Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Valcom V-A2412
Summary of Contents for Valcom V-A2412
- Page 1 Installation Manual V2.0 Valcom Wired Analog Clocks V-A2412 / V-A2412B and V-A2416 / V-A2416B V-A11012 / V-A11012B and V-A11016 / V-A11016B Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Current as of November 2016...
-
Page 2: Table Of Contents
Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Valcom Wired Analog Clocks Table of Contents Table of Contents Important Safety Instructions Identify Your Clock 5 - 8 Wall Mount Installation - 9 - 15 Flag Mount Installation -... -
Page 3: Important Safety Instructions
VERY IMPORTANT: KNOW YOUR COMMUNICATION PROTOCOL The Valcom Wired clock is designed to support the 2-Wire Digital Communication Protocol as well as 3-wire (sync-wire) communication protocols. To run either system properly, the clock requires the correct wiring format. It is very important that you only follow the wiring instructions appropriate to your clock’s communication protocol. -
Page 4: Identify Your Clock
Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Identify Your Clock A label containing the part number of your clock is attached to the clock movement. ORIGINAL CLOCKS B-MODEL CLOCKS V-A2412 V-A2412B V-A2416 V-A2416B V-A11012... -
Page 5: Wall Mount Installation
If any of the items listed in the wiring kit are missing, you may contact Valcom and order a... -
Page 6: Wall Mount Installation
43.2 cm If you are using the 24 volt model, make sure that the wiring leading to the clock is from a Valcom power supply or V-VCU. 3) Attach the communication, power, 4) Use the #6-32x1/2 screws to attach the mounting and grounding wires from your kit to the bracket to the gang box. - Page 7 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Wall Mount Installation 5) Use the pencil to mark the location of the large, 6) Insert the wall anchor into the hole, then reattach circular hole at the top of the mounting bracket.
- Page 8 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Wall Mount Installation 9) Attach the clock to the mounting piece so that the hole at the top of the clock lines up with the hole at the top of the mounting piece, and the hole at the bottom of the clock lines up with the hole at the bottom of the mounting piece.
-
Page 9: Flag Mount Installation
(not used) #8x1.5 Self-tapping screw (not used) Wall anchor (not used) Additional grounding wire with connector Continued on next page If any of the items listed in the kits are missing, you may contact Valcom and order a replacement kit. -
Page 10: Flag Mount Installation
If any of the items listed in the kits are missing, you may contact Valcom and order a replacement kit. - Page 11 If you are using the 24 volt model, make sure that the wiring leading to the clock is from a Valcom power supply or V-VCU. 3) Detach the mounting plate from the mounting 4) Attach the mounting plate to the gang box using pole by unscrewing the two screws.
- Page 12 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Flag Mount Installation 5) Remove the mounting plate and drill the four 6) Reattach the mounting plate, this time using all holes that were just traced. Insert the four wall four long, silver #8 screws, then insert the four anchors into the holes.
- Page 13 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Flag Mount Installation 9) Insert the four #8-32x7/16 screws through the 10) Thread at least fifteen inches (38.1cm) of wiring internal-tooth washers, then through the adapter, from the gang box through the bottom of the pole and finally into the pole.
- Page 14 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Flag Mount Installation 12) Attach the power connector to the wires you threaded through the pole. Consult the diagrams below for additional help, or see the sections of this manual labeled “3-Wire Synchronous (Sync-Wire) Communication Wiring Information”...
- Page 15 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Flag Mount Installation 15) Remove the outer adapter screws, then slide the clock onto the adapter in the rotation that you wish it to be viewed. You should hear a snapping noise as the four clips on the adapter secure the clock in place.
-
Page 16: Double Mount Installation
Roanoke, VA 24019 www.valcom.com Double Mount Installation Included in Package Description Quantity Picture Valcom analog clock Mounting Bracket (not used) Included in Double Mount Kit Dual-mount pole, including mounting plate and adapters #10-32x3/8 green screw Included in Wiring Kit (A-PK-12-2A) -
Page 17: Double Mount Installation
If you are using the 24 volt model, make sure that the wiring leading to the clock is from a Valcom power supply or V-VCU. 3) Detach the mounting plate from the mounting 4) Attach the mounting plate to the gang box using pole by unscrewing the two screws. - Page 18 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Double Mount Installation 5) Remove the mounting plate and drill the four 6) Reattach the mounting plate, this time using all holes that were just traced. Insert the four wall four long, silver #8 screws, then insert the four anchors into the holes.
- Page 19 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Double Mount Installation 9) Attach the base of the pole to the mounting plate so that the lip is on the top of the base, and the holes for the screws are on the bottom of the base.
- Page 20 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com 11 12 Double Mount Installation 11) Remove the gearbox pin, then, if the case is 12) Attach a power connector to the ports on the made of metal, attach the grounding wire to the bottom of each movement.
- Page 21 Output to Clocks + - + - + - + - + - + - *V-C6124P and the V-CCU are ordered as a V-VCU. White Black V-A2412 or V-A2416 V-A2412B or V-A2416B Orange Yellow V-D2425B or V-D2440B White Black V-A2412 or V-A2416...
- Page 22 Warranty Valcom, Inc. warrants its products only to the original purchaser, for its own use, to be free from defects in materials and workmanship under conditions of normal use and service for a period of one year from the date of shipment.
- Page 23 24 AND 23 or the pair 26 AND 27 Neutral White Power Black Reset Yellow Green Ground 24VDC V-A2412 or V-A2416 V-A2412B or V-A2416B Neutral White Power Black Reset Yellow Green Ground V-A2412 or V-A2416 V-A2412B or V-A2416B...
-
Page 24: Wire Synchronous (Sync-Wire) Communication 110Vac
F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Wiring Information - 3-Wire Synchronous (Sync-Wire) Communication 110VAC Valcom Master Clock 27 26 25 24 23 22 Clock Circuit 1 10 Amp Contact Rating Clock Circuit * ”or” means one pair of ports or the other. -
Page 25: Frequently Asked Questions
The clock will begin to run, but the time displayed will be incorrect. As soon as signal wires from the master clock are connected and a synchronization signal is sent, the Valcom Wired Clock will correct itself to display the correct time. - Page 26 See the sections on the pages labeled “Diagnostic Test #1 - Protocol Verification”, “Diagnostic Test #2 - Comprehensive Test”, or “Diagnostic Test #3 - Manufacturing Default”, depending on your needs. I am adding a new clock into an existing Valcom Wired Clock System. Do I have to set my entire system back to 12:00? No.
-
Page 27: Troubleshooting
Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Troubleshooting The clock is plugged into the power, but it is not running. What should I do? a) Make sure that the movement’s gearbox pin is removed. - Page 28 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Diagnostic Test #1 - Protocol Verification (Original Only) The purpose of Diagnostic #1 is to tell the user which protocol the master clock is using to communicate with the secondary clock.
- Page 29 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Diagnostic Test #1 - Protocol Verification (B-Model Only) The purpose of Diagnostic #1 is to tell the user which protocol the master clock is using to Button communicate with the secondary clock.
- Page 30 Button Diagnostic #2 may be enabled by holding down the diagnostic button for three seconds. If the Valcom Wired clock is performing this diagnostic, then a green LED on the movement will flash twice every three seconds. It will continue to flash twice every three seconds until the diagnostic is complete.
- Page 31 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Diagnostic Test #2 - Comprehensive Test (B-Model Only) The purpose of Diagnostic #2 is to test the Movement gearbox and electrical components of your clock. Button Diagnostic #2 may be enabled by pressing the diagnostic button twice.
- Page 32 Button Diagnostic #3 may be enabled by holding down the diagnostic button for five seconds. If the Valcom Wired clock is performing this diagnostic, then a green LED on the back will flash three times with a five second break between each flash. The LED will continue to flash green until the diagnostic is complete.
- Page 33 Valcom, Inc. P. 540-563-2000 5614 Hollins Road F. 540-362-9800 Roanoke, VA 24019 www.valcom.com Diagnostic Test #3 - Manufacturing Default (B-Model Only) The purpose of Diagnostic #3 is to bring the clock Button back to 12:00:00 and reset to the manufacturer’s default.