Barco BARCOVISION 8100 Owner's Manual page 47

CONNECTIONS
PROJ ECTOR MO DE :
IR-ACKNOWLEDGED
R R RED - STANDBY
RS232 OUT RS 232 IN REMOTE
G
G
IR-RECEIVED
ANALOG INTERFACE 120 MHz
ON
INPUT
B
H V
OFF
R G
INP INP
RGB input selection :
Key in the corresponding slot number on the RCU or the local keypad.
Straps on module level :
Floating or non-floating input.
Red : J3 : strap "yes" : non floating
Green : J4 : strap "yes" : non floating
Blue : J5 : strap "yes" : non floating
H/C : J6 : strap "yes" : non floating
V : J7 : strap "yes" : non floating
Factory preset : strap "yes", non floating input
5975617 BARCOVISION 8100 150197
This device complies with Part 15 of the FCC rul e s. Operation
is subject to followi n g two conditions :
(1) Thi s device may not cause harmful interference
DIAGNOSTICS
(2) Thi s device must accept any i n terference received
CODE incl u ding interference that may cause undesired operation
IR-RECEIVER
10 0 - 23 0 V
9 - 4 A
0 I
6 0 - 50 Hz
AAAA AAAA AAAA A
AAAA AA AAAA AAAA A A
AAAA AA AAAA AAAA
AAAA AAAA AAAA A A
AAAA AAAA AAAA
AAAA AAAA AAAA A
AAAA AAAA AAAA A A
AAAA AAAA AAAA
strap "no" : floating
strap "no" : floating
strap "no" : floating
strap "no" : floating
strap "no" : floating
CONNECTIONS
RS232 OUT
ANALOG INTERFACE 120 MHz
ON
OFF
R
RGB input selection :
Key in the corresponding slot number on the RCU or the local keypad.
Straps on module level :
Floating or non-floating input.
Red : J3 : strap "yes" : non floating
Green : J4 : strap "yes" : non floating
Blue : J5 : strap "yes" : non floating
H/C : J6 : strap "yes" : non floating
V : J7 : strap "yes" : non floating
Factory preset : strap "yes", non floating input
7-7 5975617 BARCOVISION 8100 150197
PRO J ECTO R MO DE :
DIAGNOSTICS
CODE
IR-RECEIVER
IR-ACKNOWLEDGED
R R RED - STANDBY
RS 232 IN
REMOTE
G
G
IR-RECEIVED
INPUT
B H
V
G INP
INP
strap "no" : floating
strap "no" : floating
strap "no" : floating
strap "no" : floating
strap "no" : floating
This device complies with Part 15 of the FCC rul e s. Operation
is subject to followi n g two conditions :
(1) Thi s device may not cause harmful interference
(2) Thi s device must accept any i n terference received
incl u ding interference that may cause undesired operation
10 0 - 23 0 V
9 - 4 A
0 I
6 0 - 50 Hz
AAAA AAAA AAAA A
AAAA AA AAAA AAAA A
AAAA AAAA AAAA A
AAAA AAAA AAAA A
A
AAAA AAAA AAAA
AAAA AAAA AAAA A
AAAA AAAA AAAA A
7-7