Valcom V-D11025B Installation Manual
  1. Manuals
  2. Brands
  3. Valcom Manuals
  4. Clock
  5. V-D11025B
  6. Installation manual

Valcom V-D11025B Installation Manual

Wired digital clock
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation Manual V10.5
Valcom Wired Digital Clock
V-D11025B, V-D11040B, V-2425B-6, and V-D2440B-6
Current as of February 2017
Valcom, Inc.
P. 540-563-2000
5614 Hollins Road
F. 540-362-9800
Roanoke, VA 24019
www.valcom.com
USA

Advertisement

Table of Contents
loading

Related Manuals for Valcom V-D11025B

Summary of Contents for Valcom V-D11025B

  • Page 1 Installation Manual V10.5 Valcom Wired Digital Clock V-D11025B, V-D11040B, V-2425B-6, and V-D2440B-6 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Current as of February 2017...

  • Page 2: Table Of Contents

    Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Valcom Digital Series 2-Wire and 3-Wire Clocks Table of Contents Table of Contents Important Safety Instructions 4 - 10 Wall Mount Installation 11 - 19 Flag Mount Installation...

  • Page 3: Important Safety Instructions

    VERY IMPORTANT: KNOW YOUR COMMUNICATION PROTOCOL The Valcom V-D110XXB Digital clocks are designed to support various 3-wire (sync-wire) communication protocols. To run each protocol properly, the clock requires the correct wiring format. It is very important that you only follow the wiring instructions appropriate to your clock’s communication protocol. Using the wrong wiring format may damage the clock.

  • Page 4: Wall Mount Installation

    4 wall anchors for those screws if you decide not to attach the clock directly to the gang box. If any of the items listed in the wiring kit are missing, you may contact Valcom and order a...
  • Page 5 If you are using the 24 volt model, make sure that the wiring leading to the clock is from a Valcom power supply or V-VCU. 3) Attach the communication and power wires from 4) If you do not wish to attach the housing to the your kit to the communication and power wires gang box, proceed to step 5A.
  • Page 6 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Wall Mount Installation 5A) If you do not wish to attach the housing to a 5B) Identify the keyholes towards the top of the gang box, place the mounting piece on the wall.
  • Page 7 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Wall Mount Installation 5E) Use a pencil to trace the holes beneath each 5F) Repeat step 5D, then pass another pair of #8 keyhole onto the wall. Take the clock housing off...
  • Page 8 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com 7 8A Wall Mount Installation 7) Detach the filter from the clock display board by 8A) If you are installing a digital clock that uses a pressing inward on the red tabs.
  • Page 9 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Wall Mount Installation 9) Detach the frame from the front of the clock 10) Use the 6-19x1/2 screws to attach the display housing by pulling the bottom and top edges away board to the housing.

  • Page 10: Wall Mount Installation

    Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com 13 14 Wall Mount Installation 13) Place the housing frame onto the housing. You 14) Power the clock. After testing the LED segments should hear a snapping noise as the latches drop and presenting some diagnostic information, the into place.

  • Page 11: Flag Mount Installation

    Included in Pole Kit (V-DMKIT) Dual-mount pole, including mounting plate #10-32x3/8 green screw #8-32x7/16 screw M3.5-1.0x10 screw (black) Internal-tooth washer Continued on next page If any of the items listed in the kits are missing, you may contact Valcom and order a replacement kit.
  • Page 12 4 wall anchors for those screws if you decide not to attach the clock directly to the gang box. If any of the items listed in the wiring kit are missing, you may contact Valcom and order a...
  • Page 13 If you are using the 24 volt model, make sure 11” Minimum that the wiring leading to the clock is from a Valcom power supply or V-VCU. 3) Detach the mounting plate from the mounting 4) Attach the mounting plate to the gang box using pole by unscrewing the two screws.
  • Page 14 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Flag Mount Installation Steps 5 and 6 only apply to metal mounting poles. If you have an ABS mounting pole, skip to step 7 5) Remove the mounting pole end cap and the plastic ring from one of the holes.
  • Page 15 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Flag Mount Installation 7) Remove the mounting plate and drill the four 8) Reattach the mounting plate, this time using all holes that were just traced. Insert the four wall four long, silver #6-32x1 screws, then insert the anchors into the holes.
  • Page 16 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Flag Mount Installation 11 12 11) Detach the frame from the front of the clock 12) Insert the four #8-32x7/16 screws through the housing by pulling the bottom and top edges away internal-tooth washers, then through the adapter, from the housing.
  • Page 17 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Flag Mount Installation 15A 15B 15A) If you are installing a digital clock that uses a 15C) If you are installing a digital clock that uses 2-wire digital sync system, attach the wires to the sync-wire correction, attach the wires to the port as shown below.
  • Page 18 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Flag Mount Installation 17) Use the 6-32x12 screws to attach the display 18) Remove the plastic cover from the display board. board to the housing. NOTE: For 2.5” Digit clocks, the holes for the screws will be on the left and right inner surfaces of the housing.
  • Page 19 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Flag Mount Installation 21) Hang the base of the pole on the mounting plate so that the lip is on top of the base, and the holes for the screws are on the bottom of the base.

  • Page 20: Double Mount Installation

    Included in Pole Kit (V-DMKIT) Dual-mount pole, including mounting plate #10-32x3/8 green screw #8-32x7/16 screw M3.5-1.0x10 screw (black) Internal-tooth washer Continued on next page If any of the items listed in the kits are missing, you may contact Valcom and order a replacement kit.
  • Page 21 4 wall anchors for those screws if you decide not to attach the clock directly to the gang box. If any of the items listed in the wiring kit are missing, you may contact Valcom and order a...
  • Page 22 If you are using the 24 volt model, make sure 11” Minimum that the wiring leading to the clock is from a Valcom power supply or V-VCU. 3) Detach the mounting plate from the mounting 4) Attach the mounting plate to the gang box using pole by unscrewing the two screws.
  • Page 23 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Double Mount Installation 5) Remove the mounting plate and drill the four 6) Reattach the mounting plate, this time using all holes that were just traced. Insert the four wall four long, silver #6-32x1 screws, then insert the anchors into the holes.

  • Page 24: Internal-Tooth Washer

    Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Double Mount Installation 9 10 9) Detach the frame from the front of each clock 10) Insert the four #8-32x7/16 screws through the housing by pulling the bottom and top edges away internal-tooth washers, then through each adapter, from the housing.
  • Page 25 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Double Mount Installation 13) Attach the signal and power wires from your kit to the wires you threaded through the poles. Consult the diagrams below for additional help, or see the sections of this manual labeled “3-Wire Synchronous (Sync-Wire) Communication Wiring Information”...
  • Page 26 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Double Mount Installation 14A14B 14A) If you are installing digital clocks that use a 14C) If you are installing digital clocks that use sync- 2-wire digital sync system, attach the wires to the wire correction, attach the wires to the appropriate port as shown below.
  • Page 27 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Double Mount Installation 16) Use the M3.5-1.5x12 screws to attach a display 17) Remove the plastic cover from each display board. board to each housing. NOTE: For 2.5” Digit clocks, the holes for the screws will be on the left and right inner surfaces of the housing.
  • Page 28 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Double Mount Installation 20) Hang the base of the pole on the mounting plate so that the lip is on top of the base, and the holes for the screws are on the bottom of the base.

  • Page 29: Adjustable Jumper Settings

    Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Adjustable Jumper Settings Every version of the digital clock contains a set of jumpers which can be moved to change a particular setting. The functions and positions of each jumper are described below:...

  • Page 30: Inputs

    Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Inputs - System-Side - 2-Wire Digital Valcom Master Clock 18 19 Data In V-C6124P V-CCU 24 volt outputs 24 VDC IN 2 Wire Digital Output to Clocks...
  • Page 31 V-A11012 or V-A11016 V-A11012B or V-A11016B Neutral J1-1 Reset J1-2 Power Black Neutral White Green V-D11025B or V-D11040B Ground Red & Blue Wires are NOT provided by Valcom Neutral White Power Black Reset Yellow Green Ground V-A11012 or V-A11016 V-A11012B or V-A11016B...

  • Page 32: Clock Side - Sync-Wire

    Valcom, Inc. Valcom, Inc. P. 540-563-2000 P. 540-563-2000 5614 Hollins Road 5614 Hollins Road F. 540-362-9800 F. 540-362-9800 Roanoke, VA 24019 Roanoke, VA 24019 www.valcom.com www.valcom.com Inputs - Clock-Side - Sync-Wire (V-D110XXB Only) Inputs for sync-wire protocols are located on the upper-port block on the back of the clock.

  • Page 33: Minute Correction

    Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Inputs - Clock-Side - Sync-Wire (V-D110XXB Only) 58 Minute Correction 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 Neutral...
  • Page 34 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Inputs - Clock-Side - Sync-Wire (V-D110XXB Only) National Time/Rauland 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 Neutral Relay Reset N.O.

  • Page 35: Clock Side - Sync-Wire

    Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Inputs - Clock-Side - Sync-Wire (V-D110XXB Only) Dukane 1 2 3 4 5 6 7 8 9 Reset Minute Pulse Ground Description: Dukane - Applying a 4-10 millisecond pulse on the minute line will increment the clock in one minute.

  • Page 36: Outputs

    Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Outputs (V-D110XXB Only) 2-Wire Digital - Master Mode During a loss of communication with the Master Clock, the V-D110XXB digital clock can act as a temporary, backup master clock for other clocks in the system. The port block on the bottom left side of the circuit board will be called J7.

  • Page 37: Manual Controls

    Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Manual Controls (V-D110XXB Only) The purpose of this section is to get a new digital clock up and running using the manual controls on the front of the digital clock.
  • Page 38 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Manual Controls (V-D110XXB Only) The numbers shown on the left are examples. Going down the list and entering every one of the examples exactly as shown will cause the clock to malfunction or use incorrect data.
  • Page 39 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Manual Controls (V-D110XXB Only) The numbers shown on the left are examples. Going down the list and entering every one of the examples exactly as shown will cause the master clock to malfunction or use incorrect data.
  • Page 40 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Manual Controls (V-D110XXB Only) The numbers shown on the left are examples. Going down the list and entering every one of the examples exactly as shown will cause the clock to malfunction or use incorrect data.
  • Page 41 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Manual Controls (V-D110XXB Only) The numbers shown on the left are examples. Going down the list and entering every one of the examples exactly as shown will cause the clock to malfunction or use incorrect data.
  • Page 42 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Manual Controls (V-D110XXB Only) The numbers shown on the left are examples. Going down the list and entering every one of the examples exactly as shown will cause the clock to malfunction or use incorrect data.
  • Page 43 Program your clock setting based off of the instructions in the description on the right. The settings below only apply to Valcom analog clocks using wired communication protocols such as 2-Wire Digital. The digital clock cannot send these commands to Wireless, IP or Wi-Fi clocks.

  • Page 44: Reading The Display

    Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Reading the Display The digital clock is designed to display time in either a 12-hour or 24-hour format. When the display is set to the 12-hour format, a circular light will appear in the top left corner of the display to indicate PM, or disappear to indicate AM.

  • Page 45: Frequently Asked Questions

    Can this digital clock be used as a standalone clock? The Valcom Digital V-D110XXB can be used as a standalone clock, but it will not keep synchronized time in this configuration. Instead, it will rely on an internal quartz oscillator for keeping the time. The clock will drift by a few seconds each year while in this mode, and will need to be readjusted manually.

  • Page 46: Troubleshooting

    Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Troubleshooting The clock is not running. What do I do? 1. Measure the input voltage to the clock. The voltage should measure 85-135 volts in the 120VAC model or 240VAC model or 10-28 volts in the 2.5”/24VDC model and 16-28 volt in the 4.0”/24VDC model.

  • Page 47: Warranty

    Warranty Valcom, Inc. warrants its products only to the original purchaser, for its own use, to be free from defects in materials and workmanship under conditions of normal use and service for a period of one year from the date of shipment.

This manual is also suitable for:

V-d11040bV-2425b-6V-d2440b-6

Table of Contents