Serial Communications Look-Up Table; Trip Categories - Emerson Mentor MP Advanced User's Manual

Parameter Keypad and
structure
Table 5-9

Serial communications look-up table

No. String
1 UV
2 t002
3 AOC
4 t004
5 PS
6 Et
7 O.SPd
8 PS.10V
9 PS.24V
10 t010
11 tunE1
12 tunE2
13 tunE3
14 tunE4
15 tunE5
16 tunE6
17 tunE7
18 tunE
19 t019
20 It.AC
21 O.ht1
22 O.ht2
23 t023
24 th
25 thS
26 O.Ld1
27 O.ht3
28 cL2
29 cL3
30 SCL
31 EEF
32-33 t032 - t033
34 Pad
35 CL.bit
36 SAVE.Er
37 PSAVE.Er
38-39 t038 - t039
40-89 t040 - t089
90 UP div0
91 UP Par

Trip Categories

Trips can be grouped into the following categories. It should be noted that a trip can only occur when the drive is not tripped or is already tripped but
with a trip with a lower priority number.
Priority Category
1 Hardware faults
2 Non-resetable trips
3 EEF trip
4 SMARTCARD trips
4 Encoder power supply trips
5 Normal trips
6 Self resetting trips
Unless otherwise stated, trips cannot be reset until 1.0 s after the trip has been accepted by the drive.
Mentor MP Advanced User Guide
Issue Number: 4
format
Parameter description
No.
92
93
94
95
96
97
98
99
100
101
102-111
112-155
156
157
158
159
160
161
162-167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
Trips
HF01 to HF16
HF17 to HF29, SL1.HF,
SL2.HF, SL3.HF
EEF
C.Boot, C.Busy, C.Chg,
C.Optn, C.RdO, C.Err, C.dat,
C.FULL, C.Acc, C.rtg, C.Typ,
C.cpr
Enc1, Enc3
All other trips not included in
this table
UV
www.onxcontrol.com
Advanced parameter Serial comms
protocol
descriptions
String No.
UP ro 189
UP So 190
UP ovr 191
UP OFL 192-196
UP uSEr 197
UP udf 198
UP ACC 199
t099 200
201
t101 202
t102 - t111 203
t112 - t155 204
SLAVE.Er 205
F.OVL 206
AOP 207
FbL 208
Fbr 209
AtL.Err 210
t162 - t167 211
FdL 212
FOC 213
SL 214
S.OLd 215
S.OV 216
th.Err 217-229
PLL Err
C.Prod
t176
C.Boot
C.BUSy
C.Chg
C.Optn
C.RdO
C.Err
C.dat
C.FULL
C.Acc
C.rtg
C.Typ
C.cpr
These indicate fatal problems and cannot be reset. The drive is
inactive after one of these trips and the display shows HFxx
Cannot be reset
Cannot be reset unless a code to load defaults is first entered in
Pr x.00
SMARTCARD trips have priority 5 during power up
These trips can only override the following priority 5 trips: Enc2, Enc9
or Enc10
Under voltage trip cannot be reset by the user, but is automatically
reset by the drive when the supply voltage is within specification. Trip
not saved to EEProm
Performance Menu 10
String
EnC1
EnC2
EnC3
t192 - t196
EnC9
EnC10
dESt
SL1.HF
SL1.tO
SL1.Er
SL1.nF
SL1.dF
SL2.HF
SL2.tO
SL2.Er
SL2.nF
SL2.dF
SL3.HF
SL3.tO
SL3.Er
SL3.nF
SL3.dF
SL.rtd
t216
HF17 – HF29
Comments
139