Sony VENICE MPC-3610 Operating Instructions Manual page 14

000 14
1. Overview: Location and Function of Parts
18.
SDI output REC trigger indicator
Displays the SDI output REC trigger status.
State
Technical > System Configuration > SDI Rec Remote
Trigger in the full menu
Off
HD SDI Remote I/F
Parallel Rec
19.
Network connection status indicator
Displays the network connection status (LAN
or Wi-Fi).
State
Disconnected or other error (valid
network connection settings)
Connected (valid network connection
settings)
Network connection function not
used
20.
Audio level meter indicators
Displays the levels of audio channels 1 and 2
while recording.
21.
Recording media state/remaining capacity
indicator for each media slot
Displays the state and remaining capacity of
the media in SxS memory card slots A/B and
AXS memory card slots A/B.
A mark on the left of "AXS" or "SxS" indicates
the recording target media.
An indicator on the upper right of the slot
A/B icon on the right of "AXS" or "SxS" indicates
the playback target media (green indicator
indicates media is being played).
Recording command
superimposed on the
SDI output
–
Stop command
Rec command
Stop command
Rec command
A icon is displayed for media if a condition
occurs that could impact recording.
22.
High Key/Low Key indicator (Monitor output)
Displayed when the Monitor output is High
Display
Key (screen for checking blown-out highlights)
Flashing
or Low Key (screen for checking blocked-out
shadows) (displayed for Monitor Out output).
On
23.
Recording media format (codec) indicator
Blank
Displays the format of the recording on an AXS
memory card or an SxS memory card.
24.
Recording status indicator
Displays the following recording operation
states of the unit.
Display Description
Recording

Rec
Recording standby

Stby
Picture cache recording
 Cache
standby
25.
Clip name display
Displays the first 8 characters of the name of
the next clip to be recorded in recording
standby mode.
Displays the first 8 characters of the name of
the clip currently being recorded when
recording.
Display
26.
Time data display
Displays the duration or timecode, depending
on the TC/Media category > TC Display setting
in the menu (page 44).
(Blank)
27.
Iris position indicator
Top: SDI
Displays the iris position (only when a lens that
Bottom: Stop
is compatible with the iris setting display
Top: SDI
function is attached).
Bottom: REC
The iris position indicator displays in 1/3 stop
Top: SDI-P
increments when using an E mount lens.
Bottom: Stop
[Note]
Top: SDI-P
The F-stop value is displayed instead of the T-stop value
Bottom: REC
if the T-stop value cannot be obtained.
28.
Focus position indicator
Displays the focus position (only when a lens
that is compatible with the focus setting
display function is attached).
29.
Zoom position indicator
Displays the focal length of the zoom
(displayed only when a lens that supports the
zoom setting indicator is attached).
30.
High Key/Low Key indicator (viewfinder
output)
Displayed when the viewfinder output is High
Key (screen for checking blown-out highlights)
or Low Key (screen for checking blocked-out
shadows) (displayed for viewfinder output).
31.
Simultaneous recording status indicator
Displays the sub clip recording format in 1-slot
simultaneous recording mode (page 84).
32.
SxS Sub LUT indicator
Displays the LUT setting to register for a sub
clip in SxS 1-slot simultaneous recording
mode.
33.
SxS LUT indicator
Displays the LUT setting for SxS recording.
34.
Base ISO indicator
Displays the configured native sensitivity.
35.
Effective picture size indicator
Displays the effective picture size and whether
anamorphic de-squeeze conversion is applied,
set using Project category > Imager Mode in
the menu. In Surround View mode, a "Sur.V"
icon is displayed below the anamorphic
conversion factor icon (page 44).
Menu display and settings on the viewfinder
screen
When a DVF-EL200 is attached to the unit, press
and hold the Menu button on the DVF-EL200 to
display the Monitoring > VF Display (page 66)
and VF Function (page 66) setup menus on the
viewfinder screen. This allows you to configure
these functions while viewing the viewfinder
screen.