System Info; Start/Stop/Dir - ABB ACS850 Manual

124 Parameters
No. Name/Value
09

09 System info

09.01 Drive type
09.02 Drive rating ID
09.03 Firmware ID
09.04 Firmware ver
09.05 Firmware patch
09.10 Int logic ver
09.20 Option slot1
09.21 Option slot2
09.22 Option slot3
10

10 Start/stop/dir

10.01 Ext1 start func
Not sel
In1
Description
Drive type, program revision and option slot occupation
information.
Displays the drive type (for example, ACS850).
Displays the inverter type (ACS850-xx-...) of the drive.
0 = Unconfigured, 101 = 03A0, 102 = 03A6, 103 = 04A8,
104 = 06A0, 105 = 08A0, 106 = 010A, 107 = 014A,
108 = 018A, 109 = 025A, 110 = 030A, 111 = 035A,
112 = 044A, 113 = 050A, 114 = 061A, 115 = 078A,
116 = 094A, 117 = 103A, 118 = 144A, 119 = 166A,
120 = 202A, 121 = 225A, 122 = 260A, 123 = 290A,
124 = 430A, 125 = 521A, 126 = 602A, 127 = 693A,
128 = 720A, 141 = 03A0_2, 142 = 03A6_2, 143 = 04A8_2,
144 = 06A0_2, 145 = 08A0_2, 146 = 010A_2, 147 = 014A_2,
148 = 018A_2, 149 = 025A_2, 150 = 030A_2, 151 = 035A_2,
152 = 044A_2, 153 = 050A_2, 154 = 061A_2, 155 = 078A_2,
156 = 094A_2
Displays the firmware name. E.g. UIFI.
Displays the version of the firmware package in the drive, e.g.
E00F hex.
Displays the version of the firmware patch in the drive.
Displays the version of the logic on the main circuit board of
the drive.
Displays the type of the optional module in option slot 1.
0 = No option, 1 = No comm, 2 = Unknown, 3 = FEN-01,
4 = FEN-11, 5 = FEN-21, 6 = FIO-01, 7 = FIO-11,
8 = FPBA-01, 9 = FPBA-02, 10 = FCAN-01, 11 = FDNA-01,
12 = FENA-01, 13 = FENA-02, 14 = FLON-01,
15 = FRSA-00, 16 = FMBA-01, 17 = FFOA-01,
18 = FFOA-02, 19 = FSEN-21, 20 = FEN-31, 21 = FIO-21,
22 = FSCA-01, 23 = FSEA-21, 24 = FIO-31, 25 = FECA-01
Displays the type of the optional module in option slot 2. See
signal 09.20 Option slot1.
Displays the type of the optional module in option slot 3. See
signal 09.20 Option slot1.
Start/stop/direction etc. signal source selections.
Selects the source of start and stop commands for external
control location 1 (EXT1).
Note: This parameter cannot be changed while the drive is
running.
No start or stop command sources selected.
The source of the start and stop commands is selected by
parameter 10.02 Ext1 start
source bit are interpreted as follows:
State of source Command
(via par 10.02)
0 - > 1
Start
1 - > 0
Stop
in1. The state transitions of the
FbEq
-
1 = 1
-
-
1 = 1
-
1 = 1
1 = 1
1 = 1
0
1