Table of Contents
Advertisement
WIRE DESIGNATIONS FOR MAIN HARNESS
7-PIN
4-PIN
CIRCUIT
CONN
TOWER
1
D
GROUND
2
WORK LAMPS
3
B
LEFT FLASHING
& TURN
4
STOP LAMPS
5
A
RIGHT FLASHING
& TURN
6
C
TAIL LAMPS
7
SWITCHED
POWER (12V)
m177210 wire designations op
Figure 3-14: 7 Pin Connector Detail and Wiring Chart (After August, 2013)
LED Light and SMV Bracket
Installation (2410-7-24) (After
August, 2013)
NOTES
• See Figures 2-1 thru 2-3 for light bracket placement.
If no dimension is given for a bracket, it should be
located against frame member as shown in drawing.
• See Figure 3-13 for Light and SMV Bracket
Installation for 2410-7-24 model.
IMPORTANT
Make sure lights are positioned for maximum
visibility from the rear.
1. Attach left and right front brackets w/ yellow reflectors
and ag amber LED single lamps to frame using
1/4-20 x 1-1/4 hex head cap screws and hex lock
nuts (See Figure 3-13.)
2. Attach left and right rear brackets w/ red and orange
reflectors and ag amber LED single lamps to frame
using 1/4-20 x 1-1/4 hex head cap screws and hex
lock nuts.
3. Attach left tail light mount to frame assembly using
light mount bracket, 5/8-11 x 11-1/2 hex head cap
screws, and 5/8-11 hex lock nuts.
4. Attach ag flasher control module to right tail light
mount using 1/4-20 x 1-1/2 hex head cap screws and
hex lock nuts. Be sure that the control module is set
so that the 4 pin connector faces the right side of the
machine.
5. Attach right tail light mount w/ ag flasher control
module to frame assembly using light mount bracket,
5/8-11 x 11-1/2 hex head cap screws, and 5/8-11 hex
lock nuts.
WIRE DESIGNATIONS FOR REAR HARNESS
WIRE
COLOR
GROUND
BLACK
YELLOW
RED
GREEN
BROWN
BLUE
6. Attach the ag red single LED lamps and reflector
7. Attach front warning harness to frame. Connect 4 pin
NOTE
Figure 3-13 is labeled with letters assigned for each
harness connection to assist in proper lighting intentions.
8. Install the rear warning light harness to the frame.
9. Connect 6 pin end of the ag flasher control module
10. Connect 2 pin ends to each of the splitter wiring
11. Connect short end of the splitter wiring harnesses
12. Connect long end of each splitter wiring harnesses
13. Connect 3 pin ends of the rear warning light harness
14. Insure that the harnesses are clear of any moving
15. Install the stor-away holder to hose holder on hitch
16. Attach SMV emblem and mounting bracket to rear
ASSEMBLY INSTRUCTIONS
1
2
2-PIN
3-PIN
TOWER
TOWER
A
A
B
B
C
assemblies to tail light mounts using 1/4-20 x 1-1/4
hex head cap screws and hex lock nuts.
end (A) to the two 34" extension harnesses (B and
C), and the ag flasher control module (C) (See
Figure 3-13.)
(D) to the rear warning light harness (D).
harnesses (E).
(F) to the front amber lights (F).
(G) to the rear amber lights (G).
(H) to each of the red tail lights. See Figure 3-14 for
LED harness wire designations.
parts and secure the harnesses with tie wraps
provided.
with 1/4-20 x 3/4 hex head cap screws and hex lock
nuts.
center frame bar using 1/2-13 x 5-1/2 hex head cap
screws, 1/4-20 x 3/4 hex head cap screws, and hex
lock nuts. The SMV sign should be centered on the
rear bar of the frame.
3
4
5
6-PIN
3-PIN
2-PIN
SHROUD
TOWER
TOWER
A
C
B
A
A
C
B
B
D
E
F
3-21
Advertisement
Table of Contents
