QuadTech Sentry Plus Series Instruction Manual page 18

Condensed Operating Instructions (Continued)
Step Test Parameter
1 To enter
programming mode
2 Select Test Step
3 Select Test Mode
4 Set Test Voltage
Set Current (GC)
5 Set High Limit *
Set Low Limit (IR)
6 Set Test Time
Set Dwell (GC) ***
7 Set Low Limit **
Set High Limit (IR)
8 Set ARC Limit
9 Set Ramp Time
10 Set Dwell Time***
11 Set Fall Time
12 Set In-Rush Current
13a To program next test
step OR
13b To exit
programming mode
* High limit decision is made throughout test time.
** Unit will make low limit decision at the end of test.
* ** Limits will be checked at end of dwell time.
Page 18 of 85
Table COI-1: Test Parameter Setup
AC Hipot DC Hipot
[F1] = [F1] =
PROGRAM PROGRAM
[F1] = UP [F1] = UP
[F3] = NEXT [F3] = NEXT
[F1] = UP [F1] = UP
[F3] = NEXT [F3] = NEXT
[F1] = INC. [F1] = INC.
[F3] = NEXT [F3] = NEXT
[F1] = INC. [F1] = INC.
[F3] = NEXT [F3] = NEXT
[F1] = INC. [F1] = INC.
[F3] = NEXT [F3] = NEXT
[F1] = INC. [F1] = INC.
[F3] = NEXT [F3] = NEXT
[F1] = INC. [F1] = INC.
[F3] = NEXT [F3] = NEXT
[F1] = INC. [F1] = INC.
[F3] = NEXT [F3] = NEXT
[F1] = INC.
[F3] = NEXT
[F1] = INC. [F1] = INC.
[F3] = NEXT [F3] = NEXT
[F1] = INC.
[F3] = NEXT
[F1] = NEW [F1] = NEW
OR OR
[F4] = EXIT [F4] = EXIT
IR GC
[F1] = [F1] = PROGRAM
PROGRAM
[F1] = UP [F1] = UP
[F3] = NEXT [F3] = NEXT
[F1] = UP [F1] = UP
[F3] = NEXT [F3] = NEXT
[F1] = INC. [F1] = INC.
[F3] = NEXT [F3] = NEXT
[F1] = INC. [F1] = INC.
[F3] = NEXT [F3] = NEXT
[F1] = INC. [F1] = INC.
[F3] = NEXT [F3] = NEXT
[F1] = INC. [F1] = INC.
[F3] = NEXT [F3] = NEXT
[F1] = INC.
[F3] = NEXT
[F1] = INC.
[F3] = NEXT
[F1] = INC.
[F3] = NEXT
[F1] = NEW [F1] = NEW
OR OR
[F4] = EXIT
Range
1-10
AC, DC, IR, GC, PA
0.05-5kV AC
0.05-6kV DC
0.05-1kV IR
0.1A GC
0.001-20mA AC
0.0001-5mA DC
0.1-50000MΩ IR
0, 0.1-5Ω GC
0, 0.1-999s AC
0, 0.1-999s DC
0, 0.1-999s IR
0.1-1s GC
0-20mA AC
0-5mA DC
0-50GΩ IR
0-5Ω GC
1-20mA AC
1-5mA DC
0-999s AC
0-999s DC
0-999s IR
0-999s DC
0-999s IR
0-999s AC
0-999s DC
0-999s IR
0, 0.5uA-5mA DC
Program next step
OR
Exit programming