Danfoss VLT FC 300 Operating Instructions Manual page 103

General Specifications
Mains Supply 6x525-690 V AC, 12-Pulse
FC 302
High/ Normal Load*
Typical Shaft output at 550 V [kW]
Typical Shaft output at 575 V [HP]
Typical Shaft output at 690 V [kW]
Enclosure IP21, IP54 without/ with
options cabinet
Output current
Continuous
(at 550 V) [A]
Intermittent (60 s overload)
(at 550 V) [A]
Continuous
(at 575/690 V) [A]
Intermittent (60 s overload)
(at 575/690 V) [A]
Continuous KVA
(at 550 V) [KVA]
Continuous KVA
(at 575 V) [KVA]
Continuous KVA
(at 690 V) [KVA]
Max. input current
Continuous
(at 550 V ) [A]
Continuous
(at 575 V) [A]
Continuous
(at 690 V) [A]
2
Max. cable size, motor [mm
(AWG 2) )]
2
Max. cable size,mains F12 [mm
2)
(AWG )]
Max. cable size,mains F13 [mm 2
2)
(AWG )]
Max. cable size, brake [mm 2
(AWG 2) )
1
Max. external mains fuses [A]
Estimated power loss
4)
at 600 V [W]
Estimated power loss
at 690 V [W] 4)
F3/F4 Max added losses CB or
Disconnect & Contactor
Max panel options losses
Weight,
enclosure IP21, IP54 [kg]
Weight, Rectifier Module [kg]
Weight, Inverter Module [kg]
Efficiency 4)
Output frequency
Heatsink overtemp. trip
Power card ambient trip
* High overload = 160% torque during 60 s, Normal overload = 110% torque during 60 s
1) For type of fuse see section Fuses.
2) American Wire Gauge.
3) Measured using 5 m screened motor cables at rated load and rated frequency.
4) The typical power loss is at nominal load conditions and expected to be within ±15% (tolerence relates to
variety in voltage and cable conditions).
Values are based on a typical motor efficiency. Motors with lower efficiency will also add to the power loss in the
frequency converter and opposite.
If the switching frequency is increased compared to the default setting, the power losses may rise significantly.
LCP and typical control card power consumptions are included. Further options and customer load may add up to
30 W to the losses. (Though typical only 4 W extra for a fully loaded control card, or options for slot A or slot B,
each).
Although measurements are made with state of the art equipment, some measurement inaccuracy must be
allowed for (±5%).
VLT ® Automation Drive FC 300 12-Pulse
Operating Instructions High Power
P900
HO NO HO
750 850 850
1050 1150 1150
900 1000 1000
F12/F13
988 1108 1108
1482 1219 1662
945 1060 1060
1418 1166 1590
941 1056 1056
941 1056 1056
1129 1267 1267
962 1079 1079
920 1032 1032
920 1032 1032
1600
13755 15592 15107
14457 16375 15899
556 665 634
1246/ 1541 1246/ 1541
102
®
MG34Q202 - VLT is a registered Danfoss trademark
P1M0 P1M2
NO HO
1000 1000
1350 1350
1200 1200
F12/F13 F12/F13
1317 1317
1449 1976
1260 1260
1386 1890
1255 1255
1255 1255
1506 1506
1282 1282
1227 1227
1227 1227
12x150
(12x300 mcm)
8x240
(8x500 mcm)
8x400
(8x900 mcm)
6x185
(6x350 mcm)
2000
18281 18181
19207 19105
863 861
400
1280/1575
136
0.98
0-500 Hz
85° C
75° C
P1M4
NO HO NO
1100 1100 1250
1550 1550 1700
1400 1400 1600
F14
1479 1479 1652
1627 2218.5 1817.2
1415 1415 1580
1557 2122 1738
1409 1409 1574
1409 1409 1574
1691 1348 1505
1440 1440 1608
1378 1378 1538
1378 1378 1538
2500
20825 18843 21464
21857 19191 21831
1044 1016 1267
3077/3372
136
103
5 5