Page 1: Table Of Contents
Privacy Wall Glass with 1” Flange VIA Glass media:scape Wall Tilt Bracket Kit Glass Tilt Bracket Kit Single Gang Junction Box FCC Statement 3/16”, 5/16” ½”, 5/8”, #32 ®2020 Steelcase Inc. Grand Rapids, MI 49501 U.S.A. Printed in U.S.A. Page 1 of 20...
Page 2: Mounting Selection Guide And Install Notes
RoomWizard device. Notice Leave the protective cover on the RoomWizard until secured in the mount bracket. Steelcase has tested this protective cover so the RoomWizard can survive a 54” drop onto concrete. Table 1 Protective Cover Page 2 of 20...
Page 3: Poe Cable Drops
RoomWizard Mounting Kits © PoE Cable Drops Installation Instructions • PoE Cable drops should be located 52” (1325cm) from the floor. • If running PoE cable without connector, minimum hole size ½” should be Ø (12mm). • If running PoE cable with connector, the minimum hole size 52”...
Page 4: Hard Surfaces (Wood, Drywall, Etc.)
RoomWizard Mounting Kits Hard Surfaces (wood, drywall, etc.) © Installation Instructions 1. Temporarily locate the wall mount bracket onto the wall. The wall mounting bracket should be centered 52” ½ (132cm) from the floor. Ensuring it’s level, mark (1) ” or 5/8”...
Page 5 Ensure the wall mount bracket is level before final tightening. 6. Plug the PoE cable into the back of the RoomWizard. 7. Attach the RoomWizard into the mount bracket. 8. Peel or cut the large tabs on protective cover, then slide to remove the protective cover.
Page 6: Standard Glass
The PoE cable cover should extend no more than a ½” (12mm) into the mount. 5. Plug the PoE cable into the back of the RoomWizard. 6. Attach the RoomWizard to the glass mount bracket. 7. Peel or cut the tabs on protective cover and slide to remove the protective cover.
Page 7: Privacy Wall Glass Without 1" Flange
Privacy Wall (without 1” flange) RoomWizard Mounting Kits © Installation Instructions 1. Temporarily locate the glass mount bracket onto extrusion and mark (1) ½” or 5/8” hole for PoE cable. The glass mounting bracket should be centered 52” (132cm) from the floor 2.
Page 8 FROM ADHESIVE STRIPS pressure for at least 15 seconds. 5. Plug the PoE cable into the back of the RoomWizard. 6. Attach the RoomWizard to the glass mount bracket. 7. Peel or cut the tabs on protective cover, then slide to remove the protective cover.
Page 9: Privacy Wall Glass With 1" Flange
Privacy Wall (with 1” flange) RoomWizard Mounting Kits © Installation Instructions 1. Temporarily locate the glass mount bracket onto extrusion and mark (1) ½” or 5/8” hole for PoE cable. The glass mounting bracket should be centered 52” (132cm) from the floor 2.
Page 10 Hold even pressure for at least 15 seconds. FROM ADHESIVE STRIPS 9. Plug the PoE cable into the back of the RoomWizard. 10. Attach the RoomWizard to the glass mount bracket. 11. Peel or cut tabs on protective cover, then slide to remove the protective cover.
Page 11: Via Glass
RoomWizard Mounting Kits VIA Glass © Installation Instructions 1. Temporarily locate the glass mount bracket onto extrusion. The glass mounting bracket should be centered 52” (132cm) from the floor. 2. Thoroughly clean an area at least as large as the mounting bracket using the alcohol wipe provided.
Page 12 15 seconds. 5. Plug the PoE cable into the back of the RoomWizard. 6. Attach the RoomWizard to the glass mount bracket. If possible, push any excess cable back into the wall frame. 7. Peel or cut tabs on the protective cover, then slide to remove the protective cover.
Page 13: Media:scape
#2 Phillips screwdriver, install using the four (4) screws and four (4) washers and four (4) nuts. Ensure wall mount bracket is level before final tightening 5. Plug the PoE cable into the back of the RoomWizard. Page 13 of 20...
Page 14 RoomWizard Mounting Kits © Installation Instructions 6. Attach the RoomWizard to the wall mount bracket. 7. Peel or cut tabs on the protective cover, then slide to remove the protective cover. Peel or cut the tabs on the protective cover...
Page 15: Wall Tilt Bracket Kit
RoomWizard Mounting Kits Wall Tilt Bracket © Installation Instructions 1. Temporarily locate the wall mount bracket onto the wall. The wall mounting bracket should be centered 52” ½ (132cm) from the floor. Ensuring it’s level, mark (1) ” or 5/8” hole for PoE cable and (4) 3/16” (5mm) for wall anchors.
Page 16 Ensuring mount brackets are level, tighten screws. 6. Plug the PoE cable into the RoomWizard. 7. Attach the RoomWizard to the wall mount bracket. 8. Peel or cut the tabs on the protective cover, Screws then slide to remove the protective cover.
Page 17: Glass Tilt Bracket Kit
Glass Tilt Bracket RoomWizard Mounting Kits © Installation Instructions 1. Temporarily locate the glass tilt bracket onto glass wall. GLASS TILT BRACKET The glass tilt bracket should be centered 52” (132cm) from the floor to the center of the PoE cable hole.
Page 18 Ensuring the wall mount bracket is level, tighten screws with Phillips screwdriver. 6. Plug the PoE cable into the back of the RoomWizard. SCREWS 7. Attach the RoomWizard to the wall mount bracket.
Page 19: Single Gang Junction Box
(4) #6-32 nuts. 4. Plug the PoE cable into the back of the RoomWizard. 5. Attach RoomWizard to the wall mount bracket. 6. Peel or cut tabs on the protective cover, then slide to remove the protective cover. Peel or cut the tabs on...
Page 20: Fcc Statement
2. This device must accept any interference received, including interference that may cause undesired operation. FCC Warning Changes or modifications to this product not authorized by Steelcase Inc. could void the electromagnetic compatibility (EMC) and wireless compliance and negate the user’s authority to operate the product.

Steelcase RoomWizard Installation Instructions Manual

Quick Links

Table of Contents

Related Manuals for Steelcase RoomWizard

Summary of Contents for Steelcase RoomWizard

Table of Contents