Table of Contents
Advertisement
Star 224
Star M 224
SWING GATE CONTROL UNIT VER. AUS 4 – MANUAL
Star 224=
Control unit for 1 or 2 24 Vdc Jet motors / Modus motors
KINGgates srl
Via A. Malignani, 42 - 33077 Sacile (PN) ITALY
Tel. +39 0434 737082 - Fax +39 0434 783382
web:www.king-gates.com Email:info@king-gates.com
Allegro Gate Automation Pty. Ltd.
U2/ 49 Biscayne Way, Jandakot W.A. 6164
08-94173190
Allegroau@hotmail.com
www.allegrogateautomation.com.au
Advertisement
Table of Contents
Related Manuals for King gates Star 224
Summary of Contents for King gates Star 224
- Page 1 Star 224 Star M 224 SWING GATE CONTROL UNIT VER. AUS 4 – MANUAL Star 224= Control unit for 1 or 2 24 Vdc Jet motors / Modus motors KINGgates srl Via A. Malignani, 42 - 33077 Sacile (PN) ITALY Tel.
-
Page 2: Table Of Contents
Main Menu Section Page 1 - Safety notice 2 - Electrical connection 3 - DIPSWITCHES Setting 4 - Linear adjustment Potentiometers 5 - Remote Control Programming - Main, Vehicle access 6 - Remote Control Programming - Pedestrian access 7 - Remote Control - Deleting all remote codes from control unit memory 8 - POWER, SPEED, OBSTACLE Adjustments 9 - Automatic Gate Travel learning ADVANCED PROGRAMMING... -
Page 3: Electrical Connection
2 - ELECTRICAL CONNECTIONS Cable length and cross section - If the distance between the control unit and the grounding system is more than 30m, then it is necessary to install an electric discharger near the control unit - Cables used for low-voltage features must be at least 0.25 mm2 for distance up to 30meters - Use shielded (screened) cables that are at least 0.5mm2 for distance 30 -100meter - Do not connect cables in underground boxes or inside conduits PHOTOCELL CONNECTION - VIKY SERIES... -
Page 4: Dipswitches Setting
3 - SETTING THE DIPSWITCHES - DipSwitches settings will only take effect after the system has reached the end of a cycle. i.e. when the gate closed or when the system has been reset (power off, battery and mains) DIP sw.1 needs to be set BEFORE the gate travel learning DS-1: Motor Motor type (to set before gate travel learning) Folding arm Modus,Minimodus... -
Page 5: Remote Control Programming - Main, Vehicle Access
5 - PROGRAMMING THE REMOTE CONTROL FOR MAIN VEHICLE ACCESS - FULL OPENING 1) Make sure that: A) Power – B) DipSwitch 8 - ON 2) Press the RADIO button in the control box for 3 seconds the RADIO-LED turns on 3) Choose the remote’s button you want to use for vehicle access opening (usually the large one) and press it The RADIO-LED flashes shortly... -
Page 6: Automatic Gate Travel Learning
9 - AUTOMATIC GATE TRAVEL LEARNING Before the Automatic Learning! - In this process the controller “learns” the gate’s travel time and automatically sets the default slowdown points - During the Automatic Learning safety devices are disabled! Keep the gate travel area clear to prevent any damage that may be caused by crushing into an object, vehicle, person, animals... -
Page 7: Pedestrian Access Deleting All Remote Control Codes
12 - RESET THE PEDESTRIAN OPENING GAP TO DEFAULT SETTING 1) Make sure that the gate is in the closed position 2) Press the SET button for 2 seconds >> SET LED begins to flash 3) Press the START button >>... -
Page 8: Accessories, Optional
15 - OPTIONAL ACCESSORIES HAZ – HAZARD LIGHT output: terminals 10, 19; 12 VDC Max 15W. (0.6Amp); for connection of hazard light. Turns on a second before the wings move. DipSwitch-5 setting: ON: Flashing / / OFF: steady on ANTENNA input : terminals 1,2 - for increasing reception range connect an external antenna (Item code: ANT 433) and remove internal antenna (the wire from the terminal) TX –... -
Page 9: Inside The Control Unit (Advanced Only)
17 - INSIDE THE CONTROL UNIT (advanced only) NOTES: opening the board case may cancel the warranty for the board 12V 2Amp fuse Remotes Receiver Remotes Memory card... -
Page 10: Trouble Shooting
18 - TROUBLE SHOOTING THE RED ERROR (ERR) LED TURNS ON, AND THE CONTROL UNIT DOES NOT FUNCTION - Repeat Automatic Gate Travel Learning – see section 9 -The control unit is in Safety Test mode (section 14) to deactivate: - Faulty control unit –... - Page 12 King Gates S.r.l. Via A. Malignani, 42 - 33077 Sacile (PN) ITALY Tel. +39 0434 737082 - Fax +39 0434 783382 e-mail: info@king-gates.com web: www.king-gates.com...