Table 7. Binary Values - Trane Tracer UC600 Installation Manual

O O b b j j e e c c t t a a n n d d D D i i a a g g n n o o s s t t i i c c D D a a t t a a P P o o i i n n t t s s
Table 6. Binary Outputs (continued)
Object
Object Name
Identifi-
er
Supply Fan 1 Start
BO100
Stop Command
Supply Fan 2 Start
BO101
Stop Command
Supply Fan 3 Start
BO102
Stop Command
Supply Fan 4 Start
BO103
Stop Command
Supply Fan 5 Start
BO104
Stop Command
Supply Fan 6 Start
BO105
Stop Command
Compressor 1 VFD
BO108
Alarm Reset
Compressor 1 E-Stop
BO109
Shutdown Command
Cooling Tower Pump
BO125
Request
Unit Alarm Output
BO126
Command

Table 7. Binary Values

Object
Object Name
Identifi-
er
Supply Fan Failure
BV2
Reset
Diagnostic: Space
BV11 Temperature Source
Failure
Diagnostic: Duct
BV15
Static Pressure Failure
Cooling Safeties OK
BV18
Diagnostic: Discharge
BV19 Air Low Temperature
Lockout
BV21 Heat Cool Mode Active
Compressor 1 Lockout
BV29
BAS
Compressor 2 Lockout
BV30
BAS
Compressor 3 Lockout
BV31
BAS
Compressor 4 Lockout
BV32
BAS
BV36 Alarm Reset
Diagnostic: Auto Reset
BV37
Diagnostic: Discharge
BV42 Air Temperature
Source Failure
Mixed Air Low Limit
BV52
Active
24
Units of Minimum
Measure Maximum
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
Units of Minimum
Measure Maximum
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
When the Object
Exists
Normally Open Contacts Used Only
Units with at least 1
Open = Stop Closed = Run
Fan
Normally Closed Contacts not used
Normally Open Contacts Used Only
Units with at least 2
Open = Stop Closed = Run
Fan
Normally Closed Contacts not used
Normally Open Contacts Used Only
Units with at least 3
Open = Stop Closed = Run
Fan
Normally Closed Contacts not used
Normally Open Contacts Used Only
Units with at least 4
Open = Stop Closed = Run
Fan
Normally Closed Contacts not used
Normally Open Contacts Used Only
Units with at least 5
Open = Stop Closed = Run
Fan
Normally Closed Contacts not used
Normally Open Contacts Used Only
Units with at least 6
Open = Stop Closed = Run
Fan
Normally Closed Contacts not used
Unit where Normally Open Contacts Used Only
compressor 1 is a Open = Normal Closed = Reset
VFD Compressor Normally Closed Contacts not used
Normally Open Contacts Used Only
Unit where
Open = Normal Closed = Emergency
compressor 1 is a
VFD Compressor
Normally Closed Contacts not used
Water Cooled Normally Open Contacts Used Only
Condenser Units Open = Off Closed = Request On
Only Normally Closed Contacts not used
Normally Open Contacts Used Only
Open = No Alarms Closed = Alarm
All Units
Normally Closed Contacts not used
When the Object
Exists
All units
Units with Space
Temperature Option. Non latching Diagnostic, clears
Units with Duct
Non latching Diagnostic, clears
Pressure Sensor
All Units
All Units
Latching Diagnostic. Cleared with
Alarm Reset or Power Cycle.
All Units
Units with at least 1
Compressor
Units with at least 2
Compressors
Units with at least 3
Compressors
Units with at least 4
Compressors
All Units
All Units
All Units
Non latching Diagnostic, clears
Units with Water
Side Economizer
Description
Stop
Present
Description
Open = Normal
Closed = Reset
Open = Normal
Closed = Failure
automatically
Open = Normal
Closed = Failure
automatically
Open = Stop Cooling
Closed = Cooling OK
Open = Normal
Closed = Failure
Open = Heat
Closed = Cool
Open = Available
Closed = Locked Out
Open = Available
Closed = Locked Out
Open = Available
Closed = Locked Out
Open = Available
Closed = Locked Out
Open = Normal
Closed = Reset
Open = Normai
Closed = Alarm
Open = Normal
Closed = Failure
automatically
BAS-SVP042A-EN
Read/
Write
Read Only
Read Only
Read Only
Read Only
Read Only
Read Only
Read Only
Read Only
Read Only
Read Only
Read/
Write
Read Only
Read Only
Read Only
Read Only
Read Only
Read Only
Writeable
Writeable
Writeable
Writeable
Writeable
Read Only
Read Only
Read Only