King gates STARG8 24NG Installation And Use Instructions Manual page 38

16.2 - Activating/deactivating start
and pedestrian security mode
Default = wired start input and start button of the control
unit are activated.
This programming sequence allows for better security by
disabling the operation of the START / PED wired input and the
start button on the control unit. The control unit is now activated
with the transmitter only.
1. PRESS THE START BUTTON FOR 3 SECONDS: all leds turn
OFF (if not, consult Paragraph 17.1)
2. PRESS THE SET BUTTON FOR 1 SECOND
- If the ERROR led is ON
security = activated (if the setting is correct, go to Point 5; if
not, proceed to Point 3)
- If the ERROR led is OFF
security = deactivated (if the setting is correct, go to Point
5; if not, proceed to Point 4)
3. PRESS THE START BUTTON FOR 1 SECOND: the SET led
remains lit and the ERROR led turns OFF. Go to step 5
4. PRESS THE START BUTTON FOR 1 SECOND: the SET led
remains lit and the ERROR led turns ON
5. PRESS THE SET AND RADIO BUTTONS
SIMULTANEOUSLY OR WAIT 10 SECONDS TO EXIT THE
PROCEDURE: the leds return to the normal operation
configuration
m
If the security command lock is activated, any device
connected to the START and PED contacts will not be
detected by the control unit. When these contacts are
closed, the START led will emit brief flashes.
17. Other functions
m
To interrupt the following programming sequences at
any time, press the SET and RADIO buttons simultaneously
or wait 10 seconds.
17.1 - Activating/deactivating the
control unit protection device
Default = control unit protection device not active.
m
This programming sequence allows for locking all
control unit programming sequences and the settings
adjustable through the dip-switches. To perform a new
programming sequence or make a dip-switch/trimmer
modification effective, the protection must be deactivated.
36
Advanced programming (not required for standard installations)
1. PRESS THE START BUTTON FOR 3 SECONDS:
2. PRESS BOTH BUTTONS START AND RADIO, FOR 2
3. PRESS BOTH BUTTONS START AND RADIO, FOR 2
4. PRESS THE SET AND RADIO BUTTONS
17.2 - Energy saving mode
This feature cuts the power supply to the photocells when the
control unit is on standby, therefore it decreases the power
consumption. It is useful in case of battery power supply
conditions.
m
gate pilot light function is deactivated (Paragraph 9.7)
m
accessories powered with 24VDC.
1. PRESS THE START BUTTON FOR 4 SECONDS: all leds turn
2. SIMULTANEOUSLY PRESS THE SET AND START
3. PRESS THE SET BUTTON FOR 1 SECOND: the led SET and
4. PRESS THE SET BUTTON FOR 1 SECOND: the led SET and
5. PRESS THE SET AND RADIO BUTTONS
m
mode activated
Once the function is activated, it is necessary to connect the
24VDC positive pole of the safety accessories (for example:
photocells) to terminal GSI. The control devices (e.g.: receivers,
spires or photocells connected to the Start contact) must be
connected to terminal +VA.
m
unit open the accessories remain powered to retain the re-
closing function.
m
will turn OFF after 2 minutes of stand-by.
- if the leds SET, RADIO and START are ON
control unit lock = enabled (if it is the correct setting, go to
step 4, otherwise proceed to step 2)
- If the leds SET, RADIO and START are OFF
control unit lock = disabled (if it is the correct setting, go to
step 4, otherwise proceed to step 3)
SECONDS: the leds SET, RADIO and START go OFF.
Go to step 4
SECONDS: the leds SET, RADIO and START go ON
SIMULTANEOUSLY OR WAIT 10 SECONDS TO EXIT THE
PROCEDURE: the leds return to the normal operation
configuration
When the energy saving mode is activated, the open
The energy saving mode can only be used with safety
OFF (if not, consult Paragraph 17.1)
BUTTONS FOR 2 SECONDS:
- If the led PHOTO is ON
Energy saving = enabled (if it is the correct setting, go to
step 5 otherwise proceed to step 4)
- If the red led PHOTO is OFF
Energy saving = disabled (if it is the correct setting, go to
step 5 otherwise proceed to step 4)
the START are ON, while the led PHOTO turns OFF.
Go to step 5
the START are ON, while the led PHOTO turns ON
SIMULTANEOUSLY OR WAIT 10 SECONDS TO EXIT THE
PROCEDURE: the leds return to the normal operation
configuration
Connection of accessories with the energy saving
If DIP-SWITCH 7 FAST is put to ON, with the control
If you activate the power saving mode all the LEDs