Figure 3-18A. 5882Euh Wireless Transceiver; Figure 3-18B. 5882Eu Wireless Transceiver - Honeywell ADEMCO VISTA-120 Installation And Setup Manual

VISTA-120 Installation and Setup Guide
ANTENNAE
(INSERT IN
RIGHT-HAND
TERMINALS)
MOUNTING
HOLES
(4)
R
Y
G
RF ACTIVITY
DIP
LED
SWITCH
TO RELEASE
CIRCUIT BOARD,
REMOVE SCREWS (2)
POSITION 7: ON SELECTS "QUIET" MODE WHERE THE 5882EUH ONLY SENDS
SIGNALS UPON ALARMS OR IF IT RECEIVES A SIGNAL FROM A 5839H KEYPAD.
USE QUIET MODE FOR WESTERN EUROPEAN ETSI-300-200 COMPLIANCE.
OFF SELECTS NORMAL MODE. USE OFF POSITION
IF 5839H IS PLUGGED INTO AN EXTERNAL POWER SOURCE OR IF A
5840H SIREN IS BEING USED.

Figure 3-18a. 5882EUH Wireless Transceiver

ANTENNAE
(INSERT IN
RIGHT-HAND
TERMINALS)
MOUNTING
HOLES
(4)
3 4
1 2
DIP
SWITCH
RF
ACTIVITY
LED
ON
1 2 3 4 5 6 7 8
NOT USED NOT USED
5882EU ADDRESS SETTINGS
SWITCH
(" " means "OFF")
POSITION
0 1 2 3 4 5 6 7
5 ON ON ON ON
4 ON ON ON ON
3 ON ON ON ON
5882eu_us

Figure 3-18b. 5882EU Wireless Transceiver

5839EU(H)/5882EU(H) Notes
•
5882EU(H) cover must be removed before enrolling
5839EU(H) keypad into receiver.
•
Each 5839EU(H) can be enrolled in only one
5882EU(H) (do not assign a given 5839EU(H) to
more than one transceiver).
Take note of the address you select for the
wireless receiver as this address must be
enabled in the system's Device Programming
mode.
3-10
TO CONTROL'S
YELLOW REMOTE KEYPAD
CONNECTION
RED
POINTS.
BLACK
USE MAX 67M OF
GREEN
0.8MM WIRE OR
168M OF WIRE.
WIRING
OPENING
CPU FAIL LED
TAMPER
SWITCH
DIAGNOSTIC
LEDS
COVER
ON
LOCKING
SCREW
1 2 3 4 5 6 7 8
NOT USED
POSITION 7
NOT USED
NOT USED
SWITCH
5882EUH ADDRESS SETTINGS
POSITION (" " means "OFF")
0 1 2
3 4 5
5
ON ON ON
4
ON ON ON
3
ON ON ON
5882EUH-US-001-V0
CPU WIRING
FAIL OPENING
LED
TO CONTROL'S
YELLOW
REMOTE KEYPAD
RED
CONNECTION
POINTS.
BLACK
USE MAX 67M OF
GREEN
0.8MM WIRE OR
168M OF WIRE.
KNOCKOUT
AREA FOR
SURFACE WIRING
PLUG
AND
SOCKET
REED
TAMPER
7 8
5 6
SWITCH
TO RELEASE CIRCUIT BOARD,
REMOVE SCREWS (2)
POSITION 7: ON SELECTS "QUIET" MODE WHERE THE 5882EU
ONLY SENDS SIGNALS UPON ALARMS OR IT RECEIVES A
SIGNAL FROM A 5839EU KEYPAD.
OFF SELECTS NON-ADDRESSABLE MODE FOR USE WITH THE
VISTA-25, WHERE THE SETTINGS OF POSITIONS
3-5 MUST BE OFF.
POSITION 6: ON SELECTS ADDRESSABLE MODE FOR USE
WITH THE 4140XMPT2/VISTA-120, WHEREIN POSITIONS 3-5
SET THE ADDRESS.
OFF SELECTS NON-ADDRESSABLE MODE
FOR USE WITH THE VISTA-25, WHERE THE SETTINGS
OF POSITIONS 3-5 MUST BE OFF.
Installing the 5800TM Module
Installation of this module is necessary only if you are
using 5827BD Wireless Bi-directional keypads.
The 5800TM must be located between 0.3m and 0.6m
from the receiver's antennas. The 5800TM must not be
installed within the control cabinet. Mount the unit
using its accompanying mounting bracket.
1. Connect the 5800TM to the control panel's keypad
connection terminals, using the supplied connector
with flying leads, as follows:
WIRE
RED (+12VDC)
BLACK (Ground)
GREEN (Data to Control)
7
6
YELLOW (Data from Control)
ON
ON
BLUE: Not Used
ON
2. Cut the red jumper for address setting 28; cut the
white jumper for address 29; cut both jumpers for
address 30.
For additional information, refer to the 5800TM's
instructions.
House ID Sniffer Mode
This mode applies only if you are using a wireless
keypad (5827/5827AP/5827BD) in a 5800 series system.
5800 series receivers respond only to keypads set to the
same House ID (01-31) that is programmed into the
control panel. This prevents system interference from
keypads in other nearby systems. Use the House ID
Sniffer Mode to make sure you do not choose a House
ID that is in use in a nearby system. To enter this
mode, proceed as follows:
1. Enter your "Installer Code" + [#] + [2].
2. The receiver will now "sniff" out any House IDs in
the area and display them. Keep the receiver in
this mode for about 2 hours to give a good
indication of the House IDs being used. Use a
House ID that is not displayed.
3. To exit the Sniffer Mode, simply enter your
Installer Code + OFF.
5800/5800AP/5800EU/5800H Series Transmitter Setup
5800/5800AP/5800EU/5800H series transmitters have
built-in serial numbers that must be "enrolled" by the
system using the # 93 Menu mode programming, or
input to the control via the downloader
5800/5800AP/5800EU/5800H series transmitters
(except 5827/5827AP described separately) do not have
DIP switches.
TERMINAL ON CONTROL
Terminal 6
Terminal 7
Terminal 8
Terminal 9
This address must be enabled as an alpha
keypad in the control's Device Programming
mode and then assigned to a partition.
Since Sniffer Mode effectively disables
wireless point reception, Sniffer Mode cannot
be entered while any partition is armed.