YASKAWA A1000 Technical Manual page 104

4.6 Basic Drive Setup Adjustments
n H1-01 to H1-08: Functions for Terminals S1 to S8
These parameters assign functions to the multi-function digital inputs. The various functions and settings are listed in
4.25.
No.
H1-01 Multi-Function Digital Input Terminal S1 Function Selection
H1-02 Multi-Function Digital Input Terminal S2 Function Selection
H1-03 Multi-Function Digital Input Terminal S3 Function Selection
H1-04 Multi-Function Digital Input Terminal S4 Function Selection
H1-05 Multi-Function Digital Input Terminal S5 Function Selection
H1-06 Multi-Function Digital Input Terminal S6 Function Selection
H1-07 Multi-Function Digital Input Terminal S7 Function Selection
H1-08 Multi-Function Digital Input Terminal S8 Function Selection
<1> Number appearing in parenthesis is the default value after performing a 3-Wire initialization.
Setting
0 3-Wire Sequence
1 LOCAL/REMOTE Selection
2 External Reference 1/2 Selection
3 Multi-Step Speed Reference 1
4 Multi-Step Speed Reference 2
5 Multi-Step Speed Reference 3
6 Jog reference Selection
7 Accel/Decel Time Selection 1
8 Baseblock Command (N.O.)
9 Baseblock Command (N.C.)
A Accel/Decel Ramp Hold
B Drive Overheat Alarm (oH2)
C Analog Terminal Input Selection
D PG Encoder Disable
E ASR integral reset
F Through Mode
10 Up Command
11 Down Command
12 Forward Jog
13 Reverse Jog
14 Fault Reset
15 Fast Stop (N.O.)
16 Motor 2 Selection
17 Fast Stop (N.C.)
18 Timer Function Input
19 PID Disable
1A Accel/Decel Time Selection 2
1B Program Lockout
1E Reference Sample Hold
20 to 2F External Fault
30 PID Integral Reset
31 PID Integral Hold
32 Multi-Step Speed Reference 4
104
Parameter Name
Table 4.25 Multi-Function Digital Input Terminal Settings
Function
Setting
Range
1 to 9F
40 (F)
1 to 9F
41 (F)
0 to 9F 24: External Fault
0 to 9F 14: Fault Reset
<1>
0 to 9F
3 (0)
<1>
0 to 9F
4 (3)
<1>
0 to 9F
6 (4)
0 to 9F 8: External Baseblock Command
Page Setting
105 34 PID Soft Starter Cancel
— 35 PID Input Level Selection
— 40 Forward Run Command (2-Wire sequence)
— 41 Reverse Run Command (2-Wire sequence)
— 42 Run Command (2-Wire sequence 2)
— 43 FWD/REV Command (2-Wire sequence 2)
— 44 Offset Frequency 1
— 45 Offset Frequency 2
— 46 Offset Frequency 3
— 47 Node Setup
— 60 DC Injection Braking Command
— 61 External Speed Search Command 1
— 62 External Speed Search Command 2
— 63 Field Weakening
— 65 KEB Ride-Thru 1 (N.C.)
— 66 KEB Ride-Thru 1 (N.O.)
— 67 Communications Test Mode
— 68 High Slip Braking
— 6A Drive Enabled
— 71 Speed/Torque Control Switch
— 72 Zero Servo
— 75 Up 2 Command
— 76 Down 2 Command
— 77 ASR Gain Switch
— 78 External Torque Reference Polarity Inversion
— 7A KEB Ride-Thru 2 (N.C.)
— 7B KEB Ride-Thru 2 (N.O.)
— 7C Short Circuit Braking (N.O.)
— 7D Short Circuit Braking (N.C.)
— Forward/Reverse Detection (V/f control with
7E
simple PG)
—
90 to 97 DriveWorksEZ Digital Input 1 to 8
—
9F DriveWorksEZ Disabled
—
YASKAWA ELECTRIC TOEP C710616 41B YASKAWA AC Drive - A1000 Quick Start Guide
Default
<1>
: Forward Run Command (2-Wire sequence)
<1>
: Reverse Run Command (2-Wire sequence)
: Multi-Step Speed Reference 1
: Multi-Step Speed Reference 2
: Jog Reference Selection
Function
Table
Page
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—