Download
Share
Print this page
KidKraft MEADOWVALE II Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. KidKraft Manuals
  4. Play Sets & Playground Equipment
  5. MEADOWVALE II
  6. Installation and operating instructions manual

KidKraft MEADOWVALE II Installation And Operating Instructions Manual

Play system
Hide thumbs

Advertisement

Quick Links

Download this manual
MEADOWVALE II PLAY SYSTEM - F24035EX
INSTALLATION AND OPERATING INSTRUCTIONS
24'10" / 7.9m
12'10" / 3.9m
4 - 8 Hrs
Two person
assembly
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
customerservice@kidkraft.com
canadacustomerservice@kidkraft.com
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
WARNING
and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 24'10" x 28' (7.9 x 8.5 m) area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6'11" (2.1 m)
CAPACITY - 6 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
Warning. Only for domestic use.
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
europecustomerservice@kidkraft.com
+31 20 305 8620 M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions often

Table of Contents

Warnings and Safe Play Instructions. . . . . . . . . . . . . . . pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance . . . . . . . . . . . . . . . pg. 4
About Our Wood - Limited Warranty . . . . . . . . . . . . . . pg. 5
Keys to Assembly Success . . . . . . . . . . . . . . . . . . . . . . pg. 6
Metric Conversion Sheets . . . . . . . . . . . . . . . . . . . . . pg. 7,8
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 9
Installation of I.D./Warning Plaque . . . . . . . . . . . .Final Step
9404035EX
Rev 06/18/2020

Advertisement

loading

Related Manuals for KidKraft MEADOWVALE II

Summary of Contents for KidKraft MEADOWVALE II

  • Page 1: Table Of Contents

    MEADOWVALE II PLAY SYSTEM - F24035EX INSTALLATION AND OPERATING INSTRUCTIONS WARNING To reduce the risk of serious injury or death, you must read and 24’10” / 7.9m follow these instructions. Keep and refer to these instructions often 12’10” / 3.9m and give them to any future owner of this play system.

  • Page 2: Warnings And Safe Play Instructions

    Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system.

  • Page 3: Protective Surfacing Guidelines

    Protective Surfacing - Reducing Risk of Serious Head Injury From Falls. One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292.

  • Page 4: Instructions For Proper Maintenance

    Instructions for Proper Maintenance Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important that you, the owner, properly maintain it.

  • Page 5: About Our Wood - Limited Warranty

    About Our Wood KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set.

  • Page 6: Keys To Assembly Success

    Keys to Assembly Success Tools Required Shovel Measuring Drill (1/8” Safety Hammer Ratchet 1/2”, Level #2 & #3 Phillips Square Step Tape 3/16” Bit) Glasses 7/16” & 9/16” or Robertson Ruler Ladder Key Number: 2X 012 Post 2 x 4 x 83” represent the step number.

  • Page 9: Part Id

    Part Identification (Reduced Part Size) A1 - A28 (1) CE SW Beam Back 2 x 6 x 69-1/2" Nominal Size Actual Size 3631772 ⅜ 1½" x 5 " 2" x 6" ⅜ ⅜ " x 3 " 2" x 4" ⅜...
  • Page 10 Part Identification (Reduced Part Size) A29 -A36 Nominal Size Actual Size (2) Side Top 1 x 4 x 51-1/2" ⅜ ⅜ " x 3 " 2" x 4" 3641797 ⅜ " x 2½" 2" x 3" 1½" x 1½" 2" x 2" 1"...
  • Page 11 HARDWARE ID (Actual Size) 9277220 (24) Hex Bolt 1/4 x 2" 1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut 9277222 (2) Hex Bolt 1/4 x 2-1/2" 1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut 9277232 (2) Hex Bolt 1/4 x 3-1/2" 1/4"...
  • Page 12 HARDWARE ID (Actual Size) (12) Pan Screw #8 x 1/2" (9264504) (16) Wood Screw #8 x 1-1/8" (9260514) (17) (4) Swing Hanger Cover 5/16" Flat Washer (9300000) (9251300) (75) Wood Screw #8 x 1-1/2" (9260512) (43) (10) Wood Screw #8 x 1-3/4" (9260513) 1/4"...
  • Page 13 If there are any missing or damaged pieces or you need assistance with assembly please contact the consumer relations department directly. Call us before going back to the store. 1.800.933.0771 or 972.385.0100 +31 20 305 8620 europecustomerservice@KidKraft.com customerservice@kidkraft.com For online parts replacement visit canadacustomerservice@kidkraft.com https://parts.kidkraft.eu/ For online parts replacement visit https://parts.kidkraft.com/...
  • Page 14 Step 1: Swing Beam Assembly Fig. 1.3 Hex Bolt Assembly Warning: For your childs safety, Lock T-Nut orientate the swing hangers as Washer shown to ensure your swing will have proper swing motion when installed. Failure to do so could Flat Washer Bolt...
  • Page 15 Step 2: Swing End Assembly Hex Bolt Assembly Lock T-Nut Washer Flat Washer Bolt A: Attach 2 (A35) SW Posts to (A33) SW Upright using 2 (G4) 5/16 x 4” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 2.1) B: Attach (A34) SW Support to both (A35) SW Posts and (A33) SW Upright using 3 (G5) 5/16 x 4-1/2”...
  • Page 16 Step 3: Attach Swing End to Swing Beam A: Place (A32) SW Rail Block in the centre between (A1) CE SW Beam Back and (A2) CE SW Beam Front and attach with 1 (H8) 1/4 x 4-1/4” Hex Bolt (with lock washer, flat washer and t-nut). (fig. 3.1 & 3.2) B: Attach Swing Beam Assembly to the side of the Swing End Assembly with the overhang (fig.
  • Page 17 Step 4: Right Wall Assembly Predrill Pilot Holes for Lag Screw Hex Bolt Assembly Lock T-Nut Predrill 1/8” Pre-drill all pilot holes using a Washer Screw pilot hole 1/8” drill bit before installing the lag screws. Flat Use factory drilled Flat Washer hole as a guide...
  • Page 18 Step 5: Left Wall Assembly Predrill Pilot Holes for Lag Screw Hex Bolt Assembly Pre-drill all pilot holes using a Lock T-Nut Predrill 1/8” Washer Screw pilot hole 1/8” drill bit before installing the lag screws. Flat Use factory drilled Flat Washer hole as a guide...
  • Page 19 Step 6: Fort Assembly A: With both the Left and Right Wall Assemblies facing each other, on the (A20) Corner Posts with the (A12) Lower Diagonals, attach 1 (A24) Top Rope to the outside of the assembly with 2 (H5) 1/4 x 4-1/2” Hex Bolts (with lock washer, flat washer and t-nut).
  • Page 20 Step 7: Attach Lower Back A: Reconfirm that the assembly is square, then attach (A22) Lower Back flush to the bottom of each (A12) Lower Diagonal with 4 (S7) #12 x 2” Pan Screws (with 3/16” flat washer). (fig. 7.1) Step 4 Attach Lower Back Fig.
  • Page 21 Step 8: Attach Side Joist and Centre Divider A: From the inside of the assembly attach (A15) Side Joist to (A24) Tope Rope with 2 (H3) 1/4 x 2-1/2” Hex Bolts (with lock washer, flat washer and t-nut) and 2 (S7) #12 x 2” Pan Screws (with 3/16” flat washer). Bolts and screws are to be installed from the outside of the assembly.
  • Page 22 Step 9: Attach Lower Front and Rock Rails A: Attach 1 (A18) Corner Block flush to the bottom and side of 1 (A11) Rock Rail with 2 (S4) #8 x 3” Wood Screws as shown in fig. 9.1. Step 6 Attach Lower Front & Rock Diagona B: Attach the (A11) Rock Rail from Step 9A, 5/8”...
  • Page 23 Step 10: Attach Gusset Step 7 Attach Gusset A: Make sure assembly is square and then place 1 (A10) Gusset tight to the under side of (A17) Floor Front and to (A20) Corner Post from the inside of the assembly. Make sure the gusset is flush to the outside of the post and attach with 2 (S4) #8 x 3”...
  • Page 24 Step 11: Rock Wall Assembly A: Flush to the tops and outside edges of each (A11) Rock Rail attach 1 (A7) CE Access Board with 4 (S2) #8 x 1-1/2” Wood Screws. (fig. 11.1) B: Evenly space 3 (A5) CE Rock Board B and 2 (A6) CE Rock Board A and attach to each (A11) Rock Rail with 4 (S2) #8 x 1-1/2”...
  • Page 25 Step 11: Rock Wall Assembly cont. Step 8b Rock Wall Asy C: Place 1 rock on each (A5) and (A6) CE Rock Board (fig. 11.2) and attach using the included hardware. The screw must be in the hole directly under the Pan Bolt. It will stop the rock from spinning. (fig. 11.3) Fig.
  • Page 26 Step 12: Floor Assembly A: From the inside of the assembly measure 3-1/8” down from top of each (A14) SW Floor End then attach (A16) Floor Joist to each board with 1 (S4) #8 x 3” Wood Screws per end. (fig. 12.1, 12.2 and 12.3) B: Attach 1 (A8) Centre Board to (A17) Floor Front, (A16) Floor Joist and (A15) Side Joist with 5 (S2) #8 x 1-1/2”...
  • Page 27 Step 12: Floor Assembly cont. Step 9b Floor Asy D: In between (A3) CE Gap Boards and (A8) Centre Board place 4 (A4) Floor Boards making sure all boards are evenly spaced. Attach to (A15) Side Joist, (A16) Floor Joist and (A17) Floor Front using 5 (S2) #8 x 1-1/2” Wood Screws per board.
  • Page 28 Step 13: Attach Roof Supports A: Attach 1 (A30) Tarp Support to (A29) Side Top and (A14) SW Floor on the Right Wall side of the assembly with 2 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut). The support should be flush to the bottom of (A14) SW Floor.
  • Page 29 Step 14: Attach SL Spacer A: In between (A20) Corner Post and (A11) Rock Rail attach 1 (A21) SL Spacer to (A17) Floor Front with 4 (S3) #8 x 2-1/2” Wood Screws. (A21) SL Spacer is flush to the top of the floor boards and tight to (A11) Rock Rail. (fig.
  • Page 30 Step 15: Attach Wall Boards A: On both sides of (A30) Tarp Support attach 2 (A9) Cedar Walls to (A29) Side Top and (A14) SW Floor with 4 (S1) #8 x 1-1/8” Wood Screws per board. Make sure the bottom of the boards are tight against the gap boards and the bevelled edges to the top, facing out.
  • Page 31 Step 16: Attach Tarp Frame and Hand Grips Predrill Pilot Holes for Lag Screw Pre-drill all pilot holes using a Predrill 1/8” Screw pilot hole 1/8” drill bit before installing the lag screws. Flat Use factory drilled Washer hole as a guide tep 12 Attach Tarp Frame A: Attach (A26) Ridge to (A30) Tarp Support and flush to end of (A31) SW Mount using 3 (S3) #8 x 2-1/2”...
  • Page 32 Step 17: Attach Canopy A: Place Canopy over (A26) Ridge making sure bottom edges of Canopy are even on both sides of assembly. (fig. 17.1) B: Secure one side by attaching Canopy to 1 (A28) Top End using 5 (S5) #8 x 1/2” Pan Screws (with #8 flat Step 13 Attach Roof washer).
  • Page 33 Step 18: Attach Swing Assembly and Swings MOVE FORT TO FINAL LOCATION. FINAL LOCATION MUST BE ON LEVEL GROUND Step 16 Attach Swing Asy and Swings A: Attach Swing Assembly from Step 3 to (A31) SW Mount with 1 (G5) 5/16 x 4-1/2” Hex Bolt (with lock washer, flat washer and t-nut) and 1 (GL8) 5/16 x 2”...
  • Page 34 Step 19: Attach Rope Ladder A: Attach Rope Ladder to (A24) Top Rope and (A22) Lower Back as shown in fig. 19.1. Make sure the top and bottom rungs have at least a 9-1/4” clearance. Tie each end of the rope as shown in fig. 19.2 & 19.3. B: Secure the top knots with 2 Cable Ties per rope as shown in fig.
  • Page 35 Step 20: Attach Slide and Acro Swing Note: Pre-drill all holes using a 1/8” drill bit before installing the pan screws. 8 Attach Rope Ladder A: Place Slide in the centre between (A20) Corner Post and (A13) Centre Divider. (fig. 20.1) B: Pre-drill 1/8”...
  • Page 36 Step 21: Attach Ground Stakes If Bolt protrudes Warning! Check entire play centre for beyond T-Nut bolts protruding beyond T-Nuts. Use extra washers to eliminate this condition. Use an extra Flat Washer A: Drive 1 (A36) Ground Stake 10-1/2” into the ground at each (A35) SW Post on the inside of the assembly and attach with 2 (S3) #8 x 2-1/2”...
  • Page 37 NOTES...
  • Page 38 NOTES...
  • Page 39 NOTES...
  • Page 40 Would you recommend the purchase of our products to friends and family? Comments: MAIL TO: Fill out your registration card online at KidKraft Netherlands BV https://prdregistration.kidkraft.com/ Olympisch Stadion 8 1076 DE Amsterdam The Netherlands KidKraft would like to say Thank You for Attention: Customer Service your time and feedback.

This manual is also suitable for:

F24035ex