Table of Contents
Advertisement
ZBAS ( Returns the number of the BASIC task area in which the program currently being created ) ..... 11-405
ZCLOSE ( Closes a communication channel ) ........................................................................................... 11-406
ZCNTL
11-407
ZCNTL - Processing Code 16 - (Specifying communication parameter)................................................. 11-409
ZCNTL - Processing Code 17 - (Reading communication parameters) .................................................. 11-409
ZCNTL - Processing Code 18 - (Specifying communication control parameters)................................... 11-411
ZCNTL - Processing Code 19 - (Reading communication control parameters) ...................................... 11-411
ZCNTL - Processing Code 22 - (Specifying break characters) ................................................................ 11-414
ZCNTL - Processing Code 23 - (Reading break characters) ................................................................... 11-414
ZCNTL - Processing Code 24 - (Specifying continuous break characters) ............................................. 11-416
ZCNTL - Processing Code 25 - (Reading continuous break characters) ................................................ 11-416
ZCNTL - Processing Code 32 - (Turning ON/OFF the RS and ER control signals)................................ 11-418
ZCNTL - Processing Code 33 - (Reading the ON/OFF status of the CS, DR, RS, ER and CD
control signals)........................................................................................................................ 11-420
ZCNTL - Processing Code 48 - (Specifying high impedance control) ..................................................... 11-422
ZCNTL - Processing Code 64 - (Reading causes of reception errors) .................................................... 11-423
ZCNTL - Processing Code 80 - (Reading the receive buffer size and the number of characters) ......... 11-425
ZCNTL - Processing Code 96 - (Specifying Kanji code conversion)........................................................ 11-426
ZCNTL - Processing Code 100 - (Specifying Kanji shift in/out codes)..................................................... 11-427
ZCNTL - Processing Code 128 - (Reading the printer status) ................................................................. 11-430
ZCNTL - Processing Code 136 - (Outputting the initialization signal to the printer) ................................ 11-432
ZEVENT ( Enables or disables event generation ) ..................................................................................... 11-433
ZIDV ( Specifies the data input device for the INPUT instruction, etc ) ..................................................... 11-434
ZLDV ( Selects a communication port for a printer ) ................................................................................... 11-435
ZMESSAGE ( Defines a message port ) ..................................................................................................... 11-436
ZMESSAGE CLOSE ( Closes message ports ) .......................................................................................... 11-439
ZMESSAGE GET ( Reads messages from message ports ) ..................................................................... 11-440
ZMESSAGE KILL ( Deletes the message ports ) ....................................................................................... 11-442
ZMESSAGE OPEN ( Opens a message port ) ........................................................................................... 11-443
ZMESSAGE PUT ( Writes messages to a message port ) ........................................................................ 11-444
ZMOVE ( Transfers data between valiables ) ............................................................................................. 11-446
ZODV ( Specifies the data output destination for the PRINT instruction, etc ) .......................................... 11-451
ZOPEN ( Opens a communication channel ) .............................................................................................. 11-452
ZRECEIVE ( Receives data from a communication channel ) ................................................................... 11-454
ZRELEASE ( Allows other programs to use a resource to which a resource number is assigned ) ........ 11-460
ZRESERVE ( Prohibits other programs from using a resource to which a resource number is
assigned ) ................................................................................................................................ 11-461
ZSEND ( Sends data from a communication channel ) .............................................................................. 11-463
ZSIGNAL ( Generates the specified event ) ................................................................................................ 11-469
ZSTART ( Starts up the specified program ) ............................................................................................... 11-470
ZURGENCY ( Changes the priority of a program ) ..................................................................................... 11-472
ZWAIT DELAY ( Pauses the program execution until the specified time has elapsed ) ........................... 11-473
ZWAIT EVENT ( Pauses the program execution until the specified event is generated ) ........................ 11-474
A - 11
A - 11
Advertisement
Table of Contents
