ProCurve 9304m Diagnostics Manual page 47

After you enter this command, messages such as the following appear at the destination specified for debugging
output. You can turn off these messages with the no debug ipv6 ospf lsa-refresh command.
OSPFv3 LSA Update Intra-Area-Prefix(Stub): Checking Interface 137
OSPFv3 LSA Update Intra-Area-Prefix(Stub): Interface 137 is down
OSPFv3 :LSA Update Intra-Area-Prefix(Stub): No prefix to advertise for Area
0.0.0.0
OSPFv3 :LSA Update Intra-Area-Prefix(Stub): Area 0.0.0.0
ospf1(config-ospf6-router)#LSA: Update Router-LSA for area 0.0.0.0
OSPFv3 LSA Update Intra-Area-Prefix(Stub): Checking Interface 137
OSPFv3 LSA Update Intra-Area-Prefix(Stub): include 3000:1::2/64
OSPFv3 :LSA Update Intra-Area-Prefix(Stub): Area 0.0.0.0
OSPFv3 :LSA Update Link: Interface 137
LSA: Update Router-LSA for area 0.0.0.0
OSPFv3 LSA Update Intra-Area-Prefix(Stub): Checking Interface 137
OSPFv3 LSA Update Intra-Area-Prefix(Stub): include 3000:1::2/64
OSPFv3 :LSA Update Intra-Area-Prefix(Stub): Area 0.0.0.0
OSPFV3: LSA[2.2.2.2]: request 1.2.3.40 (newer)
OSPFV3 LSA[2.2.2.2]: request Type =8193 ADvRtr =2.2.2.2 ID=0
OSPFV3 LSA[2.2.2.2]: request Type =8201 ADvRtr =2.2.2.2 ID=0
OSPFV3 LSA[2.2.2.2]: request Type =8 ADvRtr =2.2.2.2 ID=136
OSPFv3 : LSA[575305040]: delayed ack
LSA: Update Router-LSA for area 0.0.0.0
OSPFv3 : LSA[575305040]: delayed ack
OSPFv3 : LSA[575305040]: delayed ack
OSPFv3 LSA Update Intra-Area-Prefix(Stub): Checking Interface 137
OSPFv3 LSA Update Intra-Area-Prefix(Stub): Interface 137 is not stub
OSPFv3 :LSA Update Intra-Area-Prefix(Stub): No prefix to advertise for Area
0.0.0.0
OSPFv3 :LSA Update Intra-Area-Prefix(Stub): Area 0.0.0.0
LSA: Update Router-LSA for area 0.0.0.0
OSPFv3 : LSA[575305040]: delayed ack
OSPFv3:LSA[2.2.2.2]: direct ack
OSPFv3 : LSA[575305040]: delayed ack
OSPFv3:LSA[2.2.2.2]: direct ack
OSPFv3:LSA[2.2.2.2]: direct ack
OSPFv3:LSA[2.2.2.2]: direct ack
OSPFv3 : LSA[575305040]: delayed ack
Syntax: [no] debug ipv6 ospf lsa-refresh
Possible values: N/A
Default value: N/A
debug ipv6 ospf nsm
Displays comprehensive information about the status changes of OSPF version 3 neighbors. The debug ipv6
ospf nsm-status command displays status change messages only. For more information, see "debug ipv6 ospf
ism-status" on page 3-29.
EXAMPLE:
ProCurveRS debug ipv6 ospf nsm
June 2005
HP Diagnostic Command Reference
3 - 33