ProCurve 9304m Diagnostics Manual page 44

Diagnostic Guide for ProCurve 9300/9400 Series Routing Switches
After you enter this command, messages such as the following appear at the destination specified for debugging
output. You can turn off these messages with the no debug ipv6 ospf ism-status command.
OSPFv3 ISM[137]: Status change Down -> Waiting (Priority > 0)
OSPFv3 ISM[137]: Status change Waiting -> BDR (Backup Seen:DR Election)
OSPFv3 ISM[137]: {dr:0.0.0.0,bdr:0.0.0.0} -> {dr:2.2.2.2,bdr:1.2.3.4}
Syntax: [no] debug ipv6 ospf ism-status
Possible values: N/A
Default value: N/A
debug ipv6 ospf lsa
Displays information when an OSPF version 3 router generates link-state advertisements (LSAs).
EXAMPLE:
ProCurveRS debug ipv6 ospf lsa
After you enter this command, messages such as the following appear at the destination specified for debugging
output. You can turn off these messages with the no debug ipv6 ospf lsa command.
OSPFv3 LSA Update Intra-Area-Prefix(Stub): Checking Interface 137
OSPFv3 LSA Update Intra-Area-Prefix(Stub): Interface 137 is down
OSPFv3 :LSA Update Intra-Area-Prefix(Stub): No prefix to advertise for Area
0.0.0.0
OSPFv3 :LSA Update Intra-Area-Prefix(Stub): Area 0.0.0.0
ospf1(config-ospf6-router)#OSPFv3 ISM[137]: Status change Down -> Waiting
(Priority > 0)
LSA: Update Router-LSA for area 0.0.0.0
OSPFV3 LSA: Create LSA
OSPFv3 LSA Update Intra-Area-Prefix(Stub): Checking Interface 137
OSPFv3 LSA Update Intra-Area-Prefix(Stub): include 3000:1::2/64
OSPFV3 LSA: Create LSA
OSPFv3 :LSA Update Intra-Area-Prefix(Stub): Area 0.0.0.0
OSPFv3 :LSA Update Link: Interface 137
OSPFV3 LSA: Create LSA
OSPF6: Inter Area LSA not generated, route is in same area.
OSPFv3 LSA Update Intra-Area-Prefix(Stub): Checking Interface 137
OSPFv3 LSA Update Intra-Area-Prefix(Stub): include 3000:1::2/64
OSPFV3 LSA: Create LSA
OSPFv3 LSA: Turnover type:IntraPrefix Lsa Id:0.0.0.0 AdvRouter:1.2.3.4: contents
not changed
OSPFV3 LSA: Delete LSA Type :IntraPrefix Id: 0.0.0.0 Advrouter: 1.2.3.4
OSPFv3 :LSA Update Intra-Area-Prefix(Stub): Area 0.0.0.0
Syntax: [no] debug ipv6 ospf lsa
Possible values: N/A
Default value: N/A
debug ipv6 ospf lsa-flooding
Displays information when an OSPF version 3 router floods LSAs to neighboring routers to update them about its
interfaces.
EXAMPLE:
ProCurveRS debug ipv6 ospf lsa-flooding
3 - 30
Type :Router Id: 0 Advrouter: 1.2.3.4
Type :IntraPrefix Id: 0 Advrouter: 1.2.3.4
Type :Link Id: 137 Advrouter: 1.2.3.4
Type :IntraPrefix Id: 0 Advrouter: 1.2.3.4
June 2005