Danfoss VLT Decentral Drive FCD 302 Operating Manual page 54

Programming
8-19 Product Code
8-3* FC Port Settings
8-30 Protocol
8-31 Address
8-32 FC Port Baud Rate
8-33 Parity / Stop Bits
8-34 Estimated cycle time
8-35 Minimum Response Delay
8-36 Max Response Delay
8-37 Max Inter-Char Delay
5 5
8-4* FC MC protocol set
8-40 Telegram Selection
8-41 Parameters for Signals
8-42 PCD Write Configuration
8-43 PCD Read Configuration
8-5* Digital/Bus
8-50 Coasting Select
8-51 Quick Stop Select
8-52 DC Brake Select
8-53 Start Select
8-54 Reversing Select
8-55 Set-up Select
8-56 Preset Reference Select
8-57 Profidrive OFF2 Select
8-58 Profidrive OFF3 Select
8-8* FC Port Diagnostics
8-80 Bus Message Count
8-81 Bus Error Count
8-82 Slave Messages Rcvd
8-83 Slave Error Count
8-9* Bus Jog
8-90 Bus Jog 1 Speed
8-91 Bus Jog 2 Speed
5.3.10 9-** Profibus
Par- Parameter description
ameter #
9-00 Setpoint
9-07 Actual Value
9-15 PCD Write Configuration
9-16 PCD Read Configuration
9-18 Node Address
9-19 Drive Unit System Number
9-22 Telegram Selection
9-23 Parameters for Signals
9-27 Parameter Edit
9-28 Process Control
9-44 Fault Message Counter
9-45 Fault Code
9-47 Fault Number
52
®
VLT Decentral Drive FCD 302
ExpressionLimit 1 set-up
[0] FC 1 set-up
1 N/A 1 set-up
ExpressionLimit 1 set-up
[0] Even Parity, 1
Stop Bit 1 set-up
0 ms 2 set-ups
10 ms 1 set-up
ExpressionLimit 1 set-up
ExpressionLimit 1 set-up
[1] Standard
telegram 1 2 set-ups
0 All set-ups
ExpressionLimit 2 set-ups
ExpressionLimit 2 set-ups
[3] Logic OR All set-ups
[3] Logic OR All set-ups
ExpressionLimit All set-ups
[3] Logic OR All set-ups
[3] Logic OR All set-ups
[3] Logic OR All set-ups
[3] Logic OR All set-ups
[3] Logic OR All set-ups
[3] Logic OR All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
100 RPM All set-ups
ExpressionLimit All set-ups
Default value 4 set-up
0 N/A All set-ups
0 N/A All set-ups
ExpressionLimit 1 set-up
ExpressionLimit 2 set-ups
126 N/A 1 set-up
1034 N/A All set-ups
[100] None 1 set-up
0 All set-ups
[1] Enabled 2 set-ups
[1] Enable cyclic
master 2 set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
Danfoss A/S © 05/2016 All rights reserved.
TRUE 0
TRUE –
TRUE 0
TRUE –
TRUE –
TRUE -3
TRUE -3
TRUE -3
TRUE -5
TRUE –
FALSE –
TRUE 0
TRUE 0
TRUE –
TRUE –
TRUE –
TRUE –
TRUE –
TRUE –
TRUE –
TRUE –
TRUE –
TRUE 0
TRUE 0
TRUE 0
TRUE 0
TRUE 67
TRUE 67
Change during Conversion
operation index
TRUE 0
FALSE 0
TRUE –
TRUE –
TRUE 0
TRUE 0
TRUE –
TRUE –
FALSE –
FALSE –
TRUE 0
TRUE 0
TRUE 0
Uint32
Uint8
Uint8
Uint8
Uint8
Uint32
Uint16
Uint16
Uint16
Uint8
Uint16
Uint16
Uint16
Uint8
Uint8
Uint8
Uint8
Uint8
Uint8
Uint8
Uint8
Uint8
Uint32
Uint32
Uint32
Uint32
Uint16
Uint16
Type
Uint16
Uint16
Uint16
Uint16
Uint8
Uint16
Uint8
Uint16
Uint16
Uint8
Uint16
Uint16
Uint16
MG04F402