Danfoss VLT Micro Drive FC 51 Programming Manual page 53

Parameter Lists
VLT
6-0* Analog I/O Mode [1] 4-20 mA
6-00 Live Zero Timeout Time [2] Digital Output
1-99 s *10 s 6-91 Terminal 42 Analog Output
6-01 Live Zero TimeoutFunction *[0] No operation
*[0] Off [10] Output Frequency
[1] Freeze output [11] Reference
[2] Stop [12] Feedback
[3] Jogging [13] Motor Current
[4] Max speed [16] Power
[5] Stop and trip [20] Bus Reference
6-1* Analog Input 1 6-92 Terminal 42 Digital Output
6-10 Terminal 53 Low Voltage See par. 5-40
5 5
0.00-9.99 V *0.07 V *[0] No Operation
6-11 Terminal 53 High Voltage [80] SL Digital Output A
0.01-10.00 V *10.00 V 6-93 Terminal 42 Output Min
6-12 Terminal 53 Low Current Scale
0.00-19.99 mA *0.14 mA 0.00-200.0%
6-13 Terminal 53 High Current *0.00%
0.01-20.00 mA *20.00 mA 6-94 Terminal 42 Output Max
6-14 Term. 53 Low Ref./Feedb. Scale
Value 0.00-200.0% *100.0%
-4999-4999 *0.000 7-** Controllers
6-15 Term. 53 High Ref./Feedb. 7-2* Process Ctrl. Feedb
Value 7-20 Process CL Feedback 1
-4999-4999 *50.000 Resource
6-16 Terminal 53 Filter Time *[0] NoFunction
Constant [1] Analog Input 53
0.01-10.00 s *0.01 s [2] Analog input 60
6-19 Terminal 53 mode [8] PulseInput33
*[0] Voltage mode [11] LocalBusRef
[1] Current mode 7-3* Process PI
6-2* Analog Input 2 Ctrl. 7-30 Process PI Normal/
6-22 Terminal 60 Low Current Inverse Ctrl
0.00-19.99 mA *0.14 mA *[0] Normal
6-23 Terminal 60 High Current [1] Inverse
0.01-20.00 mA *20.00 mA 7-31 Process PI Anti Windup
6-24 Term. 60 Low Ref./Feedb. [0] Disable
Value *[1] Enable
-4999-4999 *0.000 7-32 Process PI Start Speed
6-25 Term. 60 High Ref./Feedb. 0.0-200.0 Hz *0.0 Hz
Value 7-33 Process PI Proportional Gain
-4999-4999 *50.00 0.00-10.00 *0.01
6-26 Terminal 60 Filter Time 7-34 Process PI Integral Time
Constant 0.10-9999 s *9999 s
0.01-10.00 s *0.01 s 7-38 Process PI Feed Forward
6-8* LCP potentiometer Factor
6-80 LCP LCP Potmeter Enable 0-400% *0%
[0] Disabled 7-39 On Reference Bandwidth
[1] * Enable 0-200% *5%
6-81 LCP potm. Low Reference 8-** Comm. and Options
-4999-4999 *0.000 8-0* General Settings
6-82 LCP potm. High Reference 8-01 Control Site
-4999-4999 *50.00 *[0] Digital and ControlWord
6-9* Analog Output xx [1] Digital only
6-90 Terminal 42 Mode [2] ControlWord only
*[0] 0-20 mA
Table 5.3
52 MG02C602 - VLT
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-12769-Danfoss-132F0026-VFD-Micro-Drive-440V-5HP.aspx
®
Micro Drive FC 51 Programming Guide
8-02 Control Word Source [13] [1613] Frequency
[0] None [14] [1614] Motor Current
*[1] FC RS485 [15] [1615] Frequency [%]
8-03 Control Word Timeout Time [16] [1618] Motor Thermal
0.1-6500 s *1.0 s [17] [1630] DC Link Voltage
8-04 Control Word Timeout [18] [1634] Heatsink Temp.
Function [19] [1635] Inverter Thermal
*[0] Off [20] [1638] SL Controller State
[1] Freeze Output [21] [1650] External Reference
[2] Stop [22] [1651] Pulse Reference
[3] Jogging [23] [1652] Feedback [Unit]
[4] Max. Speed [24] [1660] Digital Input
[5] Stop and trip 18,19,27,33
8-06 Reset Control Word Timeout [25] [1661] Digtial Input 29
*[0] No Function [26] [1662] Analog Input 53(V)
[1] Do reset [27] [1663] Analog Input 53(mA)
8-3* FC Port Settings [28] [1664] Analog Input 60
8-30 Protocol [29] [1665] Analog Output 42
*[0] FC [mA]
[2] Modbus [30] [1668] Freq. Input 33 [Hz]
8-31 Address [31] [1671] Relay Output [bin]
1-247 *1 [32] [1672] Counter A
8-32 FC Port Baud Rate [33] [1673] Counter[34] [1690]
[0] 2400 Baud Alarm Word
[1] 4800 Baud [34] [1690] Alarm Word
*[2] 9600 Baud For choosing FC [35] [1692] Warning Word
bus in 8-30 [36] [1694] Ext. Status Word
* [3] 19200 Baud For choosing 8-5* Digital/Bus
FC bus in 8-30 8-50 Coasting Select
*[4] 38400 Baud [0] DigitalInput
8-33 FC Port Parity [1] Bus
*[0] Even Parity, 1 Stop Bit [2] LogicAnd
[1] Odd Parity, 1 Stop Bit *[3] LogicOr
[2] No Parity, 1 Stop Bit 8-51 Quick Stop Select
[3] No Parity, 2 Stop Bits See par. 8-50 * [3] LogicOr
8-35 Minimum Response Delay 8-52 DC Brake Select
0.001-0.5 *0.010 s See par. 8-50 * [3] LogicOr
8-36 Max Response Delay 8-53 Start Select
0.100-10.00 s *5.000 s See par. 8-50 * [3] LogicOr
8-4* FC MC protocol set 8-54 Reversing Select
8-43 FC Port PCD Read Configu- See par. 8-50 * [3] LogicOr
ration 8-55 Set-up Select
*[0] None Expressionlimit See par. 8-50 * [3] LogicOr
[1] [1500] Operation Hours 8-56 Preset Reference Select
[2] [1501] Running Hours See par. 8-50 * [3] LogicOr
[3] [1502] kWh Counter 8-8X Bus communication
[4] [1600] Control Word Diagnostics
[5] [1601] Reference [Unit] 8-80 Bus Message Count
[6] [1602] Reference % 0-0 N/A *0 N/A
[7] [1603] Status Word 8-81 Bus Error Count
[8] [1605] Main Actual Value [%] 0-0 N/A *0 N/A
[9] [1609] Custom Readout 8-82 Slave Messages Rcvd
[10] [1610] Power [kW] 0-0 N/A *0 N/A
[11] [1611] Power [hp] 8-83 Slave Error Count
[12] [1612] Motor Voltage 0-0 N/A *0 N/A
®
is a registered Danfoss trademark