Danfoss VLT 8000 AQUA series Operating Instructions Manual page 39

Technical data, mains supply 3 x 380 - 480 V
According to international requirements
Output current
Output power
Typical shaft output
Typical shaft output
Max. cable cross-section to
motor and DC-bus, IP 20
Max. cable cross-section to
motor and DC-bus, IP 54
Min. cable cross-section to
motor and DC-bus
Max. input current
(RMS)
Max. cable cross-section
power, IP 20
Max. cable cross-section
power, IP 54
Max. pre-fuses
Efficiency at rated frequency
Weight IP 20/NEMA 1
Weight IP 54/NEMA 12
Power loss at max. load.
Enclosure
1. For type of fuse, see section Fuses.
2. American Wire Gauge.
3. Measured using 30 m/100 ft screened motor cables at rated load and rated frequency.
4. Min. cable cross-section is the smallest cable cross-section allowed to be fitted on the terminals. Max. cable
cross section is the maximum possible cable cross section that can be fitted on the terminals.
Always comply with national and local regulations on min. cable cross-section.
MG.83.A2.02 - VLT is a registered Danfoss trademark
VLT
VLT type 8016
I [A] (380-440 V) 24.0
VLT,N
I (60 s) [A]
VLT, MAX
26.4
(380-440 V)
I [A] (441-480 V) 21.0
VLT,N
I (60 s) [A]
VLT, MAX
23.1
(441-480 V)
S [kVA] (400 V) 17.3
VLT,N
S [kVA] (460 V) 16.7
VLT,N
P [kW] 11
VLT,N
P [HP] 15
VLT,N
16/6
2 2) 4)
[mm ]/[AWG]
16/6
2 2) 4)
[mm ]/[AWG] 10/8
I [A] (380 V) 24.0
L,N
I [A] (480 V) 21.0
L,N
16/6
2 2) 4)
[mm ]/[AWG]
16/6
1)
[-]/UL [A] 63/40
0.96
[kg/lbs] 21/46
[kg/lbs] 41/90
[W] 419
®
8000 AQUA
8022 8027 8032
32.0 37.5 44.0
35.2 41.3 48.4
27.0 34.0 40.0
29.7 37.4 44.0
23.0 27.0 31.6
21.5 27.1 31.9
15 18.5 22
20 25 30
16/6 16/6 35/2
16/6 16/6 16/6
10/8 10/8 10/8
32.0 37.5 44.0
27.6 34.0 41.0
16/6 16/6 35/2
16/6 16/6 16/6
63/40 63/50 63/60
0.96 0.96 0.96
21/46 22/49 27/60
41/90 42/93 42/93
559 655 768
IP 20/NEMA 1/ IP 54/NEMA 12
8042
61.0
67.1
52.0
57.2
43.8
41.4
30
40
35/2
35/2
10/8
60.0
53.0
35/2
35/2
80/80
0.96
28/62
54/119
1065
39