Sony VENICE MPC-3610 Operating Instructions Manual page 82

000 82
4. Network: Network Setup and Operations
OSS (Open Source Software) Information screen
Select OSS Information in the Global Menu to
display the open source software information.
Playback screen
You can play clips on the playback screen.
Information about the playback clip is also
displayed in the status display area on the screen.
ˎ Function display (page 74) ˎ
F Rev, Play/Pause, F Fwd, Prev, Stop/Clips, Next
ˎ Playback status display (page 74) ˎ
Time data, clip number, frame rate/playback clip
picture size (AXS only), special recording mode,
audio level meter, playback clip format (codec),
icon (protection, sub clip), clip name, playback
media, and playback status.
HOME button
Press the HOME button to return to the Camera
screen.
When the camera is in playback mode, pressing
the HOME button returns to the camera shooting
status even when the playback screen is displayed
on the web remote control screen.
CLIPS button
Press the CLIPS button to return to the playback
screen. (The unit switches to the clip list screen
(page 73).)
Recording
Press the Rec button on the Camera Control
screen to start recording and to display the REC
lamp in red. Click again to stop recording.
The Rec button is enabled when the REC ACTIVE
lamp below and to the right of the Rec button is
green.
To lock the Rec button
Slide the Lock slider below the Rec button to the
right to disable the Rec button operation.
Playing
Press the CLIPS button on the Camera screen to
return to the playback screen in playback state.
(The sub display on the unit displays the clip list
screen (page 73).)
Select the clip you want to play on the playback
screen, and use the playback controls to play the
clip.
To switch between playback media
The media select button is displayed when the
unit is in playback state. If both SxS and AXS media
are playable, the media select button is enabled.
Press the button to switch the playback media.
Configuring Shooting Settings
You can configure and operate the same items
that are displayed on the Home screen of the sub
display of the unit on the Camera screen.
[Note]
Step Edit operation for Shutter is not supported.
The operation is the same as on the Home screen
of the sub display.
"Operations on the Home Screen of the Sub Display" (page 33)
Controlling the Lens
You can check the status of E mount lens settings
(zoom, focus, iris) on the Lens screen, and also
control the zoom, focus, and iris using sliders if the
attached lens is controllable.
PL mount Cooke lens communication control is
supported on the Lens screen.
Also, 12-pin lens communication control is
supported on the Lens screen.
[Note]
The sliders are grayed out and cannot be operated when
an RM-B170 or other remote control unit is connected and
Technical > System Configuration > RM/RCP Paint Control
(page 68) is set to On in the full menu. The focus and
zoom sliders are grayed out when remote control of focus
and zoom, respectively, are enabled.
Configuring/Operating Assignable
Buttons
Assignable buttons 1 to 4 and viewfinder
assignable buttons A to C are displayed on the
Camera Control screen.
Press assignable buttons 1 to 4 and DVF-EL200
assignable buttons A to C to toggle the assigned
functions between on/off (enable/disable) or to
activate the assigned functions in the same way as
assignable buttons on the unit.
Select the function name of an assignable button
to display selection options in a pull-down. Select
an option to change the function assigned to the
assignable button.
"Functions that can be Assigned to Assignable Buttons 1 to 4"
(page 40)
"Functions that can be Assigned to Viewfinder (DVF-EL200)
Assignable Buttons A to C" (page 42)
[Note]
Functions assigned to assignable switches that are enabled
only while a button is pressed or are enabled by a long press
cannot be operated from the assignable buttons of the web
remote control. These comprise the following functions.
– Press & Hold for SDI Log
– Press & Hold for Monitor Log
– Press & Hold for VF Log
– Iris Open (1/16 stop)
– Iris Close (1/16 stop)
Locking the Web Remote Control
Screen
You can disable web remote control screen
operation by sliding the Lock slider to the right on
the top right of the web remote control screen.