HEIDENHAIN TNC 370 User Manual page 329

Stichwortverzeichnis
4
A
Actual position capture ................ .4-24
Additional axes ............................. I-20
Arc radius R ................................. 5-20
Axis traverse limits ....................... 1 1-4
B
Basic rotation ................................ .9-7
Cancelling ................................... 9-8
Displaying ................................... 9-8
BAUD RATE ................................. 1 l-5
Blank form definition
.................. ..4- 1 9
Blocks
Erasing ....................................... 4-4
Inserting ..................................... 4-3
Marking blocks to be skipped
..4-2 5
Selecting .................................... .4-3
to be skipped during
program run ........................... .3-7
Blockwise transfer ......................... .3-6
Boring ............................................. 8-9
C
Cartesian coordinate system ....... l-l 9
Circle center CC ................ 5-14, 5-l 5
Programming
............................ 5-16
Circular pattern ............................. 8-35
Circular pocket
Finishing ................................... 8-23
Roughing .................................. 8-22
Circular slot .................................. 8-30
Circular stud
Finishing
................................... 8-25
Code numbers .............................. 1 1-7
Contour ........................................... 5-4
Approaching ...................... 5-4, 5-6
Departing
........................... 5-5, 5-6
Contour line digitizing ................... 9-26
Coordinate transformations ........ .8-60
Cycle
PROGRAM CALL ..................... 8-68
Cycles
Calling ......................................... 8-4
Defining ...................................... 8-3
Graphic support ......................... 8-3
D
Data interface ............................... 1 O-3
Pin layout .................................. 1 O-3
Setting ...................................... 1 1-5
Data transfer ................................ 1 O-4
HEIDENHAIN devices .............. 1 O-4
Non-HEIDENHAIN devices ..... .I O-4
D
Datum setting ............................... I-21
General information
.. . ............. .I-21
with the 3D touch probe .............. 9-9
at a circle center ................... 9-1 2
corner as datum ................. ..9- 10
in a specific axis .................... .9-9
without a 3D touch probe .......... .2-7
in the tool axis ....................... .2-7
in the working plane .............. .2-8
Datum shift ................................... 8-61
Dialog ............................................. 4-2
Digitized data
Use .......................................... .9-29
Digitizing ....................................... 9-21
CONTOUR LINES cycle .......... 9-26
MEANDER cycle ..................... .9-24
RANGE cycle
........................... 9-22
Using digitized data .................. 9-29
Direction of rotation DR ................ 5-l 4
Display modes .............................. 1-27
3D view ..................................... 1-29
Detail magnification .............. I-30
Rotating ................................
1-29
Interactive graphics .................. 1-34
Plan view .................................. 1-27
Projection in three planes ........ I-28
Moving sectional planes ....... 1-28
Distance-to-go .............................. 1-23
Drilling ............................................. 8-7
Drilling with chip breaking
........... .8-10
Dwell time .................................... .8-68
E
Ellipse ........................................... 7-l 8
Entering comments ...................... 4-26
Error messages .......................... 12-l 7
External data transfer
.................. 1 o-2
F
Feed rate
Changing .................................... 2-6
Duration .................................... 4-21
Free contour programming
Circular arcs ............................. 5-44
Auxiliary points
.................... .5-47
Closed contours ...................... .5-47
Contour elements ..................... 5-36
Examples for exercise ............. .5-48
FK Functions ............................ 5-39
General information ........ 5-2, 5-36
Interactive graphics .................. 5-38
Several solutions ...................... 5-38
Straight lines ............................ 5-40
Slope .................................... 5-41
Free memory
Displaying .................................
11-7
Full circle ........................... 5-l 9, 5-31
Fundamentals of NC .................... l-l 8
4
G
Graphic simulation ....................... I-30 ~
H
Handwheel ..................................... 2-3 -/
Helical interpolation ..................... .5-33
Helix .............................................. 5-33
HELP function .............................. 1 1-8
Hemisphere .................................. 7-20
Hexagon
Milling ...................................... .5-29
I
If-then operations ......................... .7-9
L
Linear pattern ............................... 8-36
M
M Functions ................................ 12-1 0
Machine parameters 12-2 - ....................
Machine-specific user parameters 1 1-2
Machining corners ........................ 4-18
Main program as subprogram
\--/
Calling ......................................... 6-8
Operating limits ......................... .6-8
Principle ......................................
6-8
Mathematical functions .................. 7-6 -
Mirror image ................................. 8-63
Miscellaneous function M .............. .2-6
Completely machining open
contours: M98 ...................... 5-53
Displaying rotary axes: M94 ... .5-55
Entering ........................... 2-6, 4-23 _,
Feed rate at circular arcs:
Ml09 .................................... 5-56
Machining contour steps: M97 .5-52
Setting the coordinates for the
datum: M91/M9 .................... 5-54
Smoothing corners: M90 ......... .5-51
Traversing rotary axes: Ml26 ., 5-55 -
Miscellaneous Functions
Overview ................................ 12-l 0
MODfunctions
4
Exiting .......................................
1 l-2
Selecting ................................... 1 1-2
Moving the machine axes .............. 2-2 -
With incremental jog positioning 2-4
With the axis direction keys ..... ..2- 2
With the handwheel ................... 2-3
Multipass milling ........................... 8-55
N
NC ................................................ 1-18 -
NC software number .................... 1 1-7
Nesting ........................................... 6-9
Nesting depth ................................. 6-9 -
TNC 426