Sharp MX-2314N Service Manual page 229

53-9
Purpose Adjustment
Function (Purpose) Used to set dirt detection for RSPF scan-
ning position.
Item/Display
A DIRT_ALARM_SET
B SIDEA_SCAN_POSITION_SET_START
C SIDEA_SCAN_POSITION_SET_JOB
D SIDEA_SCAN_POSITION_LV
E OC_DIRT_LV
F SIDEA_DIRT_ALARM_LV
G SIDEA_DIRT_SHADING_SET
53-10
Purpose Adjustment/Setup
Function (Purpose) RSPF dirt detection execution.
Section
Operation/Procedure
1) Press [EXECUTE] key.
Item
SPF SIDEA RSPF front surface dirt detection position (main scan
position 1 to 8)
"-": No dirt, A"*": Dirt
OC OC surface dirt detection position (main scan position
1 to 8)
"-": No dirt, "*": Dirt
55
55-1
Purpose (Do not use this function unless specially
required.)
Function (Purpose) Used to set the specifications of the engine
control operations. (SOFT SW)
Section
Operation/Procedure
55-2
Purpose (Do not use this function unless specially
required.)
Function (Purpose) Used to set the specifications of the scan-
ner control operation. (SOFT SW)
Section
Operation/Procedure
OFF RSPF dirt alarm setting
ON
OFF RSPF front surface optimum scan position detection
setting (When starting)
ON
OFF RSPF front surface optimum scan position detection
setting (After a job)
ON
WEAK RSPF front surface optimum scan position detection
level setting
MIDDLE
STRONG
WEAK OC dirt level setting
MIDDLE
STRONG
WEAK RSPF front surface dirt alarm level setting
MIDDLE
STRONG
OFF RSPF front surface streak delete shading setting
ON
Content
MX-3114N SIMULATION 6 – 96
Operation/Procedure
1) Select an items to be set with scroll key.
2) Enter the set value with 10-key.
3) Press [OK] key. (The set value is saved.)
Content
55-3
Purpose (Do not use this function unless specially
required.)
Function (Purpose) Used to set the specifications of the control-
ler operation. (SOFT SW)
Section
Operation/Procedure
55-10
Purpose Adjustment/Setting
Function (Purpose) Used to set the special stamp text. (Taiwan
only)
Section
Operation/Procedure
1) Select an item to be set (digit, color, type) with the scroll key.
2) Enter the value corresponding to the setting item with 10-key.
3) Press [OK] key.
Item/Display
A 1ST DIGIT First digit (left edge)
B 2ND DIGIT Second digit
C 3RD DIGIT Third digit
D 4TH DIGIT Fourth digit
E 5TH DIGIT Fifth digit
F 6TH DIGIT Sixth digit (right
edge)
G COLOR K Color specification
input
C
M
Y
R
G
B
Setting Default
range value
OFF 0 - 1 0 1
(OFF)
ON 1
OFF 0 - 1 0 1
(ON)
ON 1
OFF 0 - 1 0 1
(ON)
ON 1
Low 0 - 2 0 1
(MIDDLE)
Medium 1
High 2
Low 0 - 2 0 1
(MIDDLE)
Medium 1
High 2
Low 0 - 2 0 1
(MIDDLE)
Medium 1
High 2
OFF 0 - 1 0 1
(ON)
ON 1
Setting Default
Content
range value
1 - 90 1
32 [blank:
20H]
65 - 90
[Alphabet:
41H("A) -
5AH("Z")]
48 - 57
[Numeral:
30H("0") -
39H("9")]
0 0
1
2
3
4
5
6