Table of Contents
Advertisement
NOTES TO USERS
(1) Description in this manual is subject to change without any obligation on the part of the Manu-
facturer.
(2) Notice would be appreciated if you find any question, omission or error in this manual.
(3) Disassembly, maintenance or repair, other than in accordance with the instruction herein or other
specific written instruction from MOOG will invalidate MOOG's obligations under its warranty.
Refer to MOOG warranty for complete previsions thereof.
SAFETY INSTRUCTION
Description in this manual is essential to the safety of life and property, therefore, before operating
this equipment, you should first thoroughly read this manual, and this manual should be kept in ac-
cessible for when you have any questions.
WARNING
This symbol with the word "WARNING" is used to call attention to safety instructions
concerning a potential hazard to people. Failure to comply with these safety instructions
can result in serious damage to health and can even prove fatal in extreme cases.
CAUTION
This symbol with the word "CAUTION" is used to call attention to instructions concern-
ing potential damage to the equipment or to the system as a whole.
NOTE
Notes contain useful information to the operator when starting up and operating the equip-
ment or system.
MOOG INTELLECTUAL AND PROPRIETARY INFORMATION LEGEND
This technical Document contains information that is proprietary to, and is the express property of Moog Inc., or Moog Inc. subsidiaries
except as expressly granted by contract or by operation of law and is restricted to use by only Moog employees and other persons
authorized in writing by Moog or as expressly granted by contract or by operation of law. No portion of this Data/Drawing/Document
shall be reproduced or disclosed or copied or furnished in whole or in part to others or used by others for any purpose whatsoever
except as specifically authorized in writing by Moog Inc.
© MOOG 2010
This document is subject to MOOG INTELLECTUAL AND PROPRIETARY INFORMATION LEGEND . The details are on page II.
MOOG JAPAN LTD.
1-8-37 NishiShindo, Hiratsuka, Japan 254-0019
Tel:+81-463-55-7141 Fax:+81-463-54-4709
III
MRJ04410
Advertisement
Table of Contents
Need help?
Do you have a question about the DigiPack Ⅱ and is the answer not in the manual?
Questions and answers
How..to set up the..Digi pack 2 on machine
To set up the Moog DigiPack II on a machine, follow these key steps:
1. Installer Requirements: The installer must be familiar with electrical wiring, hydraulic plumbing, basic metal work, and have some understanding of the blow molding process. Use of test instruments like a digital voltmeter is also required.
2. Mechanical Installation:
- Install and adjust tooling and die gap actuators.
- Mount the servovalve and manifold.
- Install the hydraulic cylinder and ensure it meets customer specifications.
- Measure and set accumulator position.
- Ensure proper filtration and install filters.
- Connect the hydraulic power supply and follow startup instructions.
- Implement contamination control.
3. Electrical Installation: Follow the manual's guidance for electrical connections.
4. Software Update (if needed):
- Power off DigiPack II and remove the SD card.
- Save the “DIGIPK2.FWM” file to the SD card using a PC.
- Reinsert the SD card and power on the unit.
- Press “X10” and “Cursor Down” keys simultaneously during startup.
- Wait for the “Updating firmware……” message.
- Confirm update by checking the software version on the startup display.
5. Calibration and Setup:
- Set accumulator working stroke, shot size, and end position.
- Interface DigiPack II with the machine’s PLC for motion control.
Proper installation following the manual ensures reliable long-term operation.
This answer is automatically generated
The shot size is to short and the Digi pack to is not in command..
If the shot size is too short and the Moog DigiPack II is not functioning properly, turn the Entry Knob clockwise to increase the Shot Size value on the LCD display. Then press the Set button to make the change permanent.
This answer is automatically generated