Rehau NEA SMART 2.0 Service Manual page 5

5.3.3 Analog Input
5.3.4 Digital Inputs
5.3.5 Digital Outputs
5.4 Internet Connection
5.5 Wiring
5.6 Application Examples
5.6.1 Heating system with mix of wireless and wired Room
units (up to eight rooms)
5.6.2 Heating and Cooling system with mix of wireless and
wired Room units and R-Module (up to twelve rooms)
5.6.3 Heating and Cooling system with mix of wireless and
wired Room units and slaves (up to twenty four rooms)
5.6.4 Heating and Cooling system with mix of wireless and
wired Room units and U-Module (for mixed circuit)
6 Installation
6.1 Leaflets
7 System set up
7.1 General remarks to set up procedure
7.1.1 Preparation
7.1.2 Different complexity of systems (class A, B, C)
7.1.3 Flow chart of set up procedure
7.2 Set system bus addresses
7.3 Switch on power supply
7.3.1 Check POWER / FUSE LED's
7.3.2 Check zone bus LED's
7.3.3 Check manifold actuators
7.4 Pairing
7.4.1 General notes
7.4.2 Start pairing procedure on Base
7.4.3 Pairing of NEA SMART 2.0 Room units
7.4.4 Pairing of NEA SMART 2.0 Room probes
7.4.5 Pairing of NEA SMART 2.0 outdoor sensor
7.4.6 Further settings on NEA SMART 2.0 Room units
7.5 Configuration Wizard
7.5.1 Introduction
7.5.2 Preparation
7.5.3 Example for configuration
7.5.4 General settings
7.5.5 Choose system type
7.5.6 Enter system components and functions
7.5.7 Scan system bus components
7.5.8 Define function of system bus components
7.5.9 Input / output assignment of U-Modules for mixed circuit 61
7.5.10 Definition of mixed circuit operating
7.5.11 Links between mixed circuits and manifolds
7.5.12 Input / output assignment of U-Modules for dehumidifiers 62
7.5.13 Overview of Base units
7.5.14 Definition of room operating modes
7.5.15 Definition of outputs of the Base
7.5.16 Definition of inputs of the Base
7.5.17 End of wizard, enable or disable automatic mode
7.6 Installer main menu
7.6.1 Timer programs
39 7.6.2 Room set up
40 7.6.3 System data
41 7.6.4 Diagnosis / probe calibration
42 7.6.5 Settings (Parameters)
43 7.7 Reset functions
44 7.7.1 Delete pairing of all channels (RZs) on one room unit
7.7.2 Delete pairing of outside temperature probe
44 7.7.3 Reset Controller to initial state
7.7.4 Reset Room Unit
45 7.7.5 Reset WIFI Key to default setting
46 8 Operating of NEA SMART 2.0 SYSTEM
8.1 Operating by NEA SMART 2.0 Room units
47 8.1.1 Display information
8.1.2 Order of the displayed information
48
8.1.3 Setting the Setpoint of room temperature
48 8.1.4 Operating status
8.2 Operating by web pages
49 8.2.1 Connect a device
49 8.2.2 User area
49 8.2.3 Installer area
49 8.3 Operating by REHAU SMART 2.0 App
49 8.3.1 Installation of the App
50 8.3.2 Setting up the App
50 8.3.3 Getting to know the App
51 8.3.4 First steps in the App
51 8.3.5 Smart function Geofencing
51 8.3.6 Account Management
52 8.4 FAQ's and troubleshooting
52 8.4.1 Problems and potential causes
52 8.4.2 Error-codes on NEA SMART 2.0 Room Units
53 8.4.3 Change batteries of Room Units and Probes
54
9 Parameter
54
54 9.1 Heating general
56 9.1.1 Heating circuits
56 9.1.2 Heating circuits, boost function
56 9.2 Heating circuits, boost function
57 9.2.1 Cooling circuits
58 9.3 Mixing circuit control
58 9.4 Room temperature control
59 9.5 Device control
60 9.5.1 Heater control
60 9.5.2 Chiller control
9.5.3 Dehumidifier control
62 9.5.4 Pump control
62 9.5.5 Valve control
10 Data
63
63 10.1 Electrical termination
65 10.2 Factory settings
65 10.2.1 Basis
66 10.2.2 R-Modul
66 10.2.3 U-Module (Defined as Mixed circuit)
67 10.2.4 U-Module (Defined as Dehumidifier)
68
70
70
70
71
71
71
71
71
71
72
73
73
75
75
76
76
76
76
80
85
85
85
86
89
90
90
91
91
91
92
93
93
94
95
96
97
97
98
99
99
99
100
101
101
102
102
102
102
103
103
104
5