Table of Contents
Advertisement
From the Measurement Preparation section
When performing measurement in analyzer mode
<Inputting the RGB Emission Characteristic for
Analyzer mode> Page 59
Can be set to all the memory channels.
7
8
1
2
4
6
5
When the optional 4-point expansion board CA-B04 is used
User calibration is performed independently for probe
connectors ([P1] to [P5]) for each memory channel.
1 Press the
key to display the menu selection screen.
2 Press the
key to open the PROBE selection screen.
3 Press the
key until the desired probe connector
no. appears.
4 Press the
key to confirm the selection.
Memory channel
CH01 EXT
[
1. Press the MODE key to select analyzer mode.
2. Press the CH
and
desired memory channel.
3. Press the
key.
4. Input the emission characteristic of R.
1 Place the measuring probe against the display, which is now emitting
monochrome light of R.
2 Press the
key.
In the LCD display section, the " * " mark will appear on the left of "R".
5. Input the emission characteristic of G.
1 Place the measuring probe against the display, which is now emitting
monochrome light of G.
2 Press the
key.
In the LCD display section, the " * " mark will appear on the left of "G".
6. Input the emission characteristic of B.
1 Place the measuring probe against the display, which is now emitting
monochrome light of B.
2 Press the
key.
In the LCD display section, the " * " mark will appear on the left of "B".
7. Input the emission characteristic of W.
1 Place the measuring probe against the display, which is now emitting
monochrome light of W.
2 Press the
key.
In the LCD display section, the " * " mark will appear on the left of "W".
8. Press the
key.
The RGB emission characteristic for the display and
target color will be set.
To change the target color after user calibration:
*1 <Setting/Changing the Target Color> Page 117
To set an ID name:
*2 <Setting an ID Name> Page 119
To use the analog display function:
*3 <Setting the Analog Display Range> Page 119
To the Measurement section
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
3
4,5,6,7
Probe connector no.
Ad P1
]
keys to select the
CH01
ALZ
P1
W
R
G
B
CH01
ALZ
P1
W
R
G
B
CH01
ALZ
P1
W
R
G
B
CH01
ALZ
P1
W
R
G
B
CH01 EXT
Ad P1
[
]
Page 75
119
*2
<Setting an ID Name> Page 67
Can be set to all the memory channels.
1
4
1. Press the CH
and
desired memory channel.
2. Press the
key.
3. Press the
key to open the ID name input
screen.
4. Enter the desired ID name.
Ten-key (
to
,
) ... Used to enter values.
Key .. Can be used to enter an alphabet,
hyphen (-) and space. Pressing this
key again will restore the original
function of the ten-key.
Key .. Moves the cursor to the right each
time this key is pressed.
5. Press the
key.
*3
<Setting the Analog Display Range> Page 69
1
4
1. Press the MODE key to select the measurement
mode for which you want to set the range.
2. Press the
key.
3. Press the
key to open the RANGE setting
screen.
RANGE x,y
4. Enter the desired range value.
Ten-key (
to
,
) ... Used to enter values.
Key .. Moves the cursor to the right each
time this key is pressed.
For analyzer mode (G reference)
RANGE G
For analyzer mode (R reference)
RANGE R
5. Press the
key.
2
3
5
keys to select the
Memory channel
CH01 EXT
Ad P1
[
]
MENU : SELECT
PUSH SPACE KEY
CH01 EXT
Ad P1
[EXT D-1.50]
_
Cursor ID name
2
3
5
MENU : SELECT
PUSH SPACE KEY
Lv
(%) 10
10
_
B/G,R/G
(%) 10
10
_
B/G,R/G
(%) 10
10
_
Advertisement
Table of Contents
