Trip Categories; Table 13-2 Serial Communications Look-Up Table; Table 13-3 Trip Categories - Emerson MP25A4 User Manual

Safety Product Mechanical
Information information Installation

Table 13-2 Serial communications look-up table

No. String
1 UV
2 t002
3 AOC
4 t004
5 PS
6 Et
7 O.SPd
8 PS.10V
9 PS.24V
10 t010
11 tunE1
12 tunE2
13 tunE3
14 tunE4
15 tunE5
16 tunE6
17 tunE7
18 tunE
19 t019
20 It.AC
21 O.ht1
22 O.ht2
23 t023
24 th
25 thS
26 O.Ld1
27 O.ht3
28 cL2
29 cL3
30 SCL
31 EEF
32-33 t032 - t033
34 Pad
35 CL.bit
36 SAVE.Er
37 PSAVE.Er
38-39 t038 - t039
40-89 t040 - t089
90 UP div0
13.3

Trip categories

Trips can be grouped into the following categories. It should be noted that a trip can only occur when the drive is not tripped or is already tripped but
with a trip with a lower priority number.

Table 13-3 Trip categories

Priority Category
1 Hardware faults
2 Non-resetable trips
3 EEF trip
4 SMARTCARD trips
4 Encoder power supply trips
5 Normal trips
6 Self reseting trips
Unless otherwise stated, trips cannot be reset until 1.0s after the trip has been accepted by the drive.
174
Electrical Getting Basic
installation started parameters
No.
91
92
93
94
95
96
97
98
99
100
101
102-111
112-156
157
158
159
160
161-167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
Trips
HF01 to HF16
HF17 to HF29, SL1.HF, SL2.HF,
SL3.HF
EEF
C.Boot, C.Busy, C.Chg, C.Optn,
C.RdO, C.Err, C.dat, C.FULL,
C.Acc, C.rtg, C.Typ, C.cpr,
Enc1, Enc2
All other trips not included in this
table
UV
www.controltechniques.com
Running SMARTCARD
Optimization
the motor operation
String
UP Par
UP ro
UP So
UP ovr
UP OFL
UP uSEr
UP udf
UP ACC
t099
t101
t102 - t111
t112 - t156
F.OVL
AOP
FbL
Fbr
t161 - t167
FdL
FOC
SL
S.OLd
S.OV
th.Err
PLL Err
C.Prod
t176
C.Boot
C.BUSy
C.Chg
C.Optn
C.RdO
C.Err
C.dat
C.FULL
C.Acc
C.rtg
C.Typ
C.cpr
These indicate fatal problems and cannot be reset. The drive is
inactive after one of these trips and the display shows HFxx.
Cannot be reset
Cannot be reset unless a code to load defaults is first entered in
parameter x.00
SMARTCARD trips have priority 5 during power up.
These trips can only override the following priority 5 trips: Enc2, Enc9
or Enc10
Can be reset after 1.0s
Under voltage trip cannot be reset by the user, but is automatically
reset by the drive when the supply voltage is with specification.
Onboard Advanced Technical
Diagnostics
PLC parameters data
No. String
189 EnC1
190 EnC2
191 EnC3
192-196 t192 - t196
197 EnC9
198 EnC10
199
200 SL1.HF
201 SL1.tO
202 SL1.Er
203 SL1.nF
204 SL1.dF
205 SL2.HF
206 SL2.tO
207 SL2.Er
208 SL2.nF
209 SL2.dF
210 SL3.HF
211 SL3.tO
212 SL3.Er
213 SL3.nF
214 SL3.dF
215 SL.rtd
216
217-229 HF17 – HF29
Comments
Mentor MP User Guide
UL
information
dESt
t216
Issue: 3