Simatic Rf600 - Siemens SIMATIC RF600 System Manual

System diagnostics
9.2 XML/PLC error messages
"ER" XML/ PLC block
LED LED (hex)
(hex)
-- 0x65 0xE6FE05
-- 0x66 0xE6FE06
2 Hz 0xE1 0xE6FE81
2 Hz 0xE2 0xE6FE82
2 Hz 0xE3 0xE6FE83
2 Hz 0xE4 0xE6FE84
2 Hz 0xE5 0xE6FE85
2 Hz 0xE6 0xE6FE86
2 Hz 0xE7 0xE6FE87
2 Hz 0xE8 0xE6FE88
2 Hz 0xE9 0xE6FE89
2 Hz 0xEA 0xE6FE8A
2 Hz 0xEB 0xE6FE8B
2 Hz 0x71 0xE7FE01
-- 0x72 0xE7FE02
-- 0x73 0xE7FE03
-- 0x74 0xE7FE04
-- 0x75 0xE7FE05
-- 0x76 0xE7FE06
-- 0x77 0xE7FE07
-- 0x78 0xE7FE08
478
Error description
An error has occurred that makes a Reset_Reader ("WRITE-CONFIG" with "Config = 3")
necessary.
Possible causes / action to be taken:
The "WRITE-CONFIG" command is incorrect.
•
After eliminating the error, execute an "INIT".
•
Check the "IID_HW_CONNECT" parameter.
•
The reset timer has expired.
A parameter is missing.
The parameter has an invalid format.
The parameter type is invalid.
Unknown parameter.
The command or the frame has an invalid format.
The inventory command failed.
Read access to the transponder failed.
Write access to the transponder failed.
Writing the EPC-ID on the transponder failed.
Enabling write protection on the transponder failed.
The "Kill" command failed.
In this status, only the "Reset_Reader" command ("WRITE-CONFIG") is permitted.
The "CMD" command code is not permitted.
The "LEN_DATA" parameter of the command is too long and does not match the global
data reserved within the send data buffer (TXBUF).
The receive data buffer (RXBUF) or the send data buffer (TXBUF) is too small, the buffer
created at TXBUF/RXBUF does not have the correct data types or the parameter
"LEN_DATA" as a negative value.
Possible cause / action to be taken:
Check whether the buffers TXBUF/RXBUF are at least as large as specified in
•
LEN_DATA.
With S7-1200/1500:
•
– In the Ident profile, only an "Array of Byte" may be created for TXBUF and RXBUF.
– In the "Reader_Status" block, only an "Array of Byte" or the corresponding data
types ("IID_TAG_STATUS_XX_XXX" or "IID_READER_STATUS_XX_XXX") may be
created
Error message that informs you that only an "INIT" command is permitted as the next com-
mand. All other commands are rejected.
Wrong index
Permitted index is in the ranges "101 ... 108" and "-20401 ... -20418".
The reader or communications module does not respond to "INIT" ("INIT_ACTIVE" is ex-
pected in the cyclic status message).
The next steps:
Check the address parameter "LADDR".
•
Timeout during "INIT" (60 seconds according to "TC3WG9")
System Manual, 06/2019, J31069-D0171-U001-A22-7618

SIMATIC RF600