Docomo f-01c Instruction Manual page 139

Upper slot : Command
Lower slot : Example
*1
AT+CBST=<n>,1,0
AT+CBST=116,1,0
OK
*1
AT+CDIP=<n>
AT+CDIP=0
OK
AT+CEER
AT+CEER
+CEER : 36
OK
*2
AT+CGDCONT
→P36
*2
AT+CGEQMIN
→P37
*2
AT+CGEQREQ
→P37
AT+CGMR
AT+CGMR
1234567890123456
OK
*1
AT+CGREG=<n>
AT+CGREG=0
OK
AT+CGSN
AT+CGSN
123456789012345
OK
*1
AT+CLIP=<n>
AT+CLIP=0
OK
*2
AT+CLIR=<n>
AT+CLIR=2
OK
*1
AT+CMEE=<n>
AT+CMEE=0
OK
Set the line to use (Setting of bearer service)
n=116 : 64K data communication (default) n=134 : 64K videophone
AT+CBST? : Display current settings AT+CBST=? : Display a list of assignable values
Set to notify/not to notify the sub address when receiving in packet communication or 64
data communication. And, subscription status of Multi Number can be confirmed.
n=0 : The information of sub address is not displayed. (default)
n=1 : The information of sub address is displayed.
m=0 : Multi Number not subscribed. m=1 : Multi Number subscribed.
AT+CDIP? : Display the current settings and status in the "+CDIP:<n>,<m>" format
AT+CDIP=? : List of the settable values is displayed.
Display the reason of immediate disconnection.
Disconnection reason list→P35
Set dialup connection (APN) for packet communication.→P36
Set the criteria for judging whether to permit QoS (Quality of Service) provisioned by the
network when packet communication is established.→P37
Set QoS (Quality of Service) requested to the network at the transmission of packet
communication.→P37
Display FOMA terminal version.
Set whether to report network service registration status (Within/Out).
n=0 : Not notified (default)
n=1 : When the terminal is moved from Within service area to Out of service area or vice
versa, the status is reported in the "+CGREG : <stat>" format.
stat=0 : Out of packet service area stat=1 : Within packet service area
stat=4 : Unknown
stat=5 : Within packet service area (during international roaming)
AT+CGREG? : Display the current settings and status in the "+CGREG : <n>,<stat>" format
AT+CGREG=? : Display a list of assignable values
Display FOMA terminal serial No.
Set whether to display sender's caller ID on a PC when receiving 64K data communication.
n=0 : Not display result (default) n=1 : Display result
m=0 : Network setting not to send caller ID
m=1 : Network setting to send caller ID m=2 : Unknown
AT+CLIP? : Display the current settings and status in the "+CLIP : <n>,<m>" format
AT+CLIP=? : Display a list of assignable values
Set Caller ID notification when sending 64K data communication.
n=0 : Use the setting in Caller ID notification of FOMA terminal n=1 : Not send
n=2 : Send (default)
m=0 : CLIR not operating (always sends) m=1 : CLIR operating (never sends)
m=2 : Unknown m=3 : CLIR temporary mode (default=does not send)
m=4 : CLIR temporary mode (default=sends)
AT+CLIR? : Display the current settings and status in the "+CLIR : <n>,<m>" format
AT+CLIR=? : Display a list of assignable values
Set whether to display an error report at FOMA terminal.
n=0 : Display "ERROR" and no result code (default)
n=1 : Use result code, displaying reason as number
n=2 : Use result code, displaying reason as alphabetic characters
Display reasons in the "+CME ERROR : xxxx" format when n=1 or n=2 is set (xxxx = number
or alphabetic characters).→P36 "Error messages list"
AT+CMEE? : Display current settings AT+CMEE=? : Display a list of assignable values
Description
33