Summary of Contents for Landoll Icon 1205 Carry All
Page 1
Model 1205 Carry All Service and Parts Manual LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-880-0118...
Page 2
Literature Information Maintenance This information should be stored in the The maintenance section is a guide to literature holder located on the machine. machine care. The illustrated step by step This manual contains safety information, procedures covers the most important of the operating instructions, lubrication and maintenance schedule.
Page 3
Index Safety Information Product Warranty Standard Specifications Hook Up & Operation Parts Listing Parts And Bolt Location Bolt Listing Hydraulics Decal Listing...
10 days of purchase or lease, in able to follow the suggestions made. Please take time to order to be on file at Landoll and eligible for Warranty. understand the proper maintenance schedule and SAFE Take time to read and understand the Warranty for this operation of your equipment.
Page 5
LANDOLL, including but not limited to, LANDOLL shall not provide Warranty on any part or component that has failed due to abuse, misuse, alt tenance, or normal wear ailure occurring while being pulled by a tractor in excess of engine...
Understanding Safety Statements NOTE You should read and understand the information You will find various types of safety information on the contained in this manual and on the machine decals following pages and on the machine decals (signs) before you attempt to operate or maintain this equipment. attached to the implement.
Page 7
Safety Decals Lubrication See Decal Listing for decal locations. 1. Lubrication information is placed near each zerk. 2. Proper maintenance should be followed to assure the NOTE working life of the machine. Replace all missing or damaged safety signs/decals. Proper Notification Pinching or Crushing Danger 1.
General Torque Specifications (rev. 4/97) TORQUE SPECIFIED IN FOOT POUNDS - This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and cap-screws assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.
Hydraulic Fitting Torque Specifications TORQUE IS SPECIFIED IN FOOT POUNDS- 37 JIC, ORS, & ORB (REV. 10/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).
Page 12
Section 02 Hookup and Operation utilizes three hydraulic valves on the tractor, allowing it to function in three different directions. The Carry All has the ability to raise to a clearance from bit to ground of 18 inches while lowering to a negative cut. It can tilt from corner to corner approximately 15 degrees to accomplish slope cuts and ditching.
Page 13
The tongue assembly is bolted on, and is removable for ease of transportation. It uses (16) 7/8 x 2 1/2” hex bolts, hard flat washers and hex nuts, and the top (6) are 7/8 x 3 1/2” to allow for the extra plate of the bolt on top cylinder support.
Page 14
Carry All 1205 4000100 4 x 16 4000371 4 1/2 x 16 Depth Gauge SCR2072 4000135 Manifold block (2) 4000136 Hyd Check SCR2065 1/2” x 4” 1/2” x 3” Axle support pin washer, & nylock nut nylock nut Axle supports are SCR2062L & R Hubs are GRA1966 (4), they are 8 bolt, rated at GRA1600 Cylinder Pin...
Page 18
Shown are the (5) hydraulic hoses. Note the Tee in the tilt circuit. The hose stand is ICO0004 It is attached with (2) 1/2 x 1 1/2” bolts and nyloc nuts, flat washers. The hoses are clamped with (1) 1/2 x 2 1/2” bolt, nyloc nut, and flat washer.
Page 19
Carry All 1205 SCR2064 Cylinder Support Mounts with (8) 3/4 x 2 12” bolts, flat hard washers and hex nuts. Hoses are all clamped using 3/8 x 2” bolts, flat washers and flange nut.
Page 20
Carry All 1205 SCR2073 The plastic (SCR2075) is bolted to the plastic holder (SCR2073) using (6) 3/8 x 1 1/4 flat head bolts.
Page 21
Carry All 1205 The clam SCR2063 pivots on (2) 1 1/2” pins. SCR2066 is 6” and SCR2070 is 84”. The long (84”) pin should be installed in the right side (from behind machine), due to an inner guide tube welded in to aid in the insertion of the pin.
Page 22
Carry All 1205 SCR2064 The plastic holder(SCR2075) is attached to the frame with the front cylinder support (SCR2064) and (4) 3/4 x 11” bolts, hard flat washers and hex nuts. SCR2075 SCR2073 plastic supp. SCR2075 Plastic 3/8 x 1 1/4” flat head...
Page 23
Carry All 1205 The side router bits are bolted on with 5/8 x 2 ” bolts, hard flat washers and hex nuts. (4 per side) The router bits are #4000359 Cutting Edges are (2) 4000125 They are 6’ each and attach using 5/8 x 2 1/2”...
Page 24
Carry All 1205 The hitch used on the Carry All 1205 is a pintel style 4001501, rated at 68,800 lbs. It is attached to the tongue using (2) 1 x 7 1/2” bolts, hard flat washers and nyloc nuts. A bolt on, optional top strap 4001503 is available for use on tractors without a hammer strap on the drawbar.
Page 25
Carry All 1205 Parts Listing Part # Description 4000125 Cutting Edges 6’DBC245600 5001197 Hyd. Fitting Kit SCR2026 Cylinder Mount 5001184 Hyd. Hose Kit ICO2283 Box Frame ICO2287 Hitch Frame ICO2288 Tongue Frame ICO0004 Hose Stand SCR2062R Axle Support (right) SCR2062L Axle Support (left) SCR2063 Clam...
Page 26
Carry All 1205 Bolt Listing # 2000632 Part # Description and Location Hub To Axle Support BH 3/4 x 6 1/2” Bolt, Hex 3/4 x 6 1/2” gr 8 WFH 3/4 Washer, Flat, Hard 3/4” NH 3/4 Nut, Hex 3/4” gr 8 Cyl.
Page 27
Bolt Listing - Cont. Part # Description and Location Cylinder Bushings 4000150 Bushing, 125100100 Pin Keepers BH 1/2 x 3” Bolt, Hex 1/2 x 3” gr 5 NL 1/2 Nut, Nyloc 1/2” gr 2 PR 5/16 x 2” Pin, Roll 5/16 x 2” WF 1”...
Page 35
Part # 2000629 Part # Description 4000372 Warning Moving Parts 4000940 Danger Pinch 4000931 Warning High Pressure 4000935 Parts Manual 4001522 Landoll/ICON 4001285 HP Listing (140) 4000941 Danger/Safe/Maint 4000335 Slow Moving Vehicle 4001533 Reflective Tape (Orange) 4001534 Reflective Tape (Red) 4001535...
Page 36
Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Model 1205 Carry All Service and Parts Manual Re-Order Part Number F-880-0118 LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...
Need help?
Do you have a question about the Icon 1205 Carry All and is the answer not in the manual?
Questions and answers