Danfoss VLT FC 101 Quick Manual page 33

Quick Guide
1 1
[5] Drive running
[6] Running / no warning
[7] Run in range/no warning
[8] Run on ref/no warning
[9] Alarm
[10] Alarm or warning
[12] Out of current range
[13] Below current, low
[14] Above current, high
[21] Thermal warning
[22] Ready, no thermal warning
[23] Remote, ready, no thermal
warning[24] Ready, Voltage OK
[25] Reverse
[26] Bus OK
[35] External Interlock
[45] Bus Control
[60] Comparator 0
[61] Comparator 1
[62] Comparator 2
[63] Comparator 3
[64] Comparator 4
[65] Comparator 5
[70] Logic rule 0
[71] Logic rule 1
[72] Logic rule 2
[73] Logic rule 3
[74] Logic rule 4
[75] Logic rule 5
[80] SL digital output A
[81] SL digital output B
[82] SL digital output C
[83] SL digital output D
[160] No alarm
[161] Running reverse
[165] Local ref. active
[166] Remote ref. active
[167] Start command act.
[168] Drive in hand mode
[169] Drive in auto mode
[193] Sleep Mode
[194] Broken Belt Function
[196] Fire Mode
[198] Drive Bypass
6-93 Terminal 42 Output Min Scale
0.00–200.00%, * 0.00
6-94 Terminal 42 Output Max Scale
0.00–200.00%, * 100.00
6-96 Terminal 42 Output Bus Control
0.00–100.00%, * 0.00
8-** Comm. and Options
8-0* Comm. General Settings
Table 1.29
1-30
VLT HVAC Basic Drive Quick Guide
Parameter Overview
8-01 Control Site
*[0] Digital and ctrl.word
[1] Digital only
[2] Control word only
8-02 Control Source
[0] None
*[1] FC Port
8-03 Control Timeout Time
0.1–6,500.0s, * 1.0
8-04 Control Timeout Function
*[0] Off
[1] Freeze output
[2] Stop
[3] Jogging
[4] Max. speed
[5] Stop and trip
[20] N2 Override Release
8-06 Reset Control Word Timeout
*[0] No function
[1] Do reset
8-3* FC Port Settings
8-30 Protocol
*[0] FC
[2] Modbus RTU
[3] Metasys N2
[4] FLN
[5] BACNet
8-31 Address
1–247, * 1
8-32 FC Port Baud Rate
[0] 2400 Baud
[1] 4,800 Baud
*[2] 9,600 Baud
[3] 19,200 Baud
[4] 38,400 Baud
[5] 57,600 Baud
[6] 76,800 Baud
[7] 115,200 Baud
8-33 FC Port Parity
*[0] Even Parity, 1 Stop Bit
[1] Odd Parity, 1 Stop Bit
[2] No Parity, 1 Stop Bit
[3] No Parity, 2 Stop Bits
8-35 Minimum Response Delay
0.001–0.500s, * 0.010
8-36 Max Response Delay
0.100–10.000s, *5.000
8-37 Max Inter-char delay
0.025–0.025s, * 0.025
8-5* Digital/Bus
8-50 Coasting Select
®
MG18A322 - VLT is a registered Danfoss trademark
[0] Digital input 8-81 Bus Error Count
[1] Bus 0–65536, * 0
[2] Logic AND 8-82 Slave Message Rcvd
*[3] Logic OR 0–65536, * 0
8-51 Quick Stop Select 8-83 Slave Error Count
[0] Digital input 0–65536, * 0
[1] Bus 8-84 Slave Message Sent
[2] Logic AND 0–65536, * 0
*[3] Logic OR 8-85 Slave Timeout Errors
8-52 DC Brake Select 0–65536, * 0
[0] Digital input 8-88 Reset FC port Diagnostics
[1] Bus *[0] Do not reset
[2] Logic AND [1] Reset counter
*[3] Logic OR 8-9* Bus Feedback
8-53 Start Select 8-94 Bus feedback 1
[0] Digital input -32768–32767, * 0
[1] Bus 13-** Smart Logic
[2] Logic AND 13-0* SLC Settings
*[3] Logic OR 13-00 SL Controller Mode
8-54 Reversing Select *[0] Off
[0] Digital input [1] On
[1] Bus 13-01 Start Event
[2] Logic AND [0] False
*[3] Logic OR [1] True
8-55 Set-up Select [2] Running
[0] Digital input [3] In range
[1] Bus [4] On reference
[2] Logic AND [7] Out of current range
*[3] Logic OR [8] Below I
8-56 Preset Reference Select [9] Above I
[0] Digital input
[16] Thermal warning
[1] Bus
[17] Mains out of range
[2] Logic AND
[18] Reversing
*[3] Logic OR [19] Warning
8-7* Bacnet [20] Alarm (trip)
8-70 BACnet Device Instance
[21] Alarm (trip lock)
0–0x400000UL
[22] Comparator 0
* 1
[23] Comparator 1
8-72 MS/TP Maxmaster
[24] Comparator 2
0–127, * 127
[25] Comparator 3
8-73 MS/TP Max Info Frames [26] Logic rule 0
1–65534, * 1
[27] Logic rule 1
8-74 "I am" Service
[28] Logic rule 2
*[0] Send at power-up
[29] Logic rule 3
[1] Continuously
[33] Digital input 18
8-75 Initialization Password
[34] Digital input 19
8-8* FC Port Diagnostics
[35] Digital input 27
8-80 Bus Message Count [36] Digital input 29
0–65536, * 0
*[39] Start command
[40] Drive stopped
[41] Reset trip
[42] Auto reset trip
low
high