Sharp MX-2314N Service Manual page 169

Toner
Destination
preparation preparation
message
EUROPE 0 4 (Displayed
(Displayed) when the
toner
remaining
quantity is
25%.)
U.K. 0 4 (Displayed
(Displayed) when the
toner
remaining
quantity is
25%.)
AUS. 0 4 (Displayed
(Displayed) when the
toner
remaining
quantity is
25%.)
AB_A 0 4 (Displayed
(Displayed) when the
toner
remaining
quantity is
25%.)
CHINA 0 4 (Displayed
(Displayed) when the
toner
remaining
quantity is
25%.)
(Contents of set items)
A: Enable/Disable setting of the toner preparation message display.
B: The toner remaining quantity at which the toner preparation
message is displayed.
C: Enable/Disable setting of the toner preparation message display
when the toner near end status is reached.
D: Machine operation at toner end
E: Number of allowable copy/print/FAX when the toner near end
message is displayed. (Range: 0 - 50 sheets)
The number of output print allowed in item D is based on the
assumption that the sheets are of A4 size with print ratio of 5%.
(The number of outputs allowed differs depending on the paper
size and the print ratio.)
When item A is set to "0" and item E is properly set, printing can be
made after toner near end. However, improper phenomena such as
insufficient density, thin spots, or improper color balance may result
depending on the using conditions. When item E is set to "1" print-
ing is disabled after toner near end. In this case, toner end display
is made in the toner near end status, and copy/print/FAX outputs
are disabled.
26-73
Purpose Setting
Function (Purpose) Enlargement continuous shoot, A3 wide
copy mode image loss (shade delete quan-
tity) adjustment
Section
Operation/Procedure
1) Select an item to be set with scroll keys.
2) Enter the set value with 10-key.
3) Press [OK] key.
Setting value
Enable/
Toner Toner near Disable of
end print job
time message continuation
at toner end
0 2
(Displayed) (Print
operation
stopped)
0
(Displayed)
0
(Displayed)
0
(Displayed)
0 1
(Displayed) (Print
operation
continued)
MX-3114N SIMULATION 6 – 36
When the adjustment value is increased, the image loss
(shade delete quantity) is increased.
Item/Display Content
A DELETING Rear frame side
SHADOW ADJ image loss quantity
(M) (shade delete
quantity) adjustment
B DELETING Lead edge image
SHADOW ADJ (S) loss quantity (shade
delete quantity)
adjustment
26-74
Purpose Setting
Function (Purpose) Used to set the OSA trial mode.
Section
Operation/Procedure
1) Enter the set value with 10-key.
2) Press [OK] key.
Item/Display
A OSA TRIAL MODE 0 Used to set the
(0: YES 1: NO) OSA trial mode.
1 OSA trial mode is
canceled.
26-78
Purpose Setting
Function (Purpose) Used to set the password of the remote
operation panel.
Section
Operation/Procedure
1) Enter a password with 10-key. (5 - 8 digits)
The entered password is displayed on the column of "NEW".
In order to correct the entered password, press the [clear] key
to delete the entered value one digit by one digit.
2) Press [SET] key.
26-79
Purpose Setting
Function (Purpose) Used to set YES/NO of the pop-up display
of user data delete result.
Section
Operation/Procedure
1) Enter the set value with 10-key.
The value for the display operation specification after comple-
tion of user data delete is set.
2) Press [OK] key.
Item/Display Content
A DISP SET User data delete result
pop-up display ON
User data delete result
pop-up display OFF
Setting
Default value
range
0 - 50 0
(Adjustment
amount:
0.1mm/step)
0 - 50 0
(Adjustment
amount:
0.1mm/step)
Setting Default
Content
range value
0 - 1 1
Default
Setting range
value
YES 1 0 (NO)
NO 0