause the following screens to be PROGRAMMING 1=LOOP SETUP displayed:...

  • Page 73: Time-Date

    Master Programming Level Programming Pressing 1 while viewing the Banner Screen will select the blank factory default banner setting and display BANNER the following screen: 1=FACTORY 2=USER DEFINED FACTORY BANNER Banner Screen Factory Banner Pressing the Enter key will store this selection in nonvolatile memory and return the display to the Banner Screen. Pressing 2 while viewing the Banner Screen will cause the following screens to be displayed: USER DEFINED BANNER USER BANNER - LINE 2...

  • Page 74: Timers

    Programming Master Programming Level  Clock Format The clock can be configured to display 12 hour (AM & PM) or 24 hour (military) time. Pressing 3 while viewing the Time-Date screen will cause the display to toggle between 12HR and 24HR. Select 12HR for 12 hour display or 24HR for 24 hour display.Note: NOTE: If the clock is changed to 24 hour (military) format, the date will change to the European standard of Day-Month-Year (for display purposes only).

  • Page 75: Nac (Notification Appliance Circuit)

    Master Programming Level Programming Note that the FACP allows programming for PAS and Pre-signal timers, but a detector can only be programmed for either PAS or Pre- signal operation. Refer to“Edit Detector” on page 54 for programming details.  Waterflow Delay A delay can be added prior to declaring a waterflow type of alarm.
  • Page 76 Programming Master Programming Level The Notification Appliance Circuits can be configured independently by pressing 1 for NAC 1, 2 for NAC 2, 3 for NAC 3, or 4 for NAC The following screens will be displayed for each selection: NAC # NAC # NAC # NAC #...
  • Page 77 Master Programming Level Programming To disable the Auto Silence feature, press 1 for No while viewing Auto Silence Screen #1. To enable the Auto Silence feature, press the number corresponding to the time delay which will elapse before Auto Silence activates. This information will be stored in memory and the display will return to NAC Screen #2.

  • Page 78: Relays

    Programming Master Programming Level remaining zones can be left blank or programmed as general alarm zone Z000. When all desired changes have been made, press the Enter key to store the zone assignments. The display will return to the NAC Screen #3 which will show the zone assignments just entered.

  • Page 79: Canadian Option

    Master Programming Level Programming While viewing the selected screen, press the number corresponding to the desired relay type to program the main circuit board relay. The choice will be stored in memory and the display will return to the Relay Type Screen which will show the programmed type choice. Press the Escape key to return to the Relays Selection Screen and repeat the preceding procedure for the remaining relays.

  • Page 80: Trouble Reminder

    Programming Master Programming Level Select the desired output. The following screen will be displayed. AUX 1 1=CLASS A 2=RESETTABLE Each output can be programmed as resettable or non-resettable power. Non-resettable power is suitable for powering annunciators while resettable power is suitable for powering smoke detectors. Each press of the 2 key will cause the display to toggle between Resettable Yes and Resettable No.

  • Page 81: View Events

    Master Programming Level Programming View Events Pressing 1 while viewing the History Screen will allow the user to select the events to be viewed as illus- HISTORY trated in the following: 1=VIEW EVENTS 2=ERASE HISTORY HISTORY History Screen 1=VIEW ALL 2=VIEW ALARMS 3=VIEW OTHER EVENTS View Events Screen...

  • Page 82: Ip Settings

    Programming Master Programming Level  POTS Line (X) If telephone lines are connected to the IPOTS-COM board at J4 (Line 1) and J5 (Line 2), their settings can be configured by pressing 1 or 2, respectively. Pressing 1 or 2 will display the following screen. The programming options for Line 1 and Line 2 are identical. POTS LINE X 1=ENABLED 2=TYPE...

  • Page 83: Primary And Secondary Communication Paths

    Master Programming Level Programming  DHCP Enabled If the internet router used by the IPOTS-COM is configured for DHCP (Dynamic Host Configuration Protocol) where addresses are automatically assigned, press 1 while viewing the IP Settings Screen to change the display to Enabled Yes. Each press of the 1 key will cause the display to toggle between Enabled Yes and Enabled No.
  • Page 84 Programming Master Programming Level Note that the following information must be entered for both the Primary and Secondary Communication Paths. XXX COMM PATH 1=POTS 2=ETHERNET 3=CELLULAR Comm Path Screen  POTS To configure the communication method to contact central station as a telephone line, select 1 for POTS. XXX COMM PATH 1=POTS The following screens will display.
  • Page 85 Master Programming Level Programming Select the Communication Format by pressing the corresponding number key while viewing the Comm Format screen. The following table describes each format: Screen Selection Communication Format Description ADEMCO CONTACT ID Contact ID, DTMF, 1400/2300 ACK SIA 8 Security Industry Association, 8 messages per call SIA 20 Security Industry Association, 20 messages per call...

  • Page 86: Trouble Report Limit (Dialer Runaway Prevention)

    Programming Master Programming Level • NFPA 2010 Dual Path: Supervision Interval: 24 Hours • NFPA 2010 Sole Path: Supervision Interval: 5 min • NFPA 2013 Dual Path: Supervision Interval: 6 Hours • NFPA 2013 Sole Path: Supervision Interval: 1 Hour NOTE: These supervision settings apply to both the Cellular settings and the Ethernet settings.

  • Page 87: Report Style

    Master Programming Level Programming Report Style Pressing 1 while viewing Communicator Screen #3 will cause the Report Style display to toggle between COMMUNICATOR 1=REPORT STYLE POINT Point and Zone. Setting the Report Style to Point will program the Communicator to report individual point 2=EVENT CODES status to the Central Station.
  • Page 88 Programming Master Programming Level DUCT SUPERVISORY Zone Point DET-USER-DEF-7 Zone Point PHOTO SUPER AR Zone Point DET-USER-DEF-8 Zone Point CO SUPERVISORY Zone Point DET-USER-DEF-9 Zone Point PHOTO ADAPT Zone Point DET-USER-DEF-10 Zone Point PHOTO BEAM Zone Point DET-USER-DEF-11 Zone Point MONITOR Zone Point...
  • Page 89 Master Programming Level Programming SLC 1 GND FAULT NEG SLC 1 COMM FAULT SLC 1 OPEN FAULT SLC 1 SHORT FAULT GROUND FAULT LOW BATTERY NO_BATTERY TELCO LINE 1 TELCO LINE 2 COMM FAULT 1 COMM FAULT 2 TOTAL COMM FAULT ETHERNET FAULT CELLULAR FAULT PRINTER FAULT...

  • Page 90: 8: Annunciators

    Programming Master Programming Level 3.6.8 Annunciators Pressing 3 while viewing Programming Screen #3 will cause the control panel to display the following PROGRAMMING 1=HISTORY screens: 2=COMMUNICATOR 3=ANNUNCIATORS ANN-BUS SELECT 1=PRIMARY Programming Screen #3 2=SECONDARY 3=ANN-BUS OPTIONS A printer module, graphic annunciator module, LCD annunciator module, LED annunciator module, and relay module can be pro- grammed into the NFW-100X system.
  • Page 91 Master Programming Level Programming If ANN-I/O, ANN-LED, or ANN-RLY is the selected module type, the following ANN-BUS Address Screen will be displayed: ANN-BUS MODULE X-1 ANN-BUS ADDRESS 1=TYPE ANN-I/O 2=MODULE OPTIONS ANN-BUS Address Screen Since the options for each of these module types can be individually set, pressing 2 for Module Options, while viewing the ANN-BUS Address Screen will display the available options as described below.
  • Page 92 Programming Master Programming Level ANN-I/O Zone Option If Zone is selected as the module option, the first ten LEDs on the first N-ANN-I/O module will display the system status information. The remaining 30 LEDs on the first module and 40 LEDs on the remaining modules will display the active/alarm status of each zone in the Zone Range programmed for that particular module.
  • Page 93 Master Programming Level Programming ANN-I/O Point Option If Point is selected as the module option, the first ten LEDs on the first N-ANN-I/O module will display the system status information. The remaining 30 LEDs on the first module and 40 LEDs on each additional module will display the active/alarm status of each point in the Point Range programmed for that particular module.
  • Page 94 Programming Master Programming Level ANN-LED Options Pressing 2 for Module Options while viewing the (XXX) ANN-BUS Address Screen when the ANN-LED ANN XXX 1=ENABLED option is selected, will display the following screen: 2=MODULES INSTALLED 3=AUTO-CONFIGURE ANN-LED - ADDR X-1 ANN-LED - ADDR X-1 ANN-LED - ADDR X-1 ANN XXX Screen #2 1=POINT/ZONE...
  • Page 95 Master Programming Level Programming ANN-LED Zone Option - Alarm, Trouble and Supervisory If Zone is selected as the module option, and the module is programmed to annunciate alarms, troubles and supervisories, the first ten LEDs on the first N-ANN-LED module will display the system status information. The remaining 30 LEDs on the first module and the last 30 LEDs on the remaining modules will display the alarm, trouble and supervisory status for each of the ten zones in the Zone Range programmed for that particular module.
  • Page 96 Programming Master Programming Level Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Point 031 Point 032 Point 033 Point 034 Point 035 Active/Alarm Active/Alarm Active/Alarm Active/Alarm Active/Alarm Point 036 Point 037 Point 038 Point 039...

  • Page 97: Ann-Bus Options

    Master Programming Level Programming ANN-RLY Options Pressing 2 for Module Options while viewing the ANN-BUS Address Screen when the ANN-RLY option is ANN XXX 1=ENABLED selected, will cause the following screen to be displayed: 2=MODULES INSTALLED 3=AUTO-CONFIGURE ANN-RLY - ADDR. X-1 ANN XXX Screen #2 1=RLY 1 ZONE 000...
  • Page 98 Programming Master Programming Level  ANN-S/PG (Print) Options The Print option allows the programmer to configure the optional printer. Pressing 1 while viewing the XXX ANN-BUS 1=ANN-S/PG OPTIONS ANN-BUS screen will display the following screens: 2=ANN-LED OPTIONS 3=ANN-80/100 OPTIONS ANN-S/PG OPTIONS ANN-S/PG OPTIONS ANN-S/PG OPTIONS 1=PORT...

  • Page 99: 9: Password Change

    Master Programming Level Programming The Lock Enable option allows the programmer to select whether or not any installed N-ANN-80 or N-ANN-100 annunciator must be unlocked by its key before any annunciator key presses will function. Pressing 2 while viewing the ANN-80/100 Options Screen #1 causes the display to toggle between Lock Enable Yes (annunciator must be unlocked for keys to function) and Lock Enable No (lock position is ignored).

  • Page 100: 10: Clear Program

    Programming Master Programming Level 3.6.10 Clear Program Pressing 2 while viewing Programming Screen #4, will select the Clear Program option. This will cause the PROGRAMMING 1=PASSWORD CHANGE LCD to display the following screen: 2=CLEAR PROGRAM 3=PROGRAM CHECK CLEAR PROGRAM 1=WHOLE SYSTEM Programming Screen #4 2=ALL POINTS Clear Program Screen...

  • Page 101: Maintenance Programming Level

    Maintenance Programming Level Programming The Zone No Output feature allows the programmer to view the zones which have not been programmed to at least one output device (not including general alarm Zone 00). The example in the preceding screen indicates that Zones 05, 07, 09, 10 and 11 have been pro- grammed to an addressable detector with an address of 001 on loop 1 but have not been programmed to any output devices.

  • Page 102: 2=History

    Programming Maintenance Programming Level 3.7.2 History Pressing 2 while viewing Maintenance Screen #1 will cause the following screen to be displayed: PROGRAMMING 1=POINT PROGRAM HISTORY 2=HISTORY 3=PROGRAM CHECK 1=VIEW EVENTS 2=ERASE HISTORY Maintenance Screen #1 History Screen The History feature allows the operator to view control panel events which have been stored in a history file in memory and erase the contents of the history file Pressing 1 while viewing the History screen will cause the following screen to be displayed: HISTORY...

  • Page 103: 4: Walktest

    Maintenance Programming Level Programming Pressing 3 while viewing Program Check screen will cause a screen similar to the following to be displayed: ZONES NO OUTPUT 005 007 009 010 011 1D001 The Zone No Output feature allows the programmer to view the zones which have not been programmed to at least one output device (not including general alarm Zone 00).

  • Page 104: 5: System

    Programming Maintenance Programming Level 3.7.5 System Pressing 2 while viewing Maintenance Screen #2, will display the following screen: PROGRAMMING 1=WALKTEST SYSTEM SYSTEM 2=SYSTEM 1=TIME/DATE 3=ZONE SETUP 1=NACS ENAB 1,2,3,4 2=REM SYNC ENAB YES 2=CHARGER ENAB Maintenance Screen #2 3=4XTM SPV ENB System Screen #1 System Screen #2 Pressing 1 while viewing System Screen #1 will display the following:...
  • Page 105 Maintenance Programming Level Programming Pressing 1 while viewing Zone Setup screen will display the following screen: ZONE TO ENABLE Z Enable Screen A flashing cursor appears to the right of the Z. To enable a zone, enter the three digit zone number (000 - 099). After the second digit is entered, the zone will be enabled and the cursor will return to the original position.

  • Page 106: Section 4: Operating Instructions

    Section 4: Operating Instructions 4.1 Panel Control Buttons 4.1.1 Acknowledge The first press of the Acknowledge key silences the piezo sounder, changes flashing LEDs to steady, and also changes the status field on the LCD display from capital letters to small letters. When the piezo is silenced, an acknowledge message is sent to the printer and the history file.

  • Page 107: Normal Operation

    Normal Operation Operating Instructions Disabled This is a yellow LED that flashes to indicate that a zone, NAC, detector or module has been temporarily disabled in programming by the user. Maintenance This is a yellow LED that flashes to indicate that a smoke detector requires cleaning or replacement due to an invalid chamber reading or excessive drift.

  • Page 108: Alarm Operation

    Operating Instructions Alarm Operation  <NOUN>; refers to the user programmed noun descriptor from library list resident in the control panel or custom entry via PC. • Third line in display: INVREP indicates an invalid reply from the addressable device. Other possible troubles include: –...

  • Page 109: Co Alarm Operation

    CO Alarm Operation Operating Instructions • Third line in display: Z000 indicates the zone programmed to this device which, in this example, is general alarm Zone 000. Note that a single device can be programmed to five different zones but only the first zone will be displayed. •...

  • Page 110: Process Monitor Operation

    Operating Instructions Process Monitor Operation A typical Supervisory event would be displayed as illustrated in the following: ACTIVE SUPERVISORY <ADJ> <NOUN> Z000 10:00A 012116 1M001 Note that, like alarms, supervisory signals latch (except when programmed for supervisory autoresettable) and can be assigned to soft- ware zones.

  • Page 111: Mass Notification Operation

    Mass Notification Operation Operating Instructions • Timers are not started • Store event in history buffer • Activate appropriate LED on the N-ANN-LED annunciator (required for this application) • Each N-ANN-LED can support up to 10 zones. Medical alert conditions latch. They can be assigned to software zones. 4.11 Mass Notification Operation The FACP may be installed with an NFC-50/100 audio system to provide mass notification operation.

  • Page 112: Time Functions: Real-Time Clock

    Operating Instructions Time Functions: Real-Time Clock Smoke Detector Data Smoke detector data is monitored by the FACP, eliminating the need to test the sensitivity of each detector at its location. A printout of ® each detector’s data can be retrieved from the FACP using an optional printer or Windows HyperTerminal.

  • Page 113: Special System Timers

    Special System Timers Operating Instructions  control panel LCD display will indicate a presignal event and the active point  control points programmed to Zone 097 will activate  outputs (NACs and control modules) of associated zones will be inhibited from activating for a factory set duration of 15 seconds ...

  • Page 114: 6: Control Module Delay Timer

    Operating Instructions Walktest 4.22.6 Control Module Delay Timer The control module delay feature, if enabled, will delay activation of a control module after a programmed time of 1-180 seconds after being triggered by an alarm condition. This feature requires the approval of the local Authority Having Jurisdiction. See the table on page 49 for allowable settings.

  • Page 115: 2=Zones

    Read Status Operating Instructions The operator selects the type of device which is to be viewed by pressing 1 for Detector or 2 for Module. If 1 is pressed, the display will change to the following screen: READ SYSTEM POINT ENTER DETECTOR# ...

  • Page 116: 3: Trouble Reminder

    Operating Instructions Read Status 4.24.3 Trouble Reminder Pressing 1 while viewing Read Status Screen #2 will display the following screen: READ STATUS 1=TROUBLE REMINDER TROUBLE REMINDER 2=TIMERS TROUBLE REM 24HR 3=NAC Read Status Screen #2 The screen indicates whether the Trouble Reminder feature is set to sound every 4 or 24 hours. 4.24.4 Timers Pressing 2 while viewing Read Status Screen #2 will cause the following Timer screens to be displayed: TIMERS...

  • Page 117: 8: History

    Read Status Operating Instructions Pressing 2 while viewing the Program Check screen #1 will display a screen which will indicate if any output zones have not been pro- grammed to at least one input zone. Use the up and down arrow keys to view all zones. Pressing 3 while viewing the Program Check screen #1 will display a screen which will indicate if any input zones have not been pro- grammed to at least one output zone.

  • Page 118: 11: Print

    Operating Instructions Read Status Pressing 2 for POTS Settings while viewing Communicator Screen #1 will display settings for the telephone portion of the Communica- tor. POTS SETTINGS 1=LINE 1 2=LINE 2 3=GAINS Pressing 1 or 2 will display whether each phone line is enabled Yes or disabled No, whether the phone type is touchtone or rotary, and whether the phone line is being supervised Yes or No.

  • Page 119: Chamber Value

    Read Status Operating Instructions Pressing 1 while viewing Print Screen #2 allows the user to print the detector data for each addressable smoke detector connected to the system. A printout, similar to the following example, will be generated if an optional printer is connected to the FACP. DEVICE # DEVICE TYPE % DRIFT COMP...

  • Page 120: 12: Time-Date

    Operating Instructions Read Status Figure 4.1 illustrates a graphic representation of the maintenance levels: DIRTY Maintenance Urgent Maintenance Alert Acceptable Range Low Chamber Reading VALUE Figure 4.1 Diagram of Maintenance Levels Pressing 2 while viewing Print Screen #2 allows the user to print the Communicator’s settings. Refer to PRINT “Communicator”...

  • Page 121: Section 5: Central Station Communications - Pots Transmission

    Section 5: Central Station Communications - POTS Transmission The control panel transmits zone and system status reports to Central Stations via the public switched telephone network. Two super- vised telephone line connections are made to interface the control panel to the telephone lines. Two optional 7 foot telephone cords are available for this purpose and can be purchased separately.
  • Page 122 Central Station Communications - POTS Transmission Transmittal Priorities Red LEDs are provided on the circuit board to identify which telephone line is activated. Also, a green LED labeled Kissoff will turn on whenever the control panel has successfully transmitted reports to the Central Station. The Kissoff LED may turn on several times during communications with a Central Station.

  • Page 123: Section 6: Fs-Tools Upload/Download

    Section 6: FS-Tools Upload/Download Important! The FACP will automatically reset 2 minutes after completion of a user program download via the FS-Tools programming utility. To prevent program corruption, the operator must wait until this panel reset occurs before performing any panel operations. The control panel may be programmed or interrogated off-site via an Ethernet connection or locally using a USB cable.

  • Page 124: 1: Security Features

    FS-Tools Upload/Download Transferring a Program  The control panel must be in the Normal Mode of operation. Downloading is not possible if the panel is in any other mode  There cannot be any active communications ongoing with a Central Station receiver ...

  • Page 125: Section 7: Usb Upload/Download

    Section 7: USB Upload/Download Important! The FACP will automatically reset 2 minutes after completion of a user program download. To prevent program corruption, the operator must wait until this panel reset occurs before performing any panel operations. CAUTION: After successfully downloading a program, make certain to perform the following steps: Print out all programmed data via Print Mode or manually view programmed entries and compare to intended program data Test all affected panel operations Immediately correct any problems found...
  • Page 126 USB Upload/Download USB Upload/Download Pressing 2 for Yes will cause the following screen to be displayed: USB UP/DOWNLOAD SYSTEM CONFIGURATION TRANSFER IN PROCESS PLEASE WAIT An error message will display if there is no USB drive inserted in the FACP or if there is no existing configuration saved on the USB drive.

  • Page 127: Section 8: Firmware Upgrade

    Section 8: Firmware Upgrade In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent upgrades to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly recommend that you download the most current version of software for each product from www.notifier.com prior to commissioning any system.

  • Page 128: Section 9: Power Supply Calculations

    Section 9: Power Supply Calculations 9.1 Overview This section contains instructions and tables for calculating power supply currents in alarm and standby conditions. This is a four-step process, consisting of the following: Calculating the total amount of AC branch circuit current required to operate the system Calculating the worst-case system current load on the control panel, when primary (AC) power is applied, to assure that the limit of the its internal power supply will not be exceeded.
  • Page 129 Calculating the System Current Load Power Supply Calculations Calculation Column 1 Calculation Column 2 Calculation Column 3 Device Type Primary (AC) Power Source Secondary (Battery) Power Source Secondary (Battery) Power Source Fire Alarm Current (amps) Fire Alarm Current (amps) Standby Current (amps) X[current draw]= Total X [current draw]=...

  • Page 130: Calculating The Battery Size

    Power Supply Calculations Calculating the Battery Size When AC power is initially applied to the panel and the battery is not fully charged, an initial charge current of up to 5.3 amps may be observed at the battery. This high current is only applied for a very short duration (milliseconds) and does not affect system load or battery size calculations. 10 Total Standby current load cannot exceed 2.25 amps.

  • Page 131: Appendix A: Software Zones

    Appendix A: Software Zones A.1 Correlations Setup and configuration of an addressable system is different than a conventional system. In a conventional system, assignment of input devices (smoke detectors, pull stations, heat detectors, etc.) to zones is accomplished through wiring. The wiring is direct from clearly marked panel terminals to any device assigned to a particular zone.
  • Page 132 Software Zones Correlations Correlation of Input and Output Zones Input Devices Zones Output Devices smoke control smoke control ZONE monitor control monitor control control monitor control smoke ZONE control smoke smoke control smoke ZONE smoke control monitor NFW-100X Manual — P/N LS10131-001NF-E:C 7/25/2018...
  • Page 133 Correlations Software Zones The zone correlations which are shown graphically above are also presented in Table A.1 on page 133 and Table A.2 on page 134. DETECTOR ZONE ASSIGNMENT Address Device Type Zone Number ADJ/NOUN Address Device Type Zone Number ADJ/NOUN smoke FIRST HALL...
  • Page 134 Software Zones Correlations MONITOR/CONTROL MODULE ZONE ASSIGNMENT Address Device Type Zone Number ADJ/NOUN Address Device Type Zone Number ADJ/NOUN monitor monitor 1, 2 monitor 1, 2 monitor control control control control control 1, 2, 3 control Table A.2 Module Programming Sheet Example NFW-100X Manual —...
  • Page 135 Correlations Software Zones DETECTOR ZONE ASSIGNMENT Address Device Type Zone Number ADJ/NOUN Address Device Type Zone Number ADJ/NOUN Table A.3 Blank Detector Programming Sheet NFW-100X Manual — P/N LS10131-001NF-E:C 7/25/2018...
  • Page 136 Software Zones Correlations MONITOR/CONTROL MODULE ZONE ASSIGNMENT Address Device Type Zone Number ADJ/NOUN Address Device Type Zone Number ADJ/NOUN Table A.4 Blank Module Programming Sheet NFW-100X Manual — P/N LS10131-001NF-E:C 7/25/2018...

  • Page 137: Appendix B: Default Programming

    Appendix B: Default Programming The following table provides a list of the programming options and their factory default settings. Program Option Factory Default Program Option Factory Default Detector Programming Not Installed Aux Power Class A Detector Type Smoke-Photo Aux Power Resettable Detector Verification Aux Power 2 Resettable Detector Walktest...

  • Page 138: Appendix C: Nfpa Standard-Specific Requirements

    Appendix C: NFPA Standard-Specific Requirements The NFW-100X has been designed for use in commercial, industrial, and institutional applications and meets the requirements for ser- vice under the National Fire Protection Association (NFPA) Standards outlined in this Appendix. The minimum system components required for compliance with the appropriate NFPA standard are listed below: NFW-100X Control Panel...
  • Page 139 NFPA Standard-Specific Requirements NFPA 72 Remote Station Protective Signaling System Notes: Cut Jumper JP3 on the NFW-100X main circuit board to supervise placement of the 4XTM module. Refer to “4XTM Transmitter Module Installation” on page 31 for detailed information. RS82 Remote Station Receiver UL listed. Refer to Instruction Manual for Remote Station Receiver Model RS82.
  • Page 140 NFPA Standard-Specific Requirements NFPA 72 Proprietary Protective Signaling Systems NFW-100X Addressable Fire Control Panel NFW-100X Main Board Form-C Alarm contact programmed to activate on General Alarm. Form-C Trouble contact which will automatically activate on any Trouble condition. Form-C relay contact programmed to activate on Supervisory condition.

  • Page 141: C.1: Mbt-1 Municipal Box Trip - Silenceable

    MBT-1 Municipal Box Trip - Silenceable NFPA Standard-Specific Requirements C.1 MBT-1 Municipal Box Trip - Silenceable The following figure illustrates the connection of the MBT-1 (Municipal Box Trip) between the FACP and a Local Energy Municipal Box. The use of an addressable control module programmed for General Alarm and Silenceable allows silencing of the Municipal Box without resetting the panel or box.

  • Page 142: Appendix D: Wire Requirements

    Appendix D: Wire Requirements T-tapping of the SLC loop wiring is allowed for 2-wire (Class B) configurations. The total resistance of any branch cannot exceed 40 ohms. The total wire length of all branches cannot exceed 10,000 feet (3,000 m). Connecting external system accessories to the NFW-100X main circuits must be carefully considered to ensure proper operation.

  • Page 143: D.1: Nac Wiring

    NAC Wiring Wire Requirements D.1 NAC Wiring The following table lists NAC wiring requirements for the FACP. CLASS-B CLASS-A Max. Max. allowable wire pair length Max. allowable wire pair length allowable NAC Load (feet) (feet) total loop (Amps) resistance AWG 12 AWG 14 AWG 16 AWG 18...

  • Page 144: Appendix E: Hvac Control

    Appendix E: HVAC Control The FACP can be programmed to shut down a building’s HVAC fans in the event of a fire. The fans cannot be restarted until the fire alarm condition has been cleared and the FACP has been reset to a normal (non-alarm) condition. IMPORTANT! This HVAC feature is not to be used for smoke control.

  • Page 145: E.2: Monitor Module Operation

    Monitor Module Operation HVAC Control E.2 Monitor Module Operation E.2.1 HVAC RESTART The HVAC RESTART type code can be assigned to any addressable monitor module for the purpose of resetting (deactivating) the HVAC SHUTDN control module and turning the fans back on. The HVAC RESTART monitor module acts globally throughout the FACP system and therefore is not programmed to a particular software zone.

  • Page 146: Appendix F: Ademco Contact Id Format Event Code Descriptions

    Appendix F: Ademco Contact ID Format Event Code Descriptions This appendix describes the various Event Codes and their messages which are available for the Ademco Contact ID Format. F.1 Transmission Format Between DACT and Receiver The transmission string for the Ademco Contact ID Format is as follows: SSSS 18 QXYZ GG CCC where SSSS...
  • Page 147 Ademco Contact ID Typical Printout Ademco Contact ID Format Event Code Descriptions EVENT CODE CLASSIFICATIONS ALARMS SUPERVISORY TROUBLES OPEN/CLOSE DISABLES/BY TEST/MISC. REMOTE ACCESS PASSES Medical Fire System Open/Close System Test Fire Sounder/Relay Remote Access Sounder/Relay Panic System Peripheral Access Control System Peripheral Burglary Communication...
  • Page 148 Ademco Contact ID Format Event Code Descriptions Ademco Contact ID Typical Printout EVENT MESSAGE 24-Hour Non-Burglary - 150 and 160 150 24-Hour Non-Burg ALARM - 24-Hr. Non-Burg - # 151 Gas detected ALARM - Gas Detected - # 152 Refrigeration ALARM - Refrigeration - # 153 Loss of heat ALARM - Heating System - #...
  • Page 149 Ademco Contact ID Typical Printout Ademco Contact ID Format Event Code Descriptions EVENT MESSAGE Communication Troubles - 350 and 360 350 Communication TROUBLE - Communication Trouble 351 Telco 1 fault TROUBLE - Phone Line #1 352 Telco 2 fault TROUBLE - Phone Line #2 353 Long range radio transmitter fault TROUBLE - Radio Transmitter 354 Fail to communicate...
  • Page 150 Ademco Contact ID Format Event Code Descriptions Ademco Contact ID Typical Printout EVENT MESSAGE 527 Bell 4 disable DISABLE - Bell/Siren - #4 System Peripheral Disables - 530 and 540 Communication Disables - 550 and 560 551 Dialer disabled DISABLE - Dialer Disable 552 Radio transmitter disabled DISABLE - Radio Disable Bypasses - 570...

  • Page 151: Appendix G: Central Station Points

    Appendix G: Central Station Points The control panel transmits Central Station Reports in a numerical format which indicates the FACP addressable device address that is reporting. The following table indicates the Central Station Report (CS Report) number that will be transmitted and the addressable device address it represents.
  • Page 152 Central Station Points Module Module Module Module Report Address Report Address Report Address Report Address Table G.2 Addressable MODULES NFW-100X Manual — P/N LS10131-001NF-E:C 7/25/2018...

  • Page 153: Appendix H: Nfpa Requirements

    Appendix H: NFPA Requirements The following is the minimum configuration to meet the NFPA requirements. Process Module Local Proprietary Management NFW-100X IPOTS-COM (pre-installed communicator) 4XTM DP-ES-R or DP-ES-B NFS-LBB N-ANN-LED N-ANN-80 N-ANN-100 N-ANN-S/PG N-ANN-I/O N-ANN-RLED N-ANN-RLY Where Y = Yes, N = No, and O = Optional Non-Emergency One of the indicated modules is required when the IPOTS-COM is not employed.

  • Page 154: Appendix I: Open/Short/Ground Trip Values

    Appendix I: Open/Short/Ground Trip Values Table I.1 lists the earth fault resistance detection for each applicable terminal on the FACP. Output Circuit Terminal Trip Resistance (in ohms) Remote Sync 360K Remote Sync 330K NAC 1-2 360K NAC 1-2 320K ANN Bus 270K ANN Bus 265K...

  • Page 155: Index

    Index Numerics auxiliary power 14 control buttons 106 control module 17 24 hour test time 85 description display 67 24VDC power 71 display 65 4XTM module 138 backbox 17 edit 65 coil resistance 32 see also cabinet 24 enable/disable 65 current 32 banner 71 MNS override 68...
  • Page 156 Index DIRTY2 119 disable gains 82 maintenance alert 13 battery charger 71 gateway IP address 83 levels 119 charger 71 general alarm zone maintenance program level 2 51 zone 68 see also zone Z000 57 manual programming 50 disable point ground fault 46 master program level 1 51 maintenance level 101...
  • Page 157 Index N-ANN-RLED annunciator module 14 change 99 modules 60 N-ANN-RLY relay module 14 invalid 99 off-line computer 50 N-ANN-S/PG printer module 14 maintenance level 2 101 via computer keyboard 49 NFC-50/100 19 phone line supervision 82 via panel keypad 49 NFC-FFT 19 phone number 84 programming levels 51...
  • Page 158 Index sensitivity 112 system point 114 waterflow silenceable 71 see also smoke detector sensitivity 112 system setup 71 wire requirements 142 signal rate 13 wireless detector 57 signaling line circuit wireless gateway 19 see also SLC 14 wiring 47 telephone circuitry 20 silence inhibit 13 wiring telephone company...
  • Page 159 Slide-in Labels Carefully cut along the outside of each label. Identify Function (F1-F4) keys as desired and slide the labels into the keypad. Starting at the center of the keypad next to the Function Keys, slide each label into the groove towards the outer edge. Function Keys F1 and F3 are not programmable in Canadian applications.
  • Page 160 NFW-100X Manual — P/N LS10131-001NF-E:C 7/25/2018...
  • Page 161 NFW-100X Series Fire Alarm Control Panel Operating Instructions NORMAL - Only AC POWER is illuminated green. PANEL KEY - The key to open the panel can be found at the following All other indicators are off. LCD display will read SYSTEM ALL location: NORMAL.
  • Page 163 Manufacturer Warranties and Limitation of Liability Manufacturer Warranties. Subject to the limitations set forth herein, Manufacturer warrants that the Products manufactured by it in its Northford, Connecticut facility and sold by it to its authorized Distributors shall be free, under normal use and service, from defects in material and workmanship for a period of thirty six months (36) months from the date of manufacture (effective Jan.
  • Page 164 NOTIFIER 12 Clintonville Road Northford, CT 06472-1610 USA 203-484-7161 www.notifier.com...

Table of Contents