Barco BARCOVISION 8100 Owner's Manual page 54

Set up of the baud rate for communication with a computer.
The communication speed between projector and computer, e.g. PC or MAC, has 8
possible speeds. With DIP switches S2(1,2,3) on the controller unit, it is possible to
select the baud rate (communication speed).
Gaining access to the DIP switches
Power down the projector and unplug the power cord from the wall outlet.
Turn both lock screws with a screwdriver or coin counter clockwise.
Lift up and pivot the top cover. Attention : the cover is not secured with an
incorporated support. When opening, turn it over slowly and lay it down on the
second part of the top cover.
The processor module with the DIP switches is located on top, the front left side
(seen from the front of the projector, see next page).
Loosen the locking
screws.
R
RS232 OUT
Open the top cover
R
RS232 OUT
7-14
CONNECTIONS
V
B
B
V
This device complies with Part 15 of the FCC rules. Operation
is subject to following two conditions :
(1) T his device may not c ause harmf u l interference
DI AGNOSTICS (2) Thi s device must accept any i n terference received
incl u ding interference that may cause undesired operat i on
CODE I R-RECEIVER
R I R-ACKNO WLEDGED
0 I
I R-RECEI VED
V
B
B
V
This device complies with Part 15 of the FCC rules. Operation
is subject to following two conditions :
(1) T his device may not c ause harmf u l interference
DI AGNOSTICS (2) Thi s device must accept any i n terference received
CODE incl u ding interference that may cause undesired operat i on
I R-RECEI VER
R I R-ACKNOWLEDGED
0 I
I R-RECEIVED
5975036 BARCOVISION 8100 150197
100 - 230 V
9 - 4 A
60 - 50 Hz
100 - 230 V
9 - 4 A
60 - 50 Hz
7-14
Set up of the baud rate for communication with a computer.
The communication speed between projector and computer, e.g. PC or MAC, has 8
possible speeds. With DIP switches S2(1,2,3) on the controller unit, it is possible to
select the baud rate (communication speed).
Gaining access to the DIP switches
Power down the projector and unplug the power cord from the wall outlet.
Turn both lock screws with a screwdriver or coin counter clockwise.
Lift up and pivot the top cover. Attention : the cover is not secured with an
incorporated support. When opening, turn it over slowly and lay it down on the
second part of the top cover.
The processor module with the DIP switches is located on top, the front left side
(seen from the front of the projector, see next page).
Loosen the locking
screws.
B
V
R
RS232 OUT
Open the top cover
B
V
R
RS232 OUT
CONNECTIONS
B V
This device complies with Part 15 of the FCC rul e s. Operation
is subject to following two conditions :
(1) T his devi c e may not cause harmful interference
DIAGNOSTICS (2) This device must accept any interference received
incl u ding interf e rence that m ay cause undesired operat i on
CODE I R-RECEI VER
I R-ACKNOWLEDGED
R 100 - 230 V
0 I 9 - 4 A
60 - 50 Hz
I R-RECEI VED
V
B
This device complies with Part 15 of the FCC rul e s. Operation
is subject to following two conditions :
DI AGNOSTICS (1) T his devi c e may not cause harmful interference
(2) This device must accept any interference received
CODE incl u ding interf e rence that m ay cause undesired operat i on
I R-RECEIVER
R I R-ACKNO WLEDGED
100 - 230 V
9 - 4 A
0 I
60 - 50 Hz
I R-RECEI VED
5975617 BARCOVISION 8100 150197