Sharp MX-2310U Installation Manual

Sharp MX-2310U Installation Manual

Digital full color multifunctional system
Hide thumbs Also See for MX-2310U:

Advertisement

[1]
CONFIGURATION . . . . . . . . . . . . . . . . 1-1
[2]
MX-2310U (MAIN UNIT). . . . . . . . . . . . 2-1
[3]
Dehumidifying heater . . . . . . . . . . . . . . 3-1
[4]
(STAND/1x500/2x500/3x500 SHEET
PAPER DRAWER) . . . . . . . . . . . . . . . . . 4-1
[5]
AR-SU1 (STAMP UNIT) . . . . . . . . . . . . 5-1
[6]
MX-FN17 (FINISHER) . . . . . . . . . . . . . 6-1
[7]
[8]
MX-TR12 (EXIT TRAY UNIT) . . . . . . . 8-1
[9]
[13] MX-PB14 (PRINTER EXPANSION KIT) . . 13-1
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.

INSTALLATION MANUAL

DIGITAL FULL COLOR
MULTIFUNCTIONAL SYSTEM
MODEL
CONTENTS
SHARP CORPORATION
CODE: 00ZMX2310/I1E
MX-2310U
(INTERNET FAX EXPANSION KIT) . 16-1
(APPLICATION INTEGRATION
MODULE) . . . . . . . . . . . . . . . . . . . . . 17-1
(APPLICATION COMMUNICATION
MODULE) . . . . . . . . . . . . . . . . . . . . . 18-1
(EXTERNAL ACCOUNT MODULE) . . 19-1
Enable setting . . . . . . . . . . . . . . . . . . 20-1
machine . . . . . . . . . . . . . . . . . . . . . . 23-1
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.

Advertisement

Table of Contents
loading

Summary of Contents for Sharp MX-2310U

  • Page 1: Table Of Contents

    CONFIGURATION ....1-1 [15] MX-PK11 (PS3 EXPANSION KIT) . . 15-1 MX-2310U (MAIN UNIT)... . 2-1 [16] MX-FWX1 (INTERNET FAX EXPANSION KIT) .
  • Page 2: Transit, Installation (Using) Environment, Note

    [20] Remote operation panel function Enable setting [2] MX-2310U (MAIN UNIT) 1. General ....... . . 20- 1 1.
  • Page 3 Symbols in this manual The lists of symbols used in this manual are shown below. The meaning of each symbol described in the table must be understood for proper servicing. 1. Symbols used for notes and Symbol Meaning OK/GOOD Indicates a correct cautions procedure or result in an adjustment, etc.
  • Page 4 Symbol Meaning (Work content) Symbol Meaning (Work content) Cleaning Indicates that cleaning is Engage the pawl. (Vacuum) performed with a vacuum cleaner. Cleaning Indicates that cleaning is Screw lock Indicates that a screw is (Brush) performed with a brush. secured with adhesive. Indicates that oil is Unlock applied to lubricate.
  • Page 5: Machine

    (An electrical work is required.) Use of a step-up transformer is also available. In this case, the capacity must be great enough for the max. power consumption of the machine. MX-2310U Transit, Installation (using) environment, Note – i...
  • Page 6 (5) Vibration Avoid installation near a machine which produces vibrations. If vibrations are applied to the copier machine, copy images may be deflected and a trouble may be caused. MX-2310U Transit, Installation (using) environment, Note – ii...
  • Page 7: Transit And Delivery

    Since the hard disk drive is built in the machine, use care not to exert vibrations or shocks to the machine when in transit. B. Delivery Remove the packing materials prior to installation in the office envi- ronment. MX-2310U Transit, Installation (using) environment, Note – iii...
  • Page 8: System Diagram

    SHARPDESK 10 LICENSE SHARPDESK 50 LICENSE DATA SECURITY KIT EXPANSION KIT MX-USA0 MX-AMX2 MX-AMX3 MX-AMX1 MX-SM10 MX-SCX1 SHARPDESK 100 LICENSE APPLICATION EXTERNAL ACCOUNT EXPANSION MEMORY STAPLE CARTRIDGE APPLICATION COMMUNICATION MODULE MODULE INTEGRATION MODULE BOARD AR-SV1 STAMP CARTRIDGE MX-2310U CONFIGURATION 1 – 1...
  • Page 9: Option List

    STD: Standard equipment OPT: Installable option *1: The printer expansion kit is required. *2: Memory expansion is required. *3: No support for some destinations. *4: Supply parts *5: Required when the XPS printer is used. MX-2310U CONFIGURATION 1 – 2...
  • Page 10: Unpacking

    [2] MX-2310U (MAIN UNIT) MX-2310U Service Manual Unpacking A. Unpacking C. Check the packed items B. Removal of the fixing tape and protection material Name Quantity Developer Operation manual MX-2310U MX-2310U (MAIN UNIT) 2 – 1...
  • Page 11: Installation

    (2) Scanner (2/3 mirror unit) lock release Remove the optical unit fixing screw, and remove the note label. Turn the drum cover securing locks (2) to release, and then raise the drum positioning cove. MX-2310U MX-2310U (MAIN UNIT) 2 – 2...
  • Page 12 OPC drum unit, put your hand from below the unit and slide it in parallel along the guide on the right side. At that time, be careful not to touch the OPC drum surface. MX-2310U MX-2310U (MAIN UNIT) 2 – 3...
  • Page 13 Turn ON the main power switch of the machine and the power switch on the operation panel. Enter the SIM25-2 mode. Detach the LSU cleaning bar from the front cover. After entering the simulation, close the front cabinet. MX-2310U MX-2310U (MAIN UNIT) 2 – 4...
  • Page 14 When the "Type" is other than plain paper, recycled paper, colored paper, or a user type, [Fax] and [Internet Fax] Open the front cabinet, and insert each toner cartridge. cannot be selected. MX-2310U MX-2310U (MAIN UNIT) 2 – 5...
  • Page 15: Image Quality Check

    Used to set YES/NO of counting when non-print paper is passed through each counter. Used to set YES/NO of user calibration permission. Used to set the limit number of sheets for stapling. MX-2310U MX-2310U (MAIN UNIT) 2 – 6...
  • Page 16 * "ALL_ROTATES" shows the number of rotations of adjust- ments for all the adjustment screws. "C, M, and Y(SKEW)" shows the number of adjustment click steps for each adjust- ment screw of C, M, and Y. MX-2310U MX-2310U (MAIN UNIT) 2 – 7...
  • Page 17 In this case, check each drive section and the process section. Serviceman chart (Color patch section) The densities of patches 1 - 6 of Patch 7 is slightly each color are properly balanced. copied or not copied. MX-2310U MX-2310U (MAIN UNIT) 2 – 8...
  • Page 18 Resolution Resolution Color difference in gray balance between the F and the R sides No white and black streaks Background density Resolution Registration Void Void Color text reproduction capability Resolution Resolution Void Void MX-2310U MX-2310U (MAIN UNIT) 2 – 9...
  • Page 19 The black low-density gradation is copied slightly. great. Void Void Resolution Resolution Density difference between the F and the R sides. No white and black streaks Resolution Void Void Low-density gradation Background density Resolution Resolution Void Void MX-2310U MX-2310U (MAIN UNIT) 2 – 10...
  • Page 20 Magenta, it means that the adjustment is proper. In an actual print mode, it is converted into the natural gray color balance by the color table. (When the color balance target is DEF 1.) MX-2310U MX-2310U (MAIN UNIT) 2 – 11...
  • Page 21 5 sheets of white paper on the printed color patch image (adjustment pattern). Press [EXECUTE] key. The printer color patch image (adjustment pattern) is printed out. (A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.) MX-2310U MX-2310U (MAIN UNIT) 2 – 12...
  • Page 22 SIM 67-27, if the color balance is adjusted to that color balance, select the [SERVICE] target. Wait until [EXECUTE] key is displayed. When it is displayed, press it. The half tone image correction is performed. MX-2310U MX-2310U (MAIN UNIT) 2 – 13...
  • Page 23 Troubleshoot the cause, repair or perform necessary works, and repeat the adjustment from the beginning. If color balance or density is not satisfied, adjust the copy and printer color balance by SIM 46-74. MX-2310U MX-2310U (MAIN UNIT) 2 – 14...
  • Page 24: Parts List

    Heater (120V series) RHETP0166FCPZ (120V series) Heater (230V series) RHETP0167FCPZ DKIT-0426FC11 Heater mounting plate LPLTM6089FCZZ (230V series) Heater mounting plate LPLTM8118FCZZ Screw (M3 x 6 S-tight) XHBS730P06000 Screw XEBS740P10000 Screw XBPS730P08KS0 Clamp LHLDW1013FCZZ CSS-WH harness DHAI-4711FCPZ MX-2310U Dehumidifying heater 3 – 1...
  • Page 25 Desk heater (120V series) RHETP0144FCZZ Desk heater (200V series) RHETP0139FCZZ Cassette high temperature caution label TLABZ5459FCZZ Screw (M4 x 8) XBPS740P08K00 Screw (M3 x 4 S tight bind) XHBS730P04000 Screw (M3 x 6 S tight bind) XHBS730P06000 MX-2310U Dehumidifying heater 3 – 2...
  • Page 26 Desk heater (120V series) RHETP0144FCZZ Desk heater (200V series) RHETP0139FCZZ High temperature caution label TLABZ5459FCZZ Screw (M4 x 8) XBPS740P08K00 Screw (M3 x 4 S tight bind) XHBS730P04000 Screw (M3 x 6 S tight bind) XHBS730P06000 MX-2310U Dehumidifying heater 3 – 3...
  • Page 27: Installation

    Connect the WH harness, and attach the earth wire. Pass the WH harness under the CCS-WH harness to the switch. Remove the left cabinet lower. CSS-WH harness WH harness Attach the AC cord plate. MX-2310U Dehumidifying heater 3 – 4...
  • Page 28 Attach the heater mounting plate to the T-Heater cover and secure it with the screw (M3 x 6 S-tight). Attach the CSS-WH harness to the heater mounting plate, and connect the harness of the dehumidifier heater. Fix the earth wire with a screw. MX-2310U Dehumidifying heater 3 – 5...
  • Page 29 Install the left cabinet. unit frame. Fix the earth wire with a screw. Connect the connector. Install the rear cabinet. Pass the WH harness under the CCS-WH harness to the switch. CSS-WH harness WH harness MX-2310U Dehumidifying heater 3 – 6...
  • Page 30 Remove the paper exit cover. Remove the left cabinet. (2) SCN-WH harness connection Remove the harness guide. Remove the left cabinet upper. Connect the SCN-WH harness connector to the scanner frame. Remove the rear upper cabinet. MX-2310U Dehumidifying heater 3 – 7...
  • Page 31 (5) Installation of the scanner heater unit Attach the clamp to the scanner frame. Extend the harness, and secure the other position of it with banding band. When installing, be careful to prevent damage of the wire. MX-2310U Dehumidifying heater 3 – 8...
  • Page 32 Attach the rear cabinet. Tighten the loose scanner heater harness by pulling it in the arrow direction and secure it with the snap band then cut its tip to approx. 5 mm or less. MX-2310U Dehumidifying heater 3 – 9...
  • Page 33 Attach the edge wire saddle and the desk heater mounting plate to the heater radiating plate, and fix them with a screw (M3 x 4). Pass the desk heater harness through the edge wire saddle. Attach the paper exit cover. MX-2310U Dehumidifying heater 3 – 10...
  • Page 34 Attach the snap band of the heater harness to the frame. Fix the earth wire to the frame with a screw (M4 x 8). Attach the connector cover. (5) Heater harness 2 attachment Remove the mounting plate. Attach the mounting plate. MX-2310U Dehumidifying heater 3 – 11...
  • Page 35 Pass the harness of the heater unit for the tray 2 through the hole in the frame. Attach the heater unit for the tray 2 to the frame, and fix it with a screw (M3 x 6). MX-2310U Dehumidifying heater 3 – 12...
  • Page 36 Attach the right rear cabinet and the rear cabinet. (9) Connection to the machine Remove the rear cabinet cover of the machine. (11) Paper feed tray attachment Attach the paper feed tray. Connect the heater harness to the machine harness. MX-2310U Dehumidifying heater 3 – 13...
  • Page 37 AC terminal (L side), and between the earth terminal and AC terminal (N side) with the circuit tester, and confirm they are not short-circuited. When not using the dehumidifier heater after checking, turn off the dehumidifier heater switch. MX-2310U Dehumidifying heater 3 – 14...
  • Page 38 Attach the right adjuster included in the package to the desk unit. Insert the right adjuster until it is locked. Name Quantity Desk unit Right adjuster Turn each adjuster to fix the desk unit. Fixing screws (M3 x 8) Connection cover MX-2310U MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER) 4 – 1...
  • Page 39 Raise the linkage plates on the right and left sides of the rear Remove the tray 1 and the tray 2. side of the desk unit, and fix them with the fixing screws included in the package. MX-2310U MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER) 4 – 2...
  • Page 40 D. Connector connection For setting the tray size, refer to “Tray size setup” (1-6). Remove the cover from the rear side of the machine. MX-2310U MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER) 4 – 3...
  • Page 41 • [LEAD]: Print image lead edge image position adjustment • [OFFSET]: Print image off-center adjustment When [ALL] is selected, both of the above two items are executed simultaneously. Select a paper feed tray to be adjusted. MX-2310U MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER) 4 – 4...
  • Page 42: Ar-Su1 (Stamp Unit)

    A. Removal of the RSPF unit Remove the rear upper cabinet. Put the RSPF unit on a stable table with the OC mat upside. MX-2310U AR-SU1 (STAMP UNIT) 5 – 1...
  • Page 43 Place the harness of the scanner home position sensor at the back of the guide and the RSPF harness. Check to confirm that the connector of the scanner home position sensor is securely connected. Install the sensor cover. MX-2310U AR-SU1 (STAMP UNIT) 5 – 2...
  • Page 44 Connect the power plug of the machine to the power outlet, and turn ON the main power switch and the operation panel power switch. F. Installation check Use SIM22-10 to check to confirm that the finish stamp (AR- SU1) is recognized. MX-2310U AR-SU1 (STAMP UNIT) 5 – 3...
  • Page 45: Mx-Fn17 (Finisher)

    Screw (M3 x 6 S tight, with flange) Screw (M4 x 6 S tight) Screw (M3 x 6 S tight) Clip Fulcrum shaft Staple position label (For the scanner) Staple position label (For the RSPF) Safety cover Protection sheet MX-2310U MX-FN17 (FINISHER) 6 – 1...
  • Page 46 C. Installation of the parts included Attach the safety cover to the attachment, and fix it with the screw (M3 x 6 S tight, with flange). Remove the paper exit tray. Attach the attachment. Remove the left cabinet. MX-2310U MX-FN17 (FINISHER) 6 – 2...
  • Page 47 M3 x 6 S tight, with flange). Install the front cabinet upper. Attach the punch F cover and fix it with the screw (M3 x 6 S tight). Attach the blind bottom plate. MX-2310U MX-FN17 (FINISHER) 6 – 3...
  • Page 48 R end reference 0 - 3mm E. Installation of the finisher Remove the package supporting plate from the finisher. D. External fitting attachment Remove the left cabinet upper rear from the left cabinet upper. MX-2310U MX-FN17 (FINISHER) 6 – 4...
  • Page 49 Attach the staple position label (for the scanner). First label Fit with the corner R. Fit with the corner R. Label attachment reference * Corner of the upper cabinet bottom MX-2310U MX-FN17 (FINISHER) 6 – 5...
  • Page 50 Attach the staple position label (for the RSPF). H. Turn ON the power of the main unit Connect the power plug of the machine to the power outlet, and turn ON the main power switch and the operation panel power switch. MX-2310U MX-FN17 (FINISHER) 6 – 6...
  • Page 51: Mx-Pn11A/B/C/D (Punch Module)

    Remove the punch F cover. MX-2310U MX-PN11A/B/C/D (PUNCH MODULE) 7 – 1...
  • Page 52 B. Installation of the punch unit Install the punch unit. Attach the fulcrum cover. D. Label attachment C. Install of the open/close cover Attach the punch dust label. Install the punch F cover. MX-2310U MX-PN11A/B/C/D (PUNCH MODULE) 7 – 2...
  • Page 53 E. Turn ON the power of the main unit Connect the power plug of the machine to the power outlet, and turn ON the main power switch and the operation panel power switch. MX-2310U MX-PN11A/B/C/D (PUNCH MODULE) 7 – 3...
  • Page 54: Mx-Tr12 (Exit Tray Unit)

    Attach the right paper exit cover included in the package, and A. Installation of the right paper exit unit fix it with the screw. Connect the connector. Remove the connector cover. Install the connector cover. MX-2310U MX-TR12 (EXIT TRAY UNIT) 8 – 1...
  • Page 55 Connect the power plug of the machine to the power outlet, and turn ON the main power switch and the operation panel power switch. D. Tray setting Use SIM26-1 to set the tray YES/NO. MX-2310U MX-TR12 (EXIT TRAY UNIT) 8 – 2...
  • Page 56: Mx-Fx11 (Facsimile Expansion Kit)

    A. FAX unit installation Remove the two screws on the rear cabinet of the main unit. Attach the step screw (included in the package) to one of the Remove the shield plate. removed screw positions. MX-2310U MX-FX11 (FACSIMILE EXPANSION KIT) 9 – 1...
  • Page 57 E. Turn ON the power of the main unit Connect the power plug of the machine to the power outlet, and turn ON the main power switch and the operation panel power switch. MX-2310U MX-FX11 (FACSIMILE EXPANSION KIT) 9 – 2...
  • Page 58: Mx-Sm10

    Remove the left cabinet. When handling an expansion memory board, be careful not to touch the terminals. Remove the shield plate. Avoid diagonal insertion of the expansion memory board for the slot. MX-2310U MX-SM10 (EXPANSION MEMORY BOARD) 10 – 1...
  • Page 59 At that time, check to confirm that the hooks on the left and the right sides of the slot are securely locked. C. Shield plate and left cabinet installation Install the shield plate. MX-2310U MX-SM10 (EXPANSION MEMORY BOARD) 10 – 2...
  • Page 60: Mx-Pf10 (Barcode Font Kit)

    Font No. Font name Code128TT-Regular Code128-NarrowTT-Regular Code128-WideTT-Regular Code39HalfInch-Regular Code39OneInch-Regular Code39QuarterInch-Regular Code39SmallHigh-Regular Code39Slim-Regular Code39SmallLow-Regular Code39SmallMedium-Regular Code39Wide-Regular Codabar-Regular Interleaved2of5-Regular Interleaved2of5-Thin-Regular OCR-A OCR-B OCR-B-C39-Regular UPC-Half UPC-Half-Bars UPC-HalfMusic UPC-HalfNarrow UPC-HalfThin UPC-Tall-Regular UPC-TallBarsThin-regular UPC-TallMusicThin-Regular UPC-TallNarrow-Regular UPC-TallThin-regular ZipCodeBarcode-Regular MX-2310U MX-PF10 (BARCODE FONT KIT) 11 – 1...
  • Page 61: Mx-Fr25U (Data Security Kit)

    Install an program ROM to the OPT ROM slot of the MFP con- does not light up or blink when performing installation. trol PWB. OPT ROM Set the BOOT SW on the left upper side of the MFP control PWB to OFF. MX-2310U MX-FR25U (DATA SECURITY KIT) 12 – 1...
  • Page 62 Turn ON the main power switch and the power switch on the operation panel. F. Confirmation of function enable Execute SIM22-10 (Machine configuration display) to check to con- firm that the set functions are enable. MX-2310U MX-FR25U (DATA SECURITY KIT) 12 – 2...
  • Page 63: Mx-Pb14 (Printer Expansion Kit)

    Install the driver, and make necessary settings. Execute SIM22-10 to check to confirm that the combined machine recognizes the MX-PB14. Use SIM46-74 to execute the copy/printer color balance den- sity adjustment. Be sure to execute this adjustment. MX-2310U MX-PB14 (PRINTER EXPANSION KIT) 13 – 1...
  • Page 64: Mx-Pux1 (Xps Expansion Kit)

    Turn ON the main power switch and the power switch on the operation panel. B. Confirmation of function enable Execute SIM22-10 (Machine configuration display) to check to con- firm that the set functions are enable. MX-2310U MX-PUX1 (XPS EXPANSION KIT) 14 – 1...
  • Page 65: Mx-Pk11 (Ps3 Expansion Kit)

    Turn ON the main power switch and the power switch on the operation panel. B. Confirmation of function enable Execute SIM22-10 (Machine configuration display) to check to con- firm that the set functions are enable. MX-2310U MX-PK11 (PS3 EXPANSION KIT) 15 – 1...
  • Page 66: Mx-Fwx1

    Turn ON the main power switch and the power switch on the operation panel. B. Confirmation of function enable Execute SIM22-10 (Machine configuration display) to check to con- firm that the set functions are enable. MX-2310U MX-FWX1 (INTERNET FAX EXPANSION KIT) 16 – 1...
  • Page 67: Mx-Amx1

    Turn ON the main power switch and the power switch on the operation panel. B. Confirmation of function enable Execute SIM22-10 (Machine configuration display) to check to con- firm that the set functions are enable. MX-2310U MX-AMX1 (APPLICATION INTEGRATION MODULE) 17 – 1...
  • Page 68: Mx-Amx2

    Turn ON the main power switch and the power switch on the operation panel. B. Confirmation of function enable Execute SIM22-10 (Machine configuration display) to check to con- firm that the set functions are enable. MX-2310U MX-AMX2 (APPLICATION COMMUNICATION MODULE) 18 – 1...
  • Page 69: Mx-Amx3

    Turn ON the main power switch and the power switch on the operation panel. B. Confirmation of function enable Execute SIM22-10 (Machine configuration display) to check to con- firm that the set functions are enable. MX-2310U MX-AMX3 (EXTERNAL ACCOUNT MODULE) 19 – 1...
  • Page 70: Remote Operation Panel Function Password Setting Procedures

    The entered password is displayed on the column of "NEW." To modify the entered password, use clear key to delete the password digit by digit. Press [SET] key, and the password is set. MX-2310U Remote operation panel function Enable setting 20 – 1...
  • Page 71: Setting, Adjustments, Operation Check

    Stapling operation When the finisher is installed Grouping operation When the finisher is installed Sorting operation When the finisher is installed Paper exit operation When the exit tray unit (MX-TRX2) is installed MX-2310U Setting, Adjustments, Operation check 21 – 1...
  • Page 72: Setup And Adjustment Data Recording

    • In case of a memory trouble, if the data are not kept, all the adjustments must be made again. • If the data are kept, the setup values and the adjustment values can be entered without adjustments, shortening the servicing time. MX-2310U Setup and adjustment data recording 22 – 1...
  • Page 73: Necessary Works Before Moving The Machine

    • Scanner (Optical section) • Paper cassette lift plate Since the hard disk drive is built in the machine, use care not to exert vibrations or shocks to the machine when in transit. MX-2310U Necessary works before moving the machine 23 – 1...
  • Page 74 LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: <Solder composition code of lead-free solder> Solder composition Solder composition code Solder composition...
  • Page 75 CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
  • Page 76 Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated. PCL is a registered trademark of the Hewlett-Packard Company. Sharpdesk is a trademark of Sharp Corporation. All other trademarks and copyrights are the property of their respective owners. SHARP CORPORATION...

Table of Contents