Sharp MX-2314N Service Manual page 291

Report code
Display in the column of
(Communication
result
result)
0 – 31 Refer to "previous table".
33 BUSY
34 CANCEL
35 NG35 XXXX
36 (No record paper)
37 (Record paper jam)
38 MEM. FULL
39 (Number of paper
unmatched)
40 (Relay not received)
41 LENGTH OVER
42 LENGTH OVER
43 (Communication) (OK)
44 ORIGINAL ERROR
45 (Picture quality error)
46 NO RESPONSE
47 TX DECODE ERROR
48 OK
OK REPLY RECEIVE
49 NO RX POLL
50 RX POLL FAIL
51 PASS # NG
52 (No confidential function in
remote party)
53 (Confidential not received)
54 (Confidential BOX NO NG)
55 (No relay function in
remote party)
56 NO REL RX
57 (Relay ID unmatched)
58 REJECTED
59 RX NO F-CODE POLL
60 NO F-CODE POLL
61 RX POLL # NG
62 F POLL PASS # NG
63 NO F FUNC
64 NO F-CODE
67 F PASS # NG
68 BOX NO. NG
69 MEMORY OVER
70 (JOB MEMORY OVER)
*1
71 NG71 XXXX
72 (NG72 XXXX)
*1
73 NG73 XXXX
*1
74 NG74 XXXX
Depends on the point of communication interruption. For 16 or later, V.34 mode communication.
The calling side cannot establish connection with the remote party.
A communication interruption command is made during sending/receiving. The interruption key is pressed for
interruption of input. <Send/Receive/Polling/Bulletin board>
Power is failed during sending/receiving. <Send/Receive/Polling/Bulletin board>
Memory over during reception. <Receive/Polling>
Print is not made during reception in acting reception inhibit. <Receive/Polling>
The send data length of one page exceeds the limit (2m) in sending. <Send/Bulletin board>
The receive data length of one page exceeds the limit. <Receive/Polling>
Speaking before data transmission
A document jam occurs in direct sending. <Send>
The FAX signal from the remote party is not detected within T1 time. <Send/Polling>
(When in recall, however, the recall setting in case of a communication error is valid.)
A decode error occurs in the FAX board. <Send/Bulletin board>
Normal end of communication
OK in Internet FAX send with reception confirmation.
The called side does not have polling function in polling reception. <Polling>
The called side has no data to send. <Polling>
In polling reception, DCN is received for DTC. <Polling>
In polling sending, there is no send data. <Bulletin board>
In poling sending, the allow number is not matched. <Bulletin board>
In polling sending, the system number is not matched. <Bulletin board>
In confidential sending, the remote party does not have confidential function. <Send>
(Including other company's machines)
1) The NSF signal has not "Confidential function" bit.
2) The NSF is not a Sharp machine.
1) In confidential sending, DCN is received for NSS. <Send>
1) In confidential reception, a confidential box number which is not registered is specified.
In relay command sending, the remote machine has no relay function. <Send>
(Including other company's machine)
1) The NSF signal has not "Confidential function" bit.
2) The NSF is not a Sharp machine.
1) In relay command sending, DCN is received for NSS. <Send>
2) In relay command reception, a remote station number which is not registered is specified. <Receive>
3) In F code relay broadcasting, an F code relay command is received.<Receive>
1) In relay command reception, the relay ID does not match. <Receive>
In reception, data are sent from a remote machine of receive inhibit number. <Receive>
(Not rejected in the bulletin board send or the F code bulletin board send.)
In F code polling (calling), the remote machine has no DIS bit 47 (polling function). <Polling>
In F code polling (calling), the called side has no send data. (DIS bit 9 is 0.)<Polling>
In F code polling (calling), DCN is received for SEP. <Polling>
In bulletin board, there is no send data for SEP. <Bulletin board>
In bulletin board, the sub address (bulletin board number (SEP)) is not matched. <Bulletin board>
In bulleting board, the pass code (PWD) is not matched. <Bulletin board>
In F code sending, the remote machine has no DIS bit 49 (sub address function). <Send>
(Check that the remote machine conforms to F code.)
In F code sending : <Send>
1) DCN is received for SUB. --- Check the box number.
2) DCN is received for SID. --- Check the box number and pass code.
In F code receiving : <Receive>
"F code relay broadcasting" or "F code confidential reception" is "Inhibited with soft SW."
In F code receiving, the pass code (SID) is not matched. <Receive>
In F code reception, a box number which is not registered is specified. (SUB is not matched.) <Receive>
Memory over in quick online sending <Send>
In PC-FAX reservation, the number of remote parties is exceeded. <Send>
In PC-FAX reservation, data sent from PC includes some errors. <Send>
*1
In department management setting on the machine side:
• In reservation from PC-FAX or PC-Internet FAX, a department number which is not registered on the
machine side is specified. <Send>
• In reservation from PC-FAX or PC-Internet FAX, the department number is not specified. <Send>
In reservation from PC-FAX or PC-Internet FAX, the use quantity limit is exceeded. <Send>
When reserving specified filing in document filing in PC-FAX or PC-Internet FAX;
• The pass-code for the folder is set on the machine side and the pass-code from PC-XXX does not match
with it. <Send>
• The pass-code for the folder is set on the machine side and no pass-code is specified by PC-XXX. <Send>
MX3114N TROUBLESHOOTING 7 – 36
Content of communication interruption