Telnet Command: Msubnet Nmask; Telnet Command: Msubnet Status; Telnet Command: Msubnet Dhcps - Draytek vigor2760 series User Manual
High speed vdsl2 router
Hide thumbs
Also See for vigor2760 series:
- User manual (430 pages) ,
- Quick start manual (39 pages) ,
- Quick start manual (25 pages)
Table of Contents
Advertisement
T
e
l
n
e
t
C
o
m
m
T
e
l
n
e
t
C
o
m
m
This command is used to configure net mask address for the specified LAN interface.
msubnet nmask [2][IP address]
S
y
n
t
a
x
S
y
n
t
a
x
Parameter
[2]
IP address
E
x
a
m
p
E
x
a
m
p
> msubnet nmask 2 255.255.0.0
% Set LAN2 subnet mask done !!!
This setting will take effect after rebooting.
Please use "sys reboot" command to reboot the router.
T
e
l
n
e
t
C
o
m
m
T
e
l
n
e
t
C
o
m
m
This command is used to display current status of subnet.
msubnet status [2]
S
S
y
y
n
n
t
t
a
a
x
x
Parameter
[2]
E
x
a
m
p
E
x
a
m
p
> msubnet status 2
% LAN2
% DHCP server: Off
% Dhcp Gateway: 0.0.0.0, Start IP: 0.0.0.10, Pool Count: 50
T
e
l
n
e
t
C
o
m
m
T
e
l
n
e
t
C
o
m
m
This command is used to enable the DHCP server for the specified LAN interface.
msubnet dhcps [2][On/Off]
S
y
n
t
a
x
S
y
n
t
a
x
Parameter
[2]
On/Off
Vigor2760 Series User's Guide
a
n
d
:
m
s
u
b
n
e
t
n
m
a
n
d
:
m
s
u
b
n
e
t
n
m
D
e
s
c
r
i
p
t
i
o
n
D
e
s
c
r
i
p
t
i
o
n
Description
It means LAN interface.
2=LAN2
Type the subnet mask address for the specified LAN
interface.
l
e
l
e
a
n
d
:
m
s
u
b
n
e
t
s
t
a
n
d
:
m
s
u
b
n
e
t
s
t
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
Description
It means LAN interface.
2=LAN2
l
e
l
e
Off: 0.0.0.0/0.0.0.0, PPP Start IP: 0.0.0.60
a
n
d
:
m
s
u
b
n
e
t
d
h
a
n
d
:
m
s
u
b
n
e
t
d
h
D
e
s
c
r
i
p
t
i
o
n
D
e
s
c
r
i
p
t
i
o
n
Description
It means LAN interface.
2=LAN2
On means enabling the DHCP server for the specified LAN
a
s
k
a
s
k
a
t
u
s
a
t
u
s
c
p
s
c
p
s
520
Advertisement
Table of Contents
