Table of Contents
Advertisement
Image porcessing
PRNU
DSNU
Power supply voltage
Connectors / LEDs
Lens mount
Flange back
Operating temperature / humidity
Storage temperature / humidity
Vibration resistance
Impact resistance
Standard compliance
Dimensions
Weight
Package contentsCamera
body (1)
Sensor protection cap (1)
Dear Customer (sheet) (1)
Design and specifications are subject to change without notice.
Approximately 30 minutes of warm-up are required to achieve these specifications.
Caution
About the verified performance temperature
Make sure the following temperature conditions are met when operating the unit.
1) The camera's internal temperature sensor detects temperatures of 98 °C or less during
operation.
If the above temperature conditions are exceeded, take measures to dissipate heat according to
your installation environment and conditions.
1 Pixel sensitivity correction: Pixel correction (DSNU, PRNU)
2 Shading correction: ColorShading, FlatShading
3 LUT: OFF: γ＝1.0, ON: 257 points can be set
4 Gamma: 0.45, 0.5, 0.55, 0.6, 0.65, 0.75, 0.8, 0.9, 1.0 (9 steps available)
Post-correction: Within ±1% (during 100% output)
Post-correction: Within ±5% (during 0% output)
12pin
PoE+
IEEE802.3at compatible
Support for Layer 1 classification only
RJ-45
12pin (DC IN/TRIG)
10pin (AUX)
LED (Power/TRIG)
M52 mount, F mount
M52 mount: 46.5 mm (in air), tolerance: 0 mm to –0.05 mm
F mount:
46.5 mm,
tolerance: 0 mm to –0.05 mm
5℃〜＋ 45℃ / 20％〜 80％
（non-condensing）
25℃〜＋ 60℃ / 20％〜 80％
（non-condensing）
3G（20 Hz 〜 200 Hz X-Y-Z direction）
50G
CE（EN61000-6-2 and EN61000-6-3）、FCC part 15 class B、 RoHS、WEEE
90 × 90 × 90 mm (WHD; excluding mount and protrusions)
830 g (Typ.)
— 59 —
Input range： DC ＋10V 〜＋ 25V
consumption：
13.7 W(typ.)
(at 12 V input, full pixel, Default setting, Environmental
temperature 25°C) (Typical)
19.3 W
(Maximum)
Input range： ＋42V 〜＋ 57V
consumption：
15.3 W(typ.)
(at full pixel, Default setting, Environmental
temperature 25°C) (Typical)
21.7 W
(Maximum)
Ethernet standards and the cable type and the maximum cable
length.
1000 Base-T : Cat5e, Cat6, Cat6e, Cat6A, Cat7
2.5G Base-T : Cat5e, Cat6, Cat6e, Cat6A, Cat7
5G Base-T : Cat6, Cat6e, Cat6A, Cat7
10G Base-T : Cat6*, Cat6e*, Cat6A, Cat7
*) The maximum cable length is limited to 55m.
Model
： HR10A-10R-12PB(71) (or equivalent)
Function： Power supply input / External trigger / External I/O
Model
Camera side：Equivalaent to Hirose Electronic 3260-10S3 (55)
Cable side ：Equivalaent to Hirose Electronic 350-10P-C (50)
Function： External tigger / External I/O
Function：Power on, trigger input indicator
SW-4000T-10GE
Advertisement
Table of Contents
